Gigabyte GA-8I845GVM-775: Chapter 4 Appendix

4-1-2 Xpress Recovery Introduction

What is Xpress Recovery ?

Xpress Recovery is a utility used to back up and restore an OS partition.

English

If the hard drive is not working properly, the user can restore the drive to

its original state.

1. Supports FAT16, FAT32, and NTFS formats

2. Must be connected to the IDE1 Master

3. Allows installation of only one OS

4. Must be used with an IDE hard disk supporting HPA

5. The first partition must be set as the boot partition. When the boot partition is backed up,

please do not alter its size.

6. Xpress Recovery is recommended when using Ghost to return boot manager to NTFS

format.

How to use the Xpress Recovery

1. Boot from CD-ROM (BMP Mode)

Enter the BIOS menu, select "Advanced BIOS Feature" and set to boot from CD-ROM. Insert the

provided driver CD into your CD drive, then save and exit the BIOS menu. Once the computer has

restarted, the phrase "Boot from CD:" will appear at the bottom left-hand corner of the screen. When

"Boot from CD:" appears, press any key to enter Xpress Recovery.

Once you have completed this step, subsequent access to Xpress Recovery can also function by

pressing the F9 key during computer power on.

.

.

Verifying DMI Pool Data

Boot from CD:

Boot from CD:

Xpress Recovery V1.0 (C) Copy Right 2003. GIGABYTE Technology CO. , Ltd.

1. Execute Backup Utility

2. Execute Restore Utility

3. Remove Backup Image

4. Set Password

5. Exit and Restart

Build 2011

GA-8I845GVM775 Motherboard - 48 -

2. Press F9 during powering on the computer. (Text Mode)

English

Press F9 during powering on the computer .

Award Modular BIOS v6.00PG, An Energy Star Ally

Copyright (C) 1984-2004, Award Software, Inc.

Intel 865PE AGPSet BIOS for 8IPE1000MT F1

Check System Health OK

.

.

.

Press DEL to enter SETUP / Q-Flash, F9 For Xpress Recovery

F9 For Xpress Recovery

08/16/2002-I845GE-6A69YG01C-00

Xpress Recovery V1.0 (C) Copy Right 2003. GIGABYTE Technology CO. , Ltd.

1. Execute Backup Utility

2. Execute Restore Utility

3. Remove Backup Image

4. Set Password

5. Exit and Restart

1. If you have already entered Xpress Recovery by booting from the CD-ROM, you can

enter Xpress Recovery in the future by pressing the F9 key.

2. System storage capacity as well as drive reading/writing speed will affect backup speed.

3. It is recommended that Xpress Recovery be immediately installed after OS and all

required driver and software installations are complete.

Appendix- 49 -

1. Execute Backup Utility:





 Press B to Backup your System or Esc to Exit

The backup utility will automatically scan your system and back up data as a backup image in your hard

English

drive.

Not all systems support access to Xpress Recovery by pressing the F9 key during computer

power on. If this is the case, please use the boot from CD-ROM method to enter Xpress

Recovery.

2. Execute Restore Utility:





 This program will recover your system to factory default.

Press R to restore your system back to factory default or press Esc to exit

Restores backup image to original state.

3. Remove Backup Image:





 Remove backup image. Are you sure? (Y/N)

Remove the backup image.

4. Set Password:





 Please input a 4-16 character long password (a-z or 0-9) or press Esc to exit

You can set a password to enter Xpress Recovery to protect your hard disk data. Once this is done,

password input will be required to enter Xpress Recovery during the next as well as subsequent system

restarts. If you wish to remove the need for password entry, please select "Set Password" and under

"New Password/Confirm Password", make sure there is no entry and then press "Enter" to remove

password requirement.

5. Exit and Restart:

Exit and restart your computer.

GA-8I845GVM775 Motherboard - 50 -

English

4-1-3 Flash BIOS Method Introduction

TM

Method 1 : Q-Flash

Utility

Q-Flash

TM

is a BIOS flash utility embedded in Flash ROM. With this utility,

users only have to stay in the BIOS menu when they want to update

BIOS. Q-Flash?allows users to flash BIOS without any utility in DOS or

Windows. Using Q-Flash

TM

indicating no more fooling around with any complicated instructions and

operating system since it is in the BIOS menu.

