Gigabyte GA-8IP775: Chapter 2 BIOS Setup

2-1 Standard CMOS Features

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features

Date (mm:dd:yy) Mon, May 10 2004

Item Help

English

Time (hh:mm:ss) 22:31:24

Menu Level`

` IDE Channel 0 Master [None]

Change the day, month,

` IDE Channel 0 Slave [None]

year

` IDE Channel 1 Master [None]

` IDE Channel 1 Slave [None]

<Week>

Sun. to Sat.

Drive A [1.44M, 3.5"]

Drive B [None]

<Month>

Floppy 3 Mode Suport [Disabled]

Jan. to Dec.

Holt On [All, But Keyboard]

<Day>

1 to 31 (or maximum

Base Memory 640K

allowed in the month)

Extended Memory 127M

Total Memory 128M

<Year>

1999 to 2098

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Save Default F7: Optimized Defaults

Date

The date format is <week>, <month>, <day>, <year>.

Week The week, from Sun to Sat, determined by the BIOS and is display only

Month The month, Jan. Through Dec.

Day The day, from 1 to 31 (or the maximum allowed in the month)

Year The year, from 1999 through 2098

Time

The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour

military-time clock. For example, 1 p.m. is 13:00:00.

IDE Channel 0 Master, Slave/IDE Channel 1 Master, Slave

IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection.

IDE Channel 0 Master(Slave)/IDE Channel 1 Master(Slave) IDE Device Setup. You can use one of

three methods:

Auto Allows BIOS to automatically detect IDE devices during POST(default)

None Select this if no IDE devices are used and the system will skip the automatic

detection step and allow for faster system start up.

Manual User can manually input the correct settings

Access Mode Use this to set the access mode for the hard drive. The four options are:

CHS/LBA/Large/Auto(default:Auto)

Hard drive information should be labeled on the outside drive casing. Enter the appropriate option

based on this information.

Cylinder Number of cylinders

Head Number of heads

Precomp Write precomp

Landing Zone Landing zone

Sector Number of sectors

If a hard disk has not been installed, select NONE and press <Enter>.

GA-8IP775 Series Motherboard - 32 -

English

Drive A / Drive B

The category identifies the types of floppy disk drive A or drive B that has been installed in the computer.

None No floppy drive installed

360K, 5.25" 5.25 inch PC-type standard drive; 360K byte capacity.

1.2M, 5.25" 5.25 inch AT-type high-density drive; 1.2M byte capacity

(3.5 inch when 3 Mode is Enabled).

720K, 3.5" 3.5 inch double-sided drive; 720K byte capacity

1.44M, 3.5" 3.5 inch double-sided drive; 1.44M byte capacity.

2.88M, 3.5" 3.5 inch double-sided drive; 2.88M byte capacity.

Floppy 3 Mode Support (for Japan Area)

Disabled Normal Floppy Drive. (Default value)

Drive A Drive A is 3 mode Floppy Drive.

Drive B Drive B is 3 mode Floppy Drive.

Both Drive A & B are 3 mode Floppy Drives.

Halt on

The category determines whether the computer will stop if an error is detected during power up.

No Errors The system boot will not stop for any error that may be detected and you

will be prompted.

All Errors Whenever the BIOS detects a non-fatal error the system will be stopped.

All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other

errors. (Default value)

All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors.

All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all

other errors.

Memory

The category is display-only which is determined by POST (Power On Self Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory installed

in the system.

The value of the base memory is typically 512K for systems with 512K memory installed on

the motherboard, or 640K for systems with 640K or more memory installed on the motherboard.

Extended Memory

The BIOS determines how much extended memory is present during the POST.

This is the amount of memory located above 1 MB in the CPU's memory address map.

Total Memory

This item displays the memory size that used.

BIOS Setup- 33 -

2-2 Advanced BIOS Features

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Advanced BIOS Features

X Hard Disk Boot Priority [Press Enter]

Item Help

English

First Boot Device [Floppy]

Menu Level`

Second Boot Device [Hard Disk]

Third Boot Device [CDROM]

Select Hard Disk Boot

Password Check [Setup]

Device Priority

# CPU Hyper-Threading [Enabled]

Limit CPUID Max. to 3 [Enabled]

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Save Default F7: Optimized Defaults

®

®

" # " System will detect automatically and show up when you install the Intel

Pentium

4

processor with HT Technology.

Hard Disk Boot Priority

Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc.

Use < > or < > to select a device, then press<+> to move it up, or <-> to move it down the list. Press

<ESC> to exit this menu.

First / Second / Third Boot Device

Floppy Select your boot device priority by Floppy.

LS120 Select your boot device priority by LS120.

Hard Disk Select your boot device priority by Hard Disk.

CDROM Select your boot device priority by CDROM.

