Gigabyte GA-8ILMT4: Chapter 3 BIOS Setup
Chapter 3 BIOS Setup: Gigabyte GA-8ILMT4
Chapter 3 BIOS Setup
BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the
basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it
English
retains the Setup information when the power is turned off.
ENTERING
SETUP
Powering ON the computer and pressing <Del> immediately will allow you to enter Setup. If you require
more advanced BIOS settings, please go to “Advanced BIOS” setting menu.To enter Advanced BIOS
setting menu, press “Ctrl+F1” key on the BIOS screen.
CONTROL
KEYS
<!> Move to previous item
<"> Move to next item
<#> Move to the item in the left hand
<$> Move to the item in the right hand
<Esc> Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and
Option Page Setup Menu - Exit current page and return to Main Menu
<+/PgUp> Increase the numeric value or make changes
<-/PgDn> Decrease the numeric value or make changes
<F1> General help, only for Status Page Setup Menu and Option Page Setup Menu
<F2> Reserved
<F3> Reserved
<F4> Reserved
<F5> Restore the previous CMOS value from CMOS, only for Option Page Setup Menu
<F6> Load the file-safe default CMOS value from BIOS default table
<F7> Load the Optimized Defaults
<F8> Q-Flash function
<F9> Reserved
<F10> Save all the CMOS changes, only for Main Menu
- 22 -GA-8ILMT4 Motherboard
English
GETTING HELP
Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of the screen.
Status Page Setup Menu / Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the possible
selections for the highlighted item. To exit the Help Window press <Esc>.
The Main Menu (For example: BIOS Ver. : F1b)
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 1) will appear on the screen.
The Main Menu allows you to select from eight setup functions and two exit choices. Use arrow keys to
select among the items and press <Enter> to accept or enter the sub-menu.
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features Top Performance
!Advanced BIOS Features Load Fail-Safe Defaults
!Integrated Peripherals Load Optimized Defaults
!Power Management Setup Set Supervisor Password
!PnP/PCI Configurations Set User Password
!PC Health Status Save & Exit Setup
!Frequency/Voltage Control Exit Without Saving
ESC:Quit "#$%:Select Item
F8: Q-Flash F10:Save & Exit Setup
Time, Date, Hard Disk Type...
Figure 1: Main Menu
%%
% Standard CMOS Features
%%
This setup page includes all the items in standard compatible BIOS.
% Advanced BIOS Features
%%
%%
This setup page includes all the items of Award special enhanced features.
- 23 - BIOS Setup
%%
%%
% Integrated Peripherals
This setup page includes all onboard peripherals.
%%
%%
% Power Management Setup
English
This setup page includes all the items of Green function features.
% PnP/PCI Configurations
%%
%%
This setup page includes all the configurations of PCI & PnP ISA resources.
%%
%%
% PC Health Status
This setup page is the System auto detect Temperature, voltage, fan, speed.
%%
%%
% Frequency/Voltage Control
This setup page is control CPU’s clock and frequency ratio.
% Top Performance
%%
%%
If you wish to maximize the performance of your system, set "Top Performance" as "Enabled".
% Load Fail-Safe Defaults
%%
%%
Fail-Safe Defaults indicates the value of the system parameters which the system would
be in safe configuration.
%%
%%
% Load Optimized Defaults
Optimized Defaults indicates the value of the system parameters which the system would
be in best performance configuration.
% Set Supervisor password
%%
%%
Change, set, or disable password. It allows you to limit access to the system and Setup,
or just to Setup.
%%
%%
% Set User password
Change, set, or disable password. It allows you to limit access to the system.
%%
%%
% Save & Exit Setup
Save CMOS value settings to CMOS and exit setup.
% Exit Without Saving
%%
%%
Abandon all CMOS value changes and exit setup.
- 24 -GA-8ILMT4 Motherboard
English
Standard CMOS Features
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
Standard CMOS Features
Date (mm:dd:yy) Mon, Feb 21 2000 Item Help
Time (hh:mm:ss) 22:31:24 Menu Level &
Change the day, month,
!IDE Primary Master None year
!IDE Primary Slave None
!IDE Secondary Master None <Week>
!IDE Secondary Slave None Sun. to Sat.