Please note that because updating BIOS has potential risk, please do it with caution!! We are

sorry that Gigabyte Technology Co., Ltd is not responsible for damages of system because of

incorrect manipulation of updating BIOS to avoid any claims from end-users.

Before You Begin:

Before you start updating BIOS with the Q-Flash

TM

utility, please follow the steps below first.

1. Download the latest BIOS for your motherboard from Gigabyte's website.

2. Extract the BIOS file downloaded and save the BIOS file (the one with model name.Fxx. For

example, 8KNXPU.Fba) to a floppy disk.

3. Reboot your PC and press Del to enter BIOS menu.

The BIOS upgrading guides below are separated into two parts.

If your motherboard has dual-BIOS, please refer to Part One.

If your motherboard has single-BIOS, please refer to Part Two.

Part One:

TM

Updating BIOS with Q-Flash

Utility on Dual BIOS Motherboards.

Some of Gigabyte motherboards are equipped with dual BIOS. In the BIOS menu of the motherboards

supporting Q-Flash and Dual BIOS, the Q-Flash utility and Dual BIOS utility are combined in the same

screen. This section only deals with how to use Q-Flash utility.

In the following sections, we take GA-8KNXP Ultra as the example to guide you how to flash BIOS

from an older version to the latest version. For example, from Fa3 to Fba.

Award Modular BIOS v6.00PG, An Energy Star Ally

Copyright (C) 1984-2003, Award Software, Inc.

Intel i875P AGPset BIOS for 8KNXP Ultra Fa3

The BIOS file is Fa3

Check System Health OK , VCore = 1.5250

Main Processor : Intel Pentium(R) 4 1.6GHz (133x12)

before updating

<CPUID : 0F27 Patch ID : 0027>

Memory Testing : 131072K OK

Memory Frequency 266 MHz in Single Channel

Primary Master : FUJITSU MPE3170AT ED-03-08

Primary Slave : None

Secondary Master : CREATIVEDVD-RM DVD1242E BC101

Secondary Slave : None

Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 For

Xpress Recovery

08/07/2003-i875P-6A79BG03C-00

Appendix- 51 -

TM

Entering the Q-Flash

utility:

Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

English

 Standard CMOS Features

Select Language

 Advanced BIOS Features

Load Fail-Safe Defaults

 Integrated Peripherals

Load Optimized Defaults

 Power Management Setup

Set Supervisor Password

 PnP/PCI Configurations

Set User Password

 PC Health Status

Save & Exit Setup

 MB Intelligent Tweaker(M.I.T.)

Exit Without Saving

ESC: Quit F3: Change Language

F8: Dual BIOS/Q-Flash F10: Save & Exit Setup

Time, Date, Hard Disk Type...

Step 2: Press F8 button on your keyboard and then Y button to enter the Dual BIOS/Q-Flash utility.

TM

Exploring the Q-Flash

/ Dual BIOS utility screen

The Q-Flash / Dual BIOS utility screen consists of the following key components.

Dual BIOS Utility

Boot From......................................... Main Bios

Dual BIOS utility bar

Main ROM Type/Size.............................SST 49LF003A 512K

Backup ROM Type/Size.........................SST 49LF003A 512K

Task menu for

Wide Range Protection Disable

Dual BIOS

Boot From Main Bios

Auto Recovery Enable

utility

Halt On Error Disable

Copy Main ROM Data to Backup

Load Default Settings

Save Settings to CMOS

Q-Flash Utility

Load Main BIOS from Floppy

Q-Flash

TM

utility title

Task menu for

Load Backup BIOS from Floppy

bar

Q-Flash

TM

utility

Save Main BIOS to Floppy

Save Backup BIOS to Floppy

Enter : Run :Move ESC:Reset F10:Power Off

Action bar

Task menu for Dual BIOS utility:

Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking a

task and pressing Enter key on your keyboard to enable execution of the task.

Task menu for Q-Flash utility:

Contains the names of four tasks. Blocking a task and pressing Enter key on your keyboard to enable execu-

tion of the task.