ZIP Select your boot device priority by ZIP.

USB-FDD Select your boot device priority by USB-FDD.

USB-ZIP Select your boot device priority by USB-ZIP.

USB-CDROM Select your boot device priority by USB-CDROM.

USB-HDD Select your boot device priority by USB-HDD.

LAN Select your boot device priority by LAN.

Disabled Select your boot device priority by Disabled.

Password Check

Setup The system will boot but will not access to Setup page if the correct

password is not entered at the prompt. (Default value)

System The system will not boot and will not access to Setup page if the correct

password is not entered at the prompt.

If you want to cancel the setting of password, please just press ENTER to make [SETUP] empty.

GA-8IP775 Series Motherboard - 34 -

English

CPU Hyper-Threading

Enabled Enables CPU Hyper Threading Feature. Please note that this feature is only working

for operating system with multi processors mode supported. (Default value)

Disabled Disables CPU Hyper Threading.

Limit CPUID Max. to 3

Enabled Limit CPUID Maximum value to 3 when use older OS like NT4. (Default value)

Disabled Disables CPUID Limit for windows XP.

BIOS Setup- 35 -

2-3 Integrated Peripherals

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Integrated Peripherals

On-Chip Primary PCI IDE [Enabled]

Item Help

English

On-Chip Secondary PCI IDE [Enabled]

Menu Level`

On-Chip SATA [Auto]

x SATA Port0 Configure as SATA Port0

If a hard disk

SATA Port1 Configure as SATA Port1

controller card is

USB Controller [Enabled]

used, set at Disabled

USB 2.0 Controller [Enabled]

USB Keyboard Support [Disabled]

[Enabled]

USB Mouse Support [Disabled]

Enable on-chip IDE

AC97 Audio [Auto]

Port

(

)

Onboard H/W LAN

*

[Enabled]

(

)

Onboard LAN Boot ROM

*

[Disabled]

[Disabled]

Onboard Serial Port 1 [3F8/IRQ4]

Disable on-chip IDE

Onboard Serial Port 2 [2F8/IRQ3]

Port

UART Mode Select [Normal]

x UR2 Duplex Mode Half

Onboard Parallel Port [378/IRQ7]

Parallel Port Mode [SPP]

x ECP Mode Use DMA 3

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Save Default F7: Optimized Defaults

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Integrated Peripherals

Game Port Address [201]

Item Help

Midi Port Address [Disabled]

Menu Level`

Midi Port IRQ 10

CIR Port Address [Disabled]

x CIR Port IRQ 11

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Save Default F7: Optimized Defaults

On-Chip Primary PCI IDE

Enabled Enable onboard 1st channel IDE port. (Default value)

Disabled Disable onboard 1st channel IDE port.

On-Chip Secondary PCI IDE

Enabled Enable onboard 2nd channel IDE port. (Default value)

Disabled Disable onboard 2nd channel IDE port.

(*) Only for GA-8IP775-G.

GA-8IP775 Series Motherboard - 36 -

English

On-chip SATA

Disabled Disable SATA controller.

Auto When there is no device to be plugged in IDE1 or IDE2, SATA controller

will remap to IDE controller. (Default value)

Manual Set SATA Mode manually.

SATA Port0 Configure as

IDE Pri. Master Remap SATA Port 0 to IDE Pri. Master.

IDE Pri. Slave Remap SATA Port 0 to IDE Pri. Slave.

IDE Sec. Master Remap SATA Port 0 to IDE Sec. Master.

IDE Sec. Slave Remap SATA Port 0 to IDE Sec. Slave.

SATA Port0 SATA controller set to SATA port0. As this mode, it support by WinXP or

later OS only. (Default value)

SATA Port1 SATA controller set to SATA port1. As this mode, it support by WinXP or

later OS only.

SATA Port1 Configure as

The values depend on SATA Port0.

USB Controller

Enabled Enable USB Controller. (Default value)

Disabled Disable USB Controller.

USB 2.0 Controller

Disable this function if you are not using onboard USB 2.0 feature.

Enabled Enable USB 2.0 Controller. (Default value)

Disabled Disable USB 2.0 Controller.

USB Keyboard Support

Enabled Enable USB Keyboard Support.

Disabled Disable USB Keyboard Support. (Default value)

USB Mouse Support

Enabled Enable USB Mouse Support.

Disabled Disable USB Mouse Support. (Default value)

AC97 Audio

Enabled Enable onboard AC'97 audio function. (Default Value)

Disabled Disable this function.

(

)

Onboard H/W LAN

*

Enabled Enable Onboard H/W LAN function. (Default value)

Disabled Disable this function.

(

)

Onboard LAN Boot ROM

*

This function decide whether to invoke the boot ROM of the onboard LAN chip.

Disabled Disable this function. (Default Value)

Enabled Enable this function.