Drive A 1.44M, 3.5 in. <Month>
Drive B None Jan. to Dec.
Floppy 3 Mode Support Disabled
<Day>
Halt On All, But Keyboard 1 to 31 (or maximum
allowed in the month)
Base Memory 640K
Extended Memory 130048K <Year>
Total Memory 131072K 1999 to 2098
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 2: Standard CMOS Features
!!
!!
! Date
The date format is <week>, <month>, <day>, <year>.
!Week The week, from Sun to Sat, determined by the BIOS and is display only
!Month The month, Jan. Through Dec.
!Day The day, from 1 to 31 (or the maximum allowed in the month)
!Year The year, from 1999 through 2098
- 25 - BIOS Setup
!!
!!
! Time
The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour military-
time clock. For example, 1 p.m. is 13:00:00.
English
!!
!!
! IDE Primary Master, Slave / IDE Secondary Master, Slave
The category identifies the types of hard disk from drive C to F that has been installed in the computer.
There are two types: auto type, and manual type. Manual type is user-definable; Auto type which will
automatically detect HDD type.
Note that the specifications of your drive must match with the drive table. The hard disk will not work
properly if you enter improper information for this category.
If you select User Type, related information will be asked to enter to the following items. Enter the
information directly from the keyboard and press <Enter>. Such information should be provided in the
documentation form your hard disk vendor or the system manufacturer.
!CYLS. Number of cylinders
!HEADS Number of heads
!PRECOMP Write precomp
!LANDZONE Landing zone
!SECTORSNumber of sectors
If a hard disk has not been installed select NONE and press <Enter>.
!!
!!
! Drive A / Drive B
The category identifies the types of floppy disk drive A or drive B that has been installed in the
computer.
!None No floppy drive installed
!360K, 5.25 in. 5.25 inch PC-type standard drive; 360K byte capacity.
!1.2M, 5.25 in. 5.25 inch AT-type high-density drive; 1.2M byte capacity
(3.5 inch when 3 Mode is Enabled).
!720K, 3.5 in. 3.5 inch double-sided drive; 720K byte capacity
!1.44M, 3.5 in. 3.5 inch double-sided drive; 1.44M byte capacity.
!2.88M, 3.5 in. 3.5 inch double-sided drive; 2.88M byte capacity.
- 26 -GA-8ILMT4 Motherboard
English
!!
!!
! Floppy 3 Mode Support (for Japan Area)
!Disabled Normal Floppy Drive. (Default value)
!Drive A Drive A is 3 mode Floppy Drive.
!Drive B Drive B is 3 mode Floppy Drive.
!Both Drive A & B are 3 mode Floppy Drives.
!!
!!
!Halt on
The category determines whether the computer will stop if an error is detected during power up.
!NO Errors The system boot will not stop for any error that may be detected
and you will be prompted.
!All Errors Whenever the BIOS detects a non-fatal error the system will be stopped.
!All, But Keyboard The system boot will not stop for a keyboard error; it will stop for
all other errors. (Default value)
!All, But Diskette The system boot will not stop for a disk error; it will stop for all
other errors.
!All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will
stop for all other errors.
!!
!!
! Memory
The category is display-only which is determined by POST (Power On Self Test) of the BIOS.
Base Memory
The POST of the BIOS will determine the amount of base (or conventional)
memory installed in the system.
The value of the base memory is typically 512 K for systems with 512 K
memory installed on the motherboard, or 640 K for systems with 640 K or
more memory installed on the motherboard.
Extended Memory
The BIOS determines how much extended memory is present during the
POST.
This is the amount of memory located above 1 MB in the CPU’s memory
address map.
- 27 - BIOS Setup
Advanced BIOS Features
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
Advanced BIOS Features
English
First Boot Device Floppy Item Help
Second Boot Device HDD-0 Menu Level &
Third Boot Device CDROM
Boot Up Floppy Seek Disabled
Init Display First Onboard/AGP
Graphics Aperture Size 128MB
Graphics Share Memory 8MB
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 3: Advanced BIOS Features
! First / Second / Third Boot Device
!!