Action bar:

Contains the names of four actions needed to operate the Q-Flash/Dual BIOS utility. Pressing the buttons

mentioned on your keyboards to perform these actions.

GA-8I845GVM775 Motherboard - 52 -

TM

Using the Q-Flash

utility:

English

This section tells you how to update BIOS using the Q-Flash utility. As described in the "Before you begin"

section above, you must prepare a floppy disk having the BIOS file for your motherboard and insert it to your

computer. If you have already put the floppy disk into your system and have entered the Q-Flash utility,

please follow the steps below to flash BIOS.

Steps:

1. Press arrow buttons on your keyboard to move the light bar to "Load Main BIOS from Floppy" item in

the Q-Flash menu and press Enter button.

Later, you will see a box pop up showing the BIOS files you previously downloaded to the floppy disk.

If you want to save the current BIOS for backup purpose, you can begin Step 1 with "Save Main

BIOS to Floppy" item.

2. Move to the BIOS file you want to flash and press Enter.

In this example, we only download one BIOS file to the floppy disk so only one BIOS file,

8KNXPU.Fba, is listed.

Please confirm again you have the correct BIOS file for your motherboard.

Dual BIOS Utility

Boot From......................................... Main Bios

Main ROM Type/Size.............................SST 49LF003A 512K

Backup ROM Type/Size.........................SST 49LF003A 512K

Wide Range Protection Disable

Boot From Main Bios

1 file(s) found

8KNXPU.Fba 512K

BIOS file in the floppy

Auto Recovery Enable

Halt On Error Disable

disk.

Copy Main ROM Data to Backup

Total size : 1.39M Free size : 911.50K

F5 : Refresh DEL : Delete

Load Default Settings

Save Settings to CMOS

Q-Flash Utility

Load Main BIOS from Floppy

Load Backup BIOS from Floppy

Save Main BIOS to Floppy

Save Backup BIOS to Floppy

Enter : Run :Move ESC:Reset F10:Power Off

After pressing Enter, you'll then see the progress of reading the BIOS file from the floppy disk.

Dual BIOS Utility

Boot From......................................... Main Bios

Main ROM Type/Size.............................SST 49LF003A 512K

Backup ROM Type/Size.........................SST 49LF003A 512K

Wide Range Protection Disable

Boot From Main Bios

Reading BIOS file from floppy ...

Auto Recovery Enable

Do not trun off power or

>>>>>>>>>>>>>>.....................

Halt On Error Disable

reset your system at this

Copy Main ROM Data to Backup

Don't Turn Off Power or Reset System

Load Default Settings

stage!!

Save Settings to CMOS

Q-Flash Utility

Load Main BIOS from Floppy

Load Backup BIOS from Floppy

Save Main BIOS to Floppy

Save Backup BIOS to Floppy

Enter : Run :Move ESC:Reset F10:Power Off

After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?"

Appendix- 53 -

3. Press Y button on your keyboard after you are sure to update BIOS.

Then it will begin to update BIOS. The progress of updating BIOS will be displayed.

Please do not take out the floppy disk when it begins flashing BIOS.

English

4. Press any keys to return to the Q-Flash menu when the BIOS updating procedure is completed.

Dual BIOS Utility

Boot From......................................... Main Bios

Main ROM Type/Size.............................SST 49LF003A 512K

Backup ROM Type/Size.........................SST 49LF003A 512K

Wide Range Protection Disable

You can repeat Step 1 to

Boot From Main Bios

!! Copy BIOS completed - Pass !!

Auto Recovery Enable

4 to flash the backup

Halt On Error Disable

BIOS, too.

Copy Main ROM Data to Backup

Please press any key to continue

Load Default Settings

Save Settings to CMOS

Q-Flash Utility

Load Main BIOS from Floppy

Load Backup BIOS from Floppy

Save Main BIOS to Floppy

Save Backup BIOS to Floppy

Enter : Run :Move ESC:Reset F10:Power Off

5. Press Esc and then Y button to exit the Q-Flash utility. The computer will restart automatically after

you exit Q-Flash.