(*) Only for GA-8IP775-G.

BIOS Setup- 37 -

Onboard Serial Port 1

Auto BIOS will automatically setup the port 1 address.

3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8. (Default value)

2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8.

English

3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8.

2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8.

Disabled Disable onboard Serial port 1.

Onboard Serial Port 2

Auto BIOS will automatically setup the port 2 address.

3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8.

2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8. (Default value)

3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8.

2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8.

Disabled Disable onboard Serial port 2.

UART Mode Select

This item allows you to determine which Infra Red(IR) function of Onboard I/O chip.

Normal Set onboard I/O chip UART to Normal Mode. (Default Value)

ASKIR Set onboard I/O chip UART to ASKIR Mode.

IrDA Set onboard I/O chip UART to IrDA Mode.

UR2 Duplex Mode

This feature allows you to seclect IR mode.

This function will available when "UART Mode Select" doesn't set at Normal.

Half IR Function Duplex Half. (Default value)

Full IR Function Duplex Full.

Onboard Parallel port

Disabled Disable onboard LPT port.

378/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default value)

278/IRQ5 Enable onboard LPT port and address is 278/IRQ5.

3BC/IRQ7 Enable onboard LPT port and address is 3BC/IRQ7.

Parallel Port Mode

SPP Using Parallel port as Standard Parallel Port. (Default value)

EPP Using Parallel port as Enhanced Parallel Port.

ECP Using Parallel port as Extended Capabilities Port.

ECP+EPP Using Parallel port as ECP & EPP mode.

ECP Mode Use DMA

3 Set ECP Mode Use DMA to 3. (Default value)

1 Set ECP Mode Use DMA to 1.

GA-8IP775 Series Motherboard - 38 -

English

Game Port Address

201 Set Game Port Address to 201. (Default Value)

209 Set Game Port Address to 209.

Disabled Disable this function.

Midi Port Address

300 Set Midi Port Address to 300.

330 Set Midi Port Address to 330.

Disabled Disable this function. (Default Value)

Midi Port IRQ

5 Set Midi Port IRQ to 5.

10 Set Midi Port IRQ to 10. (Default Value)

CIR Port Address

310 Set CIR Port Address to 310.

320 Set CIR Port Address to 320.

Disabled Disable this function. (Default value)

CIR Port IRQ

5 Set CIR Port IRQ to 5.

11 Set CIR Port IRQ to 11. (Default value)

BIOS Setup- 39 -

2-4 Power Management Setup

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Power Management Setup

English

ACPI Suspend Type [S1(POS)]

Item Help

Power LED in S1 state [Blinking]

Menu Level`

Off by Power button [Instant-off]

PME Event Wake Up [Enabled]

[S1]

ModemRingOn/WakeOnLan [Enabled]

Set suspend type to

Resume by Alarm [Disabled]

Power On Suspend under

x Date (of Month) Alarm Everyday

ACPI OS

x Time (hh:mm:ss) Alarm 0 : 0 : 0

Power On By Mouse [Disabled]

[S3]

Power On By Keyboard [Disabled]

Set suspend type to

x KB Power ON Password Enter

Suspend to RAM under

AC Back Function [Soft-Off]

ACPI OS

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Save Default F7: Optimized Defaults

ACPI Suspend Type

S1(POS) Set ACPI suspend type to S1/POS(Power On Suspend). (Default value)

S3(STR) Set ACPI suspend type to S3/STR(Suspend To RAM).

Power LED in S1 state

Blinking In standby mode(S1), power LED will blink. (Default value)

Dual/OFF In standby mode(S1):

a. If use single color LED, power LED will turn off.

b. If use dual color LED, power LED will turn to another color.

Off by Power button

Instant-off Press power button then Power off instantly. (Default value)

Delay 4 Sec. Press power button 4 sec. to Power off. Enter suspend if button is pressed

less than 4 sec.

PME Event Wake Up

Disabled Disable this function.

Enabled Enable PME Event Wake up. (Default value)

ModemRingOn/WakeOnLAN

An incoming call via modem can awake the system from any suspend state or an input signal

comes from the other client server on the LAN can awake the system from any suspend state.

Disabled Disable Modem Ring on/wake on Lan function.

Enabled Enable Modem Ring on/wake on Lan. (Default value)

GA-8IP775 Series Motherboard - 40 -

English

Resume by Alarm

You can set "Resume by Alarm" item to enabled and key in Data/time to power on system.

Disabled Disable this function. (Default value)

Enabled Enable alarm function to POWER ON system.

If RTC Alarm Lead To Power On is Enabled.

Date (of Month) Alarm : Everyday, 1~31

Time (hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59)

Power On By Mouse

Disabled Disable this function. (Default value)

Double Click Double click on PS/2 mouse left button to power on the system.