!!
! Floppy Select your boot device priority by Floppy.
!LS120 Select your boot device priority by LS120.
!HDD-0~3 Select your boot device priority by HDD-0~3.
!SCSI Select your boot device priority by SCSI.
!CDROM Select your boot device priority by CDROM.
!ZIP Select your boot device priority by ZIP.
!USB-FDD Select your boot device priority by USB-FDD.
!USB-ZIP Select your boot device priority by USB-ZIP.
!USB-CDROM Select your boot device priority by USB-CDROM.
!USB-HDD Select your boot device priority by USB-HDD.
!LAN Select your boot device priority by LAN.
!Disabled Select your boot device priority by Disabled.
- 28 -GA-8ILMT4 Motherboard
English
!!
!!
! Boot Up Floppy Seek
During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360 K type is
40 tracks 720 K, 1.2 M and 1.44 M are all 80 tracks.
!Enabled BIOS searches for floppy disk drive to determine it is 40 or 80 tracks. Note
that BIOS can not tell from 720 K, 1.2 M or 1.44 M drive type as they are
all 80tracks.
!Disabled BIOS will not search for the type of floppy disk drive by track number. Note
that there will not be any warning message if the drive installed is 360 K.
(Default value)
!!
!Init Display First
!!
!Onboard/AGP Set Init Display First to onboard/AGP. (Default value)
!PCI Set Init Display First to PCI.
!!
!!
!Graphics Aperture Size
!128MB Set Graphics Aperture Size to 128MB. (Default value)
!Disabled Disable this function.
!!
!!
!Graphics Share Memory
!8MB Set Graphics Share Memory to 8MB. (Default value)
!1MB Set Graphics Share Memory to 1MB.
- 29 - BIOS Setup
Integrated Peripherals
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
Integrated Peripherals
English
On-Chip Primary PCI IDE Enabled Item Help
On-Chip Secondary PCI IDE Enabled Menu Level &
IDE1 Conductor Cable Auto If a hard disk
IDE2 Conductor Cable Auto controller card is
USB Controller Enabled used, set at Disable
USB Keyboard Support Disabled
USB Mouse Support Disabled [Enabled]
AC97 Audio Auto Enable onboard IDE
Onboard LAN Enabled PORT
Onboard LAN Boot ROM Disabled
Onboard Serial Port 1 3F8/IRQ4
Onboard Serial Port 2 2F8/IRQ3
UART Mode Select Normal
x UR2 Duplex Mode Half [Disabled]
Onboard Parallel Port 378/IRQ7 Disable onboard IDE
Parallel Port Mode SPP PORT
Game Port Address 201
Midi Port Address 330
Midi Port IRQ 10
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 4: Integrated Peripherals
!!
!!
! On-Chip Primary PCI IDE
!Enabled Enable onboard 1st channel IDE port. (Default value)
!Disabled Disable onboard 1st channel IDE port.
- 30 -GA-8ILMT4 Motherboard
English
!!
!!
! On-Chip Secondary PCI IDE
!Enabled Enable onboard 2nd channel IDE port. (Default value)
!Disabled Disable onboard 2nd channel IDE port.
! IDE1 Conductor Cable
!!
!!
!Auto Will be automatically detected by BIOS. (Default Value)
!ATA66/100 Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE device
and cable is compatible with ATA66/100).
!ATA33 Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and
cable is compatible with ATA33).
!!
! IDE2 Conductor Cable
!!
!Auto Will be automatically detected by BIOS. (Default Value)
!ATA66/100 Set IDE2 Conductor Cable to ATA66/100 (Please make sure your IDE device
and cable is compatible with ATA66/100).
!ATA33 Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and
cable is compatible with ATA33).
!!
!!
! USB Controller
!Enabled Enable USB Controller. (Default value)
!Disabled Disable USB Controller.
!!
!!
! USB Keyboard Support
!Enabled Enable USB Keyboard Support.
!Disabled Disable USB Keyboard Support. (Default value)
!!
! USB Mouse Support
!!
!Enabled Enable USB Mouse Support.
!Disabled Disable USB Mouse Support. (Default value)
- 31 - BIOS Setup
!!