Dual BIOS Utility

Boot From......................................... Main Bios

Main ROM Type/Size.............................SST 49LF003A 512K

Backup ROM Type/Size.........................SST 49LF003A 512K

Wide Range Protection Disable

Boot From Main Bios

Auto Recovery Enable

Are you sure to RESET ?

Halt On Error Disable

Copy Main ROM Data to Backup

[Enter] to continure or [Esc] to abort...

Load Default Settings

Save Settings to CMOS

Q-Flash Utility

Load Main BIOS from Floppy

Load Backup BIOS from Floppy

Save Main BIOS to Floppy

Save Backup BIOS to Floppy

Enter : Run :Move ESC:Reset F10:Power Off

After system reboots, you may find the BIOS version on your boot screen becomes the one you flashed.

Award Modular BIOS v6.00PG, An Energy Star Ally

Copyright (C) 1984-2003, Award Software, Inc.

The BIOS file

Intel i875P AGPset BIOS for 8KNXP Ultra Fba

Check System Health OK , VCore = 1.5250

becomes Fab after

Main Processor : Intel Pentium(R) 4 1.6GHz (133x12)

<CPUID : 0F27 Patch ID : 0027>

updating.

Memory Testing : 131072K OK

Memory Frequency 266 MHz in Single Channel

Primary Master : FUJITSU MPE3170AT ED-03-08

Primary Slave : None

Secondary Master : CREATIVEDVD-RM DVD1242E BC101

Secondary Slave : None

Press DEL to enter SETUP / Dual BIOS / Q-Flash / F9 For

Xpress Recovery

09/23/2003-i875P-6A79BG03C-00

GA-8I845GVM775 Motherboard - 54 -

6. Press Del to enter BIOS menu after system reboots. When you are in BIOS menu, move to

English

Load Fail-Safe Defaults item and press Enter to load BIOS Fail-Safe Defaults. Normally the system

redetects all devices after BIOS has been upgraded. Therefore, we highly recommend reloading the

BIOS defaults after BIOS has been upgraded.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

 Standard CMOS Features

Select Language

 Advanced BIOS Features

Load Fail-Safe Defaults

 Integrated Peripherals

Load Optimized Defaults

 Power Management Setup

Load Fail-Safe Defaults (Y/N)? Y

Set Supervisor Password

 PnP/PCI Configurations

Set User Password

 PC Health Status

Save & Exit Setup

 MB Intelligent Tweaker(M.I.T.)

Exit Without Saving

ESC: Quit F3: Change Language

F8: Dual BIOS/Q-Flash F10: Save & Exit Setup

Time, Date, Hard Disk Type...

Press Y on your keyboard to load defaults.

7. Select Save & Exit Setup item to save the settings to CMOS and exit the BIOS menu.

System will reboot after you exit the BIOS menu. The procedure is completed.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

 Standard CMOS Features

Select Language

 Advanced BIOS Features

Load Fail-Safe Defaults

 Integrated Peripherals

Load Optimized Defaults

 Power Management Setup

Save to CMOS and EXIT (Y/N)? Y

Set Supervisor Password

 PnP/PCI Configurations

Set User Password

 PC Health Status

Save & Exit Setup

 MB Intelligent Tweaker(M.I.T.)

Exit Without Saving

ESC: Quit F3: Change Language

F8: Dual BIOS/Q-Flash F10: Save & Exit Setup

Time, Date, Hard Disk Type...

Press Y on your keyboard to save and exit.

Part Two:

TM

Updating BIOS with Q-Flash

Utility on Single-BIOS Motherboards.

This part guides users of single-BIOS motherboards how to update BIOS using the Q-Flash

TM

utility.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

 Standard CMOS Features

Top Performance

 Advanced BIOS Features

Load Fail-Safe Defaults

 Integrated Peripherals

Load Optimized Defaults

 Power Management Setup

Set Supervisor Password

 PnP/PCI Configurations

Set User Password

 PC Health Status

Save & Exit Setup

 MB Intelligent Tweaker(M.I.T.)

Exit Without Saving

ESC: Quit F3: Change Language

F8: Q-Flash F10: Save & Exit Setup

Time, Date, Hard Disk Type...