Power On By Keyboard

Password Enter from 1 to 5 characters to set the Keyboard Power On Password.

Disabled Disabled this function. (Default value)

Keyboard 98 If your keyboard have "POWER Key" button, you can press the key to

power on the system.

KB Power ON Password

When "Power On by Keyboard" set at Password, you can set the password here.

Enter Input password (from 1 to 5 characters) and press Enter to set the Keyboard

Power On password.

AC Back Function

Soft-Off When AC-power back to the system, the system will be in "Off" state.

(Default value)

Full-On When AC-power back to the system, the system always in "On" state.

Memory When AC-power back to the system, the system will return to the Last state

before AC-power off.

BIOS Setup- 41 -

2-10 Set Supervisor/User Password

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

` Standard CMOS Features

Load Fail-Safe Defaults

English

` Advanced BIOS Features

Load Optimized Defaults

` Integrated Peripherals

Set Supervisor Password

` Power Management Setup

Set User Password

` PnP/PCI Configurations

Enter Password:

Save & Exit Setup

` PC Health Status

Exit Without Saving

` Frequency/Voltage Control

ESC: Quit KLJI: Select Item

F8: Q-Flash F10: Save & Exit Setup

Change/Set/Disable Password

Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically

detects.

When you select this function, the following message will appear at the center of the screen to assist you in

creating a password.

Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password.

Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter

a password.

To disable password, just press <Enter> when you are prompted to enter password. A message

"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is disabled,

the system will boot and you can enter Setup freely.

The BIOS Setup program allows you to specify two separate passwords:

SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS Setup

program function. When enabled, the Supervisor password is required for entering the BIOS Setup program

and having full configuration fields, the User password is required to access only basic items.

If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be prompted for the

password every time the system is rebooted or any time you try to enter Setup Menu.

If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only when

you try to enter Setup.

GA-8IP775 Series Motherboard - 48 -

English

2-11 Save & Exit Setup

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

` Standard CMOS Features

Load Fail-Safe Defaults

` Advanced BIOS Features

Load Optimized Defaults

` Integrated Peripherals

Set Supervisor Password

` Power Management Setup

Set User Password

` PnP/PCI Configurations

Save & Exit Setup

` PC Health Status

Save to CMOS and EXIT (Y/N)? Y

Exit Without Saving

` Frequency/Voltage Control

ESC: Quit KLJI: Select Item

F8: Q-Flash F10: Save & Exit Setup

Save & Exit Setup

Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.

Type "N" will return to Setup Utility.

2-12 Exit Without Saving

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

` Standard CMOS Features

Load Fail-Safe Defaults

` Advanced BIOS Features

Load Optimized Defaults

` Integrated Peripherals

Set Supervisor Password

` Power Management Setup

Set User Password

` PnP/PCI Configurations

Quit Without Saving (Y/N)? N

Save & Exit Setup

` PC Health Status

Exit Without Saving

` Frequency/Voltage Control

ESC: Quit KLJI: Select Item

F8: Q-Flash F10: Save & Exit Setup

Abandon all Data

Type "Y" will quit the Setup Utility without saving to RTC CMOS.

Type "N" will return to Setup Utility.

BIOS Setup- 49 -

English

GA-8IP775 Series Motherboard - 50 -

English

Chapter 3 Install Drivers

Pictures below are shown in Windows XP.

Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver

CD-title will auto start and show the installation guide. If not, please double click the CD-ROM

device icon in "My computer", and execute the setup.exe.

3-1 Install Chipset Drivers

This page shows the drivers that need to be installed for the system. Click each item to install the driver

manually or switch to the to install the drivers automatically.

Some device drivers will restart your system

automatically. After restarting your system the

"Xpress Install" will continue to install other

drivers.

System will reboot automatically after install

the drivers, afterward you can install others

application.

The "Xpress Install" uses the"Click and Go" technology to install the drivers automatically. Just select the

drivers you want then click the "GO" button. The will execute the installation for you by itself.

We recommend that you install all components in the list.

Click "GO".

For USB2.0 driver support under Windows XP operating system, please use Windows Service

Pack. After install Windows Service Pack, it will show a question mark "?" in "Universal Serial Bus

controller" under "Device Manager". Please remove the question mark and restart the system

(System will auto-detect the right USB2.0 driver).

Install Drivers- 51 -

3-2 Software Applications

This page displays all the tools that Gigabyte developed and some free software.

English

3-3 Driver CD Information

This page lists the contents of software and drivers in this CD-title.

GA-8IP775 Series Motherboard - 52 -

English

3-4 Hardware Information

This page lists all device you have for this motherboard.

3-5 Contact Us

Please see the last page for details.

Install Drivers- 53 -

English

GA-8IP775 Series Motherboard - 54 -