!!
! AC97 Audio
!Auto Enable onboard AC'97 audio function. (Default Value)
!Disabled Disable this function.
English
!!
! Onboard LAN
!!
!Enabled Enabled Onboard LAN function. (Default value)
!Disabled Disabled onboard LAN function.
!!
!!
! Onboard LAN Boot ROM
!Enabled Enabled Onboard LAN Boot ROM function.
!Disabled Disabled onboard LAN Boot ROM function.(Default value)
!!
! Onboard Serial Port 1
!!
!Auto BIOS will automatically setup the port 1 address.
!3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8. (Default value)
!2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8.
!3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8.
!2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8.
!Disabled Disable onboard Serial port 1.
!!
!!
! Onboard Serial Port 2
!Auto BIOS will automatically setup the port 2 address.
!3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8.
!2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8. (Default value)
!3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8.
!2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8.
!Disabled Disable onboard Serial port 2.
!!
!!
! UART Mode Select
(This item allows you to determine which Infra Red(IR) function of Onboard I/O chip)
!ASKIR Set onboard I/O chip UART to ASKIR Mode.
!IrDA Set onboard I/O chip UART to IrDA Mode.
!Normal Set onboard I/O chip UART to Normal Mode. (Default Value)
- 32 -GA-8ILMT4 Motherboard
English
!!
!!
! UR2 Duplex Mode
!Half IR Function Duplex Half. (Default Value)
!Full IR Function Duplex Full.
! Onboard Serial Port 2
!!
!!
!Auto BIOS will automatically setup the port 2 address.
!3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8.
!2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8. (Default value)
!3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8.
!2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8.
!Disabled Disable onboard Serial port 2.
! UART Mode Select
!!
!!
(This item allows you to determine which Infra Red(IR) function of Onboard I/O chip)
!ASKIR Set onboard I/O chip UART to ASKIR Mode.
!IrDA Set onboard I/O chip UART to IrDA Mode.
!Normal Set onboard I/O chip UART to Normal Mode. (Default Value)
!!
!!
! UR2 Duplex Mode
!Half IR Function Duplex Half. (Default Value)
!Full IR Function Duplex Full.
! Onboard Parallel port
!!
!!
!378/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default Value)
!278/IRQ5 Enable onboard LPT port and address is 278/IRQ5.
!Disabled Disable onboard LPT port.
!3BC/IRQ7 Enable onboard LPT port and address is 3BC/IRQ7.
!!
!!
!Parallel Port Mode
!SPP Using Parallel port as Standard Parallel Port. (Default Value)
!EPP Using Parallel port as Enhanced Parallel Port.
!ECP Using Parallel port as Extended Capabilities Port.
!ECP+EPP Using Parallel port as ECP & EPP mode.
- 33 - BIOS Setup
!!
!!
!ECP Mode Use DMA
!3 Set ECP Mode Use DMA to 3. (Default Value)
!1 Set ECP Mode Use DMA to 1.
English
!!
!!
!Game Port Address
!201 Set Game Port Address to 201. (Default Value)
!209 Set Game Port Address to 209.
!Disabled Disable this function.
!!
!!
!Midi Port Address
!300 Set Midi Port Address to 300.
!330 Set Midi Port Address to 330.(Default Value)
!Disabled Disable this function.
!!
!!
!Midi Port IRQ
!5 Set Midi Port IRQ to 5.
!10 Set Midi Port IRQ to 10. (Default Value)
- 34 -GA-8ILMT4 Motherboard
English
Power Management Setup
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
Power Management Setup
ACPI Suspend Type S1(POS) Item Help
Power LED in S1 State
Soft-Off by PWR_BTTN Instant-Off Menu Level &
PME Event Wake Up Enabled [S1]
ModemRingOn/WakeOnLan Enabled
Resume by Alarm Disabled Set suspend type to
x Date (of Month) Alarm Everyday Power On Suspend under
x Time (hh:nn:ss) Alarm 0 0 0 ACPI OS
Power On By Mouse Disabled
Power On By Keyboard Disabled [S3]
x KB Power ON Password Enter Set suspend type to
AC Back Function Soft-Off Suspend to RAM under
ACPI OS
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 5: Power Management Setup
!!