Appendix- 55 -

TM

Exploring the Q-Flash

utility screen

The Q-FlashBIOS utility screen consists of the following key components.

TM

Q-Flash Utility V1.30

Q-Flash

utility bar

Flash Type/Size.................................SST 49LF003A 256K

English

Task menu for

Keep DMI Data Enable

Update BIOS from Floppy

Q-Flash

TM

utility

Save BIOS to Floppy

Enter : Run :Move ESC:Reset F10:Power Off

Action bar

Task menu for Q-Flash utility:

Contains the names of three tasks. Blocking a task and pressing Enter key on your keyboard to enable

execution of the task.

Action bar:

Contains the names of four actions needed to operate the Q-Flash utility. Pressing the buttons mentioned on

your keyboards to perform these actions.

TM

Using the Q-Flash

utility:

This section tells you how to update BIOS using the Q-Flash utility. As described in the "Before you begin"

section above, you must prepare a floppy disk having the BIOS file for your motherboard and insert it to your

computer. If you have already put the floppy disk into your system and have entered the Q-Flash utility,

please follow the steps below to flash BIOS.

Steps:

1. Press arrow buttons on your keyboard to move the light bar to "Update BIOS from Floppy" item in the

Q-Flash menu and press Enter button.

Later, you will see a box pop up showing the BIOS files you previously downloaded to the floppy disk.

If you want to save the current BIOS for backup purpose, you can begin Step 1 with "Save BIOS

to Floppy" item.

2. Move to the BIOS file you want to flash and press Enter.

In this example, we only download one BIOS file to the floppy disk so only one BIOS file,

8GE800.F4, is listed.

Please confirm again you have the correct BIOS file for your motherboard.

Q-Flash Utility V1.30

Flash Type/Size.................................SST 49LF003A 256K

1 file(s) found

8GE800.F4 256K

Keep DMI Data Enable

BIOS file in the floppy

Update BIOS from Floppy

disk.

Total size : 1.39M Free size : 1.14M

Save BIOS to Floppy

Enter : Run :Move ESC:Reset F10:Power Off

F5 : Refresh DEL : Delete

Q-Flash Utility V1.30

Flash Type/Size.................................SST 49LF003A 256K

Reading BIOS file from floppy ...

Keep DMI Data Enable

Do not trun off power or

>>>>>>>>>>>>>>.....................

Update BIOS from Floppy

Save BIOS to Floppy

reset your system at

Enter : Run :Move ESC:Reset F10:Power Off

Don't Turn Off Power or Reset System

this stage!!

After BIOS file is read, you'll see a confirmation dialog box asking you "Are you sure to update BIOS?"

Please do not take out the floppy disk when it begins flashing BIOS.

GA-8I845GVM775 Motherboard - 56 -

3. Press Y button on your keyboard after you are sure to update BIOS.

English

Then it will begin to update BIOS. The progress of updating BIOS will be shown at the same time.

Q-Flash Utility V1.30

Flash Type/Size.................................SST 49LF003A 256K

Keep DMI Data Enable

Updating BIOS Now

Do not trun off power or

>>>>>>>>>>>>>>>>>>>.........................

Update BIOS from Floppy

Save BIOS to Floppy

reset your system

Enter : Run :Move ESC:Reset F10:Power Off

Don't Turn Off Power or Reset System

at this stage!!

4. Press any keys to return to the Q-Flash menu when the BIOS updating procedure is completed.

Q-Flash Utility V1.30

Flash Type/Size.................................SST 49LF003A 256K

Keep DMI Data Enable

!! Copy BIOS completed - Pass !!

Update BIOS from Floppy

Save BIOS to Floppy

Please press any key to continue

Enter : Run :Move ESC:Reset F10:Power Off

5. Press Esc and then Y button to exit the Q-Flash utility. The computer will restart automatically after

you exit Q-Flash.

Q-Flash Utility V1.30

Flash Type/Size.................................SST 49LF003A 256K

Keep DMI Data Enable

Are you sure to RESET ?

Update BIOS from Floppy

Save BIOS to Floppy

[Enter] to continure or [Esc] to abort...

