Gigabyte GA-8IE2004: FAQ

FAQ

Below is a collection of general asked questions. To check general asked questions based on a

specific motherboard model, please log on to

http://tw.giga-byte.com/faq/faq.htm

English

Question 1: I cannot see some options that were included in previous BIOS after updating BIOS.

Why?

Answer: Some advanced options are hidden in new BIOS version. Please press Ctrl and F1 keys

after entering BIOS menu and you will be able to see these options.

Questions 2: Why is the light of my keyboard/optical mouse still on after computer shuts down?

Answer: In some boards, a small amount of electricity is kept on standby after computer shuts

down and that's why the light is still on.

™

Question 3: Why cannot I use all functions in EasyTune

4?

™

Answer: The availability of the listed functions in EasyTune

4 depends on the MB chipset. If the

™

chipset doesn't support certain functions in EasyTune

4, these functions will be locked automati-

cally and you will not be able to use them.

Question 4: Why do I fail to install RAID and ATA drivers under Win 2000 and XP on boards that

support RAID function after I connect the boot HDD to IDE3 or IDE4 ?

Answer: First of all, you need to save some files in the CD-ROM to a floppy disk before installing

drivers. You also need to go through some rather different steps in the installation process. Therefore,

we suggest that you refer to the installation steps in the RAID manual at our website.

(Please download it at

http://tw.giga-byte.com/support/user_pdf/raid_manual.pdf)

Question 5: How do I clear CMOS?

Answer: If your board has a Clear CMOS jumper, please refer to the Clear CMOS steps in the

manual. If your board doesn't have such jumper, you can take off the on-board battery to leak

voltage to clear CMOS. Please refer to the steps below:

Steps:

1. Turn off power.

2. Disconnect the power cord from MB.

3. Take out the battery gently and put it aside for about 10 minutes (Or you can use a

metal object to connect the positive and negative pins in the battery holder to make

them short for one minute).

4. Re-insert the battery to the battery holder.

5. Connect power cord to MB again and turn on power.

6. Press Del to enter BIOS and load Fail-Safe Defaults.

7. Save changes and reboot the system.

- 80 -GA-8IE2004 Series Motherboard

English

Question 6: Why does system seem unstable after updating BIOS?

Answer: Please remember to load Fail-Safe Defaults (Or Load BIOS Defaults) after flashing

BIOS. However, if the system instability still remains, please clear CMOS to solve the problem.

Question 7: Why do I still get a weak sound after turning up the speaker to the maximum volume?

Answer: Please make sure the speaker you are using is equipped with an internal amplifier. If not,

please change another speaker with power/amplifier and try again later.

Question 8: How do I disable onboard VGA card in order to add an external VGA card?

Answer: Gigabyte motherboards will auto-detect the external VGA card after it is plugged in, so

you don't need to change any setting manually to disable the onboard VGA.

Question 9: Why cannot I use the IDE 2?

Answer: Please refer to the user manual and check whether you have connected any cable that

is not provided with the motherboard package to the USB Over Current pin in the Front USB

Panel. If the cable is your own cable, please remove it from this pin and do not connect any of your

own cables to it.

Question 10: Sometimes I hear different continuous beeps from computer after system boots up.

What do these beeps usually stand for?

Answer: The beep codes below may help you identify the possible computer problems. However,

they are only for reference purposes. The situations might differ from case to case.

JAMI BIOS Beep Codes

J AWARD BIOS Beep Codes

*Computer gives 1 short beep when system boots successfully.

1 short: System boots successfully

*Except for beep code 8, these codes are always fatal.

2 short: CMOS setting error

1 beep Refresh failure

1 long 1 short: DRAM or M/B error

2 beeps Parity error

1 long 2 short: Monitor or display card error

3 beeps Base 64K memory failure

1 long 3 short: Keyboard error

4 beeps Timer not operational

1 long 9 short: BIOS ROM error

5 beeps Processor error

Continuous long beeps: DRAM error

6 beeps 8042 - gate A20 failure

Continuous short beeps: Power error

7 beeps Processor exception interrupt error

8 beeps Display memory read/write failure

9 beeps ROM checksum error

10 beeps CMOS shutdown register read/write error

11 beeps Cache memory bad

Appendix- 81 -

Question 11: How to set in the BIOS in order to bootup from SATA HDDs by either RAID or ATA

mode?

Answer: Please set in the BIOS as follow:

1. Advanced BIOS features--> SATA/RAID/SCSI boot order: "SATA"

English

2. Advanced BIOS features--> First boot device: "SCSI"

3. Integrated Peripherals--> Onboard H/W Serial ATA: "enable"

Then it depends on the SATA mode that you need to set "RAID" to RAID mode or "BASE" to

normal ATA mode in the item named Serial ATA function.

Question 12: For the M/B which have RAID function, how to set in the BIOS in order to bootup

from IDE3, 4 by either RAID or ATA mode?

Answer: Please set in the BIOS as follow:

1. Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SATA"

2. Advanced BIOS features--> First boot device: "SCSI"

3. Integrated Peripherals--> Onboard H/W ATA/RAID: "enable"

Then it depends on the RAID mode that you need to set "RAID" to RAID mode or "ATA" to normal

ATA mode in the item named RAID controller function.

Question 13: How to set in the BIOS to bootup from the IDE/ SCSI/ RAID card ?

Answer: Please set in the BIOS as follow:

1. Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SCSI"

2. Advanced BIOS features--> First boot device: "SCSI"

Then it depends on the mode(RAID or ATA) that you need to set in RAID/ SCSI BIOS.

- 82 -GA-8IE2004 Series Motherboard