!!
! ACPI Suspend Type
This option will not be shown or not be available if you are using a CPU with the locked ratio.
!S1(POS) Set ACPI suspend type to S1. (Default Value)
!S3(STR) Set ACPI suspend type to S3.
!!
!!
! Power LED in S1 State
!Blinking In standby mode(S1), power LED will blink. (Default Value)
!Dual/Off In standby mode(S1):
a. If use single color LED, power LED will turn off.
b. If use dual color LED, power LED will turn to another color.
- 35 - BIOS Setup
!!
!!
! Soft-off by PWR_BTTN
!Instant-off Press power button then Power off instantly. (Default value)
English
!Delay 4 Sec. Press power button 4 sec to Power off. Enter suspend if button is pressed less
than 4 sec.
!!
! PME Event Wake Up
!!
!Disabled Disable this function.
!Enabled Enable PME Event Wake up. (Default Value)
!!
!!
! ModemRingOn/WakeOnLAN
!Disabled Disable Modem Ring on/wake on Lan function.
!Enabled Enable Modem Ring on/wake on Lan. (Default Value)
!!
! Resume by Alarm
!!
You can set "Resume by Alarm" item to enabled and key in Data/time to power on system.
!Disabled Disable this function. (Default Value)
!Enabled Enable alarm function to POWER ON system.
If RTC Alarm Lead To Power On is Enabled.
Date ( of Month) Alarm : Everyday, 1~31
Time ( hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59)
!!
!!
! Power On By Mouse
!Disabled Disabled this function. (Default value)
!Mouse Click Double click on PS/2 mouse left button.
!!
!!
! Power On By Keyboard
!Password Enter from 1 to 5 characters to set the Keyboard Power On Password.
!Disabled Disabled this function. (Default value)
!Keyboard 98 If your keyboard have “POWER Key” button, you can press the key to
power on your system.
- 36 -GA-8ILMT4 Motherboard
English
!!
!!
!KB Power ON Password
!Enter Input password (from 1 to 5 characters) and press Enter to set the Key
board Power On Password.
!!
!!
!AC Back Function
! Memory System power on depends on the status before AC lost.
!Soft-Off Always in Off state when AC back. (Default value)
!Full-On Always power on the system when AC back.
- 37 - BIOS Setup
PnP/PCI Configurations
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
PnP/PCI Configurations
English
PCI 1 IRQ Assignment Auto Item Help
PCI 2 IRQ Assignment Auto Menu Level &
PCI 3 IRQ Assignment Auto
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 6: PnP/PCI Configurations
!!
! PCI 1 IRQ Assignment
!!
!Auto Auto assign IRQ to PCI. (Default value)
!3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1/PCI 5.
!!
! PCI 2 IRQ Assignment
!!
!Auto Auto assign IRQ to PCI 2. (Default value)
!3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.
! PCI 3 IRQ Assignment
!!
!!
!Auto Auto assign IRQ to PCI 3. (Default value)
!3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 3.
- 38 -GA-8ILMT4 Motherboard
English
PC Health Status
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
PC Health Status
Reset Case Open Status Disabled Item Help
Case Opened No Menu Level &
VCORE 1.730V
+1.5V 1.502V
+3.3V 3.360V
+5V 5.053V
+12V 11.840V
Current CPU Temperature 35°C/95°F
Current CPU FAN Speed 6490 RPM
Current SYSTEM FAN Speed 0 RPM
CPU Warning Temperature Disabled
CPU FAN Fail Warning Disabled
SYSTEM FAN Fail Warning Disabled
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 7: PC Health Status
!Reset Case Open Status
!!
!!
!!
!Case Opened
!!
If the case is closed, "Case Opened" will show "No".
If the case have been opened, "Case Opened" will show "Yes".
If you want to reset "Case Opened" value, set "Reset Case Open Status" to
"Enabled" and save CMOS, your computer will restart.
Disabled : Don’t reset case open status.;Enabled : Clear case open status at next boot.
!!
!!
! Current Voltage (V) VCORE / 1.5V /+3.3V / +5V / +12V
!Detect system’s voltage status automatically.