Enter : Run :Move ESC:Reset F10:Power Off

After system reboots, you may find the BIOS version on your boot screen becomes the one you flashed.

Award Modular BIOS v6.00PG, An Energy Star Ally

Copyright (C) 1984-2003, Award Software, Inc.

Intel 845GE AGPSet BIOS for 8GE800 F4

The BIOS file

Check System Health OK

Main Processor : Intel Pentium(R) 4 1.7GHz (100x17.0)

becomes F4 after

<CPUID : 0F0A Patch ID : 0009>

Memory Testing : 122880K OK + 8192K Shared Memory

updating

Primary Master : FUJITSU MPE3170AT ED-03-08

Primary Slave : None

Secondary Master : CREATIVEDVD-RM DVD1242E BC101

Secondary Slave : None

Press DEL to enter SETUP / Q-Flash

03/18/2003-I845GE-6A69YG01C-00

6. Press Del to enter BIOS menu after system reboots and "Load BIOS Fail-Safe Defaults". See how

to Load BIOS Fail-Safe Defaults, please kindly refer to Step 6 to 7 in Part One.

Congratulation!! You have updated BIOS successfully!!

Appendix- 57 -

STEP 3 :

Connect the front channels to back audio panel's

"Line Out", the rear channels to SURROUND-KIT's

REAR R/L, and the Center/Subwoofer channels to

English

SURROUND-KIT's SUB CENTER.

STEP 4 :

Click the audio icon "Sound Effect" from the win-

dows tray at the bottom of the screen.

STEP 5 :

Select "Speaker Configuration", and choose the

"6 channels for 5.1 speakers out put".

Enable "Only SURROUND-KIT" and press "OK".

Basic & Advanced 6 Channel Analog Audio Output Mode Notes:

When the "Environment settings" is "None", the

sound would be performed as stereo mode (2 chan-

nels output). Please select the other settings for 6

channels output.

GA-8I845GVM775 Motherboard - 64 -

SPDIF Output Device (Optional Device)

English

A "S/PDIF output" connector is available on the

motherboard. Cable with rear bracket is provided

and could link to the "S/PDIF output" connector (As

picture.) For the further linkage to decoder, rear

bracket provides coaxial cable and Fiber connect-

ing port.

1. Connect the SPDIF output device to the rear

bracket of PC, and fix it with screw.

2. Connect SPDIF wire to the motherboard.

3. Connect co-axial or optical output to the AC3

decoder.

Appendix- 65 -

4-1-5 Jack-Sensing Introduction

Jack-Sensing provides audio connectors error-detection

English

function.

Install Microsoft DirectX8.1 before to enable Jack-Sensing support for Windows 98/98SE/

2000/ME.

Jack-Sensing includes 2 parts: AUTO and MANUAL. Following is an example for 2 channels

(Windows XP):

Introduction of audio connectors

You may connect CDROM, Walkman or others

audio input devices to Line In jack, speakers,

earphone or others output devices to Line Out jack,

and microphone to MIC In jack.

Auto-detecting:

Please connect the devices to the right jacks as

above. A window will appear as right picture if

you setup the devices properly.

Please note that 3D audio function will only appear

when 3D audio inputs.

GA-8I845GVM775 Motherboard - 66 -

If you set wrong with the connectors, the warning

English

message will come out as right picture.

Manual setting:

If the device picture shows different from what you

set, please press "Manual Selection" to set.

Appendix- 67 -

4-2 Troubleshooting

Below is a collection of general asked questions. To check general asked questions based on a specific

motherboard model, please log on to http://tw.giga-byte.com/faq/faq.htm

English

Question 1: I cannot see some options that were included in previous BIOS after updating BIOS. Why?

Answer: Some advanced options are hidden in new BIOS version. Please press Ctrl and F1 keys after

entering BIOS menu and you will be able to see these options.

Questions 2: Why is the light of my keyboard/optical mouse still on after computer shuts down?

Answer: In some boards, a small amount of electricity is kept on standby after computer shuts down and

that's why the light is still on.

Question 3: How do I clear CMOS?

Answer: If your board has a Clear CMOS jumper, please refer to the Clear CMOS steps in the manual. If your

board doesn't have such jumper, you can take off the on-board battery to leak voltage to clear CMOS.

Please refer to the steps below:

Steps:

1. Turn off power.

2. Disconnect the power cord from MB.

3. Take out the battery gently and put it aside for about 10 minutes (Or you can use a metal object to

connect the positive and negative pins in the battery holder to makethem short for one minute).

4. Re-insert the battery to the battery holder.

5. Connect power cord to MB again and turn on power.

6. Press Del to enter BIOS and load Fail-Safe Defaults.

7. Save changes and reboot the system.

Question 4: Why does system seem unstable after updating BIOS?

Answer: Please remember to load Fail-Safe Defaults (Or Load BIOS Defaults) after flashing BIOS. However,

if the system instability still remains, please clear CMOS to solve the problem.

Question 5: Why do I still get a weak sound after turning up the speaker to the maximum volume?

Answer: Please make sure the speaker you are using is equipped with an internal amplifier. If not, please

change another speaker with power/amplifier and try again later.

Question 6: How do I disable onboard VGA card in order to add an external VGA card?

Answer: Gigabyte motherboards will auto-detect the external VGA card after it is plugged in, so you don't

need to change any setting manually to disable the onboard VGA.

GA-8I845GVM775 Motherboard - 68 -

Question 7: Why cannot I use the IDE 2?

English

Answer: Please refer to the user manual and check whether you have connected any cable that is not

provided with the motherboard package to the USB Over Current pin in the Front USB Panel. If the cable is

your own cable, please remove it from this pin and do not connect any of your own cables to it.

Question 8: Sometimes I hear different continuous beeps from computer after system boots up. What do

these beeps usually stand for?

Answer: The beep codes below may help you identify the possible computer problems. However, they are

only for reference purposes. The situations might differ from case to case.

AMI BIOS Beep Codes

 AWARD BIOS Beep Codes

*

Computer gives 1 short beep when system boots successfully.

1 short: System boots successfully

*Except for beep code 8, these codes are always fatal.

2 short: CMOS setting error

1 beep Refresh failure

1 long 1 short: DRAM or M/B error

2 beeps Parity error

1 long 2 short: Monitor or display card error

3 beeps Base 64K memory failure

1 long 3 short: Keyboard error

4 beeps Timer not operational

1 long 9 short: BIOS ROM error

5 beeps Processor error

Continuous long beeps: DRAM error

6 beeps 8042 - gate A20 failure

7 beeps Processor exception interrupt error

Continuous short beeps: Power error

8 beeps Display memory read/write failure

9 beeps ROM checksum error

10 beeps CMOS shutdown register read/write error

11 beeps Cache memory bad

Appendix- 69 -

English

GA-8I845GVM775 Motherboard - 70 -

English

Contact Us

 

 

 Taiwan (Headquarters)

 

 Japan

 

GIGA-BYTE TECHNOLOGY CO., LTD.

NIPPON GIGA-BYTE CORPORATION

Address: No.6, Bau Chiang Road, Hsin-Tien, Taipei Hsien,

WEB address : http://www.gigabyte.co.jp

Taiwan

 

 

 Singapore

TEL: +886 (2) 8912-4888

GIGA-BYTE SINGAPORE PTE. LTD.

FAX: +886 (2) 8912-4003

Tech. Support :

Tech. Support :

http://tw.giga-byte.com/TechSupport/ServiceCenter.htm

http://tw.giga-byte.com/TechSupport/ServiceCenter.htm

Non-Tech. Support(Sales/Marketing) :

Non-Tech. Support(Sales/Marketing) :

http://ggts.gigabyte.com.tw/nontech.asp

http://ggts.gigabyte.com.tw/nontech.asp

 U.K.

 

 

WEB address (English): http://www.gigabyte.com.tw

G.B.T. TECH. CO., LTD.

WEB address (Chinese): http://chinese.giga-byte.com

Address: GUnit 13 Avant Business Centre 3 Third Avenue,

 U.S.A.

 

 

Denbigh West Bletchley Milton Keynes, MK1 1DR, UK, England

G.B.T. INC.

TEL: +44-1908-362700

Address: 17358 Railroad St, City of Industry, CA 91748.