- 39 - BIOS Setup
!!
!!
!Current CPU Temperature
!Detect CPU Temp. automatically.
English
!!
!!
! Current CPU/SYSTEM FAN Speed (RPM)
!Detect CPU/SYSTEM Fan speed status automatically.
!!
!!
! CPU Warning Temperature
!60°C / 140°F Monitor CPU Temp. at 60°C / 140°F.
!70°C / 158°F Monitor CPU Temp. at 70°C / 158°F.
!80°C / 176°F Monitor CPU Temp. at 80°C / 176°F.
!90°C / 194°F Monitor CPU Temp. at 90°C / 194°F.
!Disabled Disable this function.(Default value)
!!
!!
! CPU FAN Fail Warning
!Disabled Fan Warning Function Disable. (Default value)
!Enabled Fan Warning Function Enable.
!!
!!
! SYSTEM FAN Fail Warning
!Disabled Fan Warning Function Disable. (Default value)
!Enabled Fan Warning Function Enable.
- 40 -GA-8ILMT4 Motherboard
English
Frequency/Voltage Control
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
Frequency/Voltage Control
CPU Clock Ratio 15X Item Help
CPU Host Clock Control Disabled Menu Level &
x CPU Host Frequency (Mhz) 100
x PCI/AGP Divider Disabled
Host/DRAM Clock ratio Auto
Memory Frequency (Mhz) 266
PCI/AGP Frequency (Mhz) 33/66
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 7: Frequency/Voltage Control
!CPU Clock Ratio
!!
!!
This option will not be shown or not be available if you are using a CPU with the locked ratio.
!10X~24X It’s depends on CPU Clock Ratio.
!!
!!
!CPU Host Clock Control
Note: If system hangs up before enter CMOS setup utility, wait for 20 sec for times out reboot . When
time out occur, system will reset and run at CPU default Host clock at next boot.
!Disable Disable CPU Host Clock Control.(Default value)
!Enable Enable CPU Host Clock Control.
!CPU Host Frequency
!!
!!
!100MHz ~ 355MHz Set CPU Host Clock from 100MHz to 355MHz.
- 41 - BIOS Setup
!!
!!
!PCI/AGP Divider
!You can choose Disabled,PLL/40,PLL/32,PLL/24,PLL/20/PLL/16 mode to adjust PCI/AGP
frequency.
English
!!
!!
!Host/DRAM Clock Ratio
(Warning: wrong frequency may make system can’t boot, clear CMOS to overcome wrong fre
quency issue)
!2.0 Memory Frequency = Host clock X 2.0.
!2.66 Memory Frequency = Host clock X 2.66.
!Auto Set Memory frequency by DRAM SPD data. (Default value)
!!
!!
! Memory Frequency(Mhz)
!The values depend on CPU Host Frequency(Mhz) .
! PCI/AGP Frequency(Mhz)
!!
!!
!Setup PCI/AGP frequency by adjusting CPU Host Frequency or PCI/AGP Divider item.
- 42 -GA-8ILMT4 Motherboard
English
Top Performance
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features Load Fail-Safe Defaults
!Advanced BIOS Features Load Optimized Defaults
Top Performance
!Integrated Peripherals Set Supervisor Password
!Power Management Setup Set User Password
Disabled...................[ &]
!PnP/PCI Configurations Save & Exit Setup
Enabled................... [ ]
!Frequency/Voltage Control Exit Without Saving
Top Performance
"#: Move ENTER: Accept
ESC: Abort
ESC:Quit F3: Select Language
F8: Q-Flash F10:Save & Exit Setup
Figure 8: Top Performance
Top Performance
If you wish to maximize the performance of your system, set "Top Performance" as "Enabled".
!Disabled Disable this function. (Default Value)
!Enabled Enable Top Performance function.