FAX: +44-1908-362709

TEL: +1 (626) 854-9338

Tech. Support :

FAX: +1 (626) 854-9339

http://uk.giga-byte.com/TechSupport/ServiceCenter.htm

Tech. Support :

Non-Tech. Support(Sales/Marketing) :

http://www.giga-byte.com/TechSupport/ServiceCenter.htm

http://ggts.gigabyte.com.tw/nontech.asp

Non-Tech. Support(Sales/Marketing) :

WEB address : http://uk.giga-byte.com

http://ggts.gigabyte.com.tw/nontech.asp

 

 

 The Netherlands

WEB address : http://www.giga-byte.com

GIGA-BYTE TECHNOLOGY B.V.

 

 Germany

 

TEL: +31 40 290 2088

G.B.T. TECHNOLOGY TRADING GMBH

NL Tech.Support: 0900-GIGABYTE (0900-44422983)

Address: Friedrich-Ebert-Damm 112 22047 Hamburg

BE Tech.Support: 0900-84034

TEL: +49-40-2533040 (Sales)

FAX: +31 40 290 2089

+49-1803-428468 (Tech.)

Tech. Support :

FAX: +49-40-25492343 (Sales)

http://nz.giga-byte.com/TechSupport/ServiceCenter.htm

+49-1803-428329 (Tech.)

Non-Tech. Support(Sales/Marketing) :

Tech. Support :

http://ggts.gigabyte.com.tw/nontech.asp

http://de.giga-byte.com/TechSupport/ServiceCenter.htm

WEB address : http://www.giga-byte.nl

Non-Tech. Support(Sales/Marketing) :

http://ggts.gigabyte.com.tw/nontech.asp

WEB address : http://www.gigabyte.de

Appendix- 71 -

 

 

 China

 Australia

 

 

NINGBO G.B.T. TECH. TRADING CO., LTD.

GIGABYTE TECHNOLOGY PTY. LTD.

Tech. Support :

Tech. Support :

http://cn.giga-byte.com/TechSupport/ServiceCenter.htm

http://www.giga-byte.com.au/TechSupport/ServiceCenter.htm

English

Non-Tech. Support(Sales/Marketing) :

Non-Tech. Support(Sales/Marketing) :

http://ggts.gigabyte.com.tw/nontech.asp

http://ggts.gigabyte.com.tw/nontech.asp

WEB address : http://www.gigabyte.com.cn

WEB address : http://www.giga-byte.com.au

Shanghai

 

 France

 

TEL: +86-021-63410999

GIGABYTE TECHNOLOGY FRANCES S.A.R.L.

FAX: +86-021-63410100

Tech. Support :

Beijing

http://tw.giga-byte.com/TechSupport/ServiceCenter.htm

TEL: +86-010-82886651

Non-Tech. Support(Sales/Marketing) :

FAX: +86-010-82888013

http://ggts.gigabyte.com.tw/nontech.asp

Wuhan

WEB address : http://www.gigabyte.fr

TEL: +86-027-87851061

 Russia

 

 

FAX: +86-027-87851330

Moscow Representative Office Of Giga-Byte Technology Co.,

GuangZhou

Ltd.

TEL: +86-020-87586074

Tech. Support :

FAX: +86-020-85517843

http://tw.giga-byte.com/TechSupport/ServiceCenter.htm

Chengdu

Non-Tech. Support(Sales/Marketing) :

TEL: +86-028-85236930

http://ggts.gigabyte.com.tw/nontech.asp

FAX: +86-028-85256822

WEB address : http://www.gigabyte.ru

Xian

 Poland

 

 

TEL: +86-029-85531943

Representative Office Of Giga-Byte Technology Co., Ltd.

FAX: +86-029-85539821

POLAND

Shenyang

Tech. Support :

TEL: +86-024-23960918

http://tw.giga-byte.com/TechSupport/ServiceCenter.htm

FAX: +86-024-23960918-809

Non-Tech. Support(Sales/Marketing) :

http://ggts.gigabyte.com.tw/nontech.asp

WEB address : http://www.gigabyte.pl

GA-8I845GVM775 Motherboard - 72 -