- 43 - BIOS Setup
Load Fail-Safe Defaults
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features Top Performance
English
!Advanced Chipset Features Load Fail-Safe Defaults
!Integrated Peripherals Load Optimized Defaults
!Power Management Setup Set Supervisor Password
Load Fail-Safe Defaults? (Y/N)?Y
!PnP/PCI Configurations Set User Password
!PC Health Status Save & Exit Setup
!Frequency/Voltage Control Exit Without Saving
ESC:Quit "#$%:Select Item
F8: Q-Flash F10:Save & Exit Setup
Load Fail-Safe Defaults
Figure 10: Load Fail-Safe Defaults
Load Fail-Safe Defaults
Fail-Safe defaults contain the most appropriate values of the system parameters that allow
minimum system performance.
- 44 -GA-8ILMT4 Motherboard
English
Load Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features Top Performance
!Advanced BIOS Features Load Fail-Safe Defaults
!Integrated Peripherals Load Optimized Defaults
!Power Management Setup Set Supervisor Password
Load Optimized Defaults? (Y/N)?Y
!PnP/PCI Configurations Set User Password
!PC Health Status Save & Exit Setup
!Frequency/Voltage Control Exit Without Saving
ESC:Quit "#$%:Select Item
F8: Q-Flash F10:Save & Exit Setup
Load Optimized Defaults
Figure 11: Load Optimized Defaults
Load Optimized Defaults
Selecting this field loads the factory defaults for BIOS and Chipset Features which the
system automatically detects.
- 45 - BIOS Setup
Set Supervisor/User Password
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features Top Performance
English
!Advanced BIOS Features Load Fail-Safe Defaults
!Integrated Peripherals Load Optimized Defaults
!Power Management Setup Set Supervisor Password
Enter Password:
!PnP/PCI Configurations Set User Password
!PC Health Status Save & Exit Setup
!Frequency/Voltage Control Exit Without Saving
ESC:Quit "#$%:Select Item
F8: Q-Flash F10:Save & Exit Setup
Change/Set/Disable Password
Figure 12: Password Setting
When you select this function, the following message will appear at the center of the screen to assist
you in creating a password.
Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the
password. Type the password again and press <Enter>. You may also press <Esc> to abort the
selection and not enter a password.
To disable password, just press <Enter> when you are prompted to enter password. A message
“PASSWORD DISABLED” will appear to confirm the password being disabled. Once the password is
disabled, the system will boot and you can enter Setup freely.
The BIOS Setup program allows you to specify two separate passwords:
SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access
all BIOS Setup program function. When enabled, the Supervisor password is required for entering the
BIOS Setup program and having full configuration fields, the User password is required to access only
basic items.
If you select “System” at “Password Check” in Advance BIOS Features Menu, you will be
prompted for the password every time the system is rebooted or any time you try to enter Setup Menu.
If you select “Setup” at “Password Check” in Advance BIOS Features Menu, you will be prompted
only when you try to enter Setup.
- 46 -GA-8ILMT4 Motherboard
English
Save & Exit Setup
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features Top Performance
!Advanced BIOS Features Load Fail-Safe Defaults
!Integrated Peripherals Load Optimized Defaults
!Power Management Setup Set Supervisor Password
!PnP/PCI Configurations Set User Password
Save to CMOS and EXIT (Y/N)? Y
!PC Health Status Save & Exit Setup
!Frequency/Voltage Control Exit Without Saving
ESC:Quit "#$%:Select Item
F8: Q-Flash F10:Save & Exit Setup
Save Data to CMOS
Figure 13: Save & Exit Setup
Type “Y” will quit the Setup Utility and save the user setup value to RTC CMOS.
Type “N” will return to Setup Utility.
- 47 - BIOS Setup
Exit Without Saving
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features Top Performance
English
!Advanced BIOS Features Load Fail-Safe Defaults
!Integrated Peripherals Load Optimized Defaults
!Power Management Setup Set Supervisor Password
!PnP/PCI Configurations Set User Password
Quit Without Saving (Y/N)? N
!PC Health Status Save & Exit Setup
!Frequency/Voltage Control Exit Without Saving
ESC:Quit "#$%:Select Item
F8: Q-Flash F10:Save & Exit Setup
Abandon all Data
Figure 14: Exit Without Saving
Type “Y” will quit the Setup Utility without saving to RTC CMOS.
Type “N” will return to Setup Utility.
- 48 -GA-8ILMT4 Motherboard