Beko WKE 13580 D: Things to do Before Calling the Authorized Service
Things to do Before Calling the Authorized Service: Beko WKE 13580 D
EN
Things to do Before Calling the Authorized Service
If the light of the 1st auxiliary function
It is in the child-lock mode. (See. Child-lock)
on the left hand side is flashing
The program selection knob may be in-between
If the cover and washing light on the
position.
program follow-up indicator is
Readjust the program by turning the program
flashing and the end light is
selection knob. If the warning continues, contact
constantly on
the authorized service.
If the light of Start/Pause/Cancel
The door is unlocked. Open and close the door
button starts to flashing after a short
again and restart the washing program.
time you start your machine
The water may be cut or the taps may be closed.
If the “Washing” light on the program
Check the taps. Turn off your machine and restart.
follow-up indicator is flashing
If the fault persists, unplug your machine, close the
taps and contact the authorized service.
Machine may be in the self-protection mode due to the
substructure problems (grid voltage, water pressure
and etc.)
If the program can not be started or
Therefore, you can not start or select a program. Press
selected
Start/Pause/Cancel button for 3 seconds and return
the machine to the factory settings. (See.Cancelling a
Program)
If the water is cut while your machine
is operating, the current program
Press “Start/Pause/Cancel” button, program will
does not proceed. To continue the
proceed.
program
Your machine may stop due to the
Wait for a while. When the voltage reaches to a
low voltage
normal level your machine will start to operate.
During the production, some water
may have remained in your machine
This does not cause any damage to your machine.
because of the quality control
processes.
You have selected the program
The plug of your machine may not be plugged in a
in your machine and pressed the
grounded outlet, front cover may not be closed or
“Start/Pause/Cancel” button but the
the fuse may be blown.
machine did not start
Check the water inlet and drainage hoses. Are they
Is water coming from under your
well mounted? Gaskets of the water inlet hoses
machine
may not be well seated. If the problem is none of
them, the pump filter may not be well closed.
Check if the drainage hose is connected as
Is the water drained directly?
described in the user guide.
During the water drainage, you may
This sound is normal.
hear water sound from the pump
Check if your detergent is suitable for automatic
Is foam running over the detergent
machine. Use the recommended amount of
drawer?
detergent in your next washing.
If sometimes you are not satisfied
Make sure that you have selected the correct
with the rinsing and spinning
program, you have adjusted the speed adjusting/
efficiency (laundries have
decrease button correctly and you have loaded the
detergent remnants or they are not
right laundries for the program you have chosen, try
dry enough)?
again when the voltage is normal.
23
Оглавление
- Содержание
- Ваша стиральная машина
- Спецификация Вашей стиральной машины
- Предостережения
- Установка 1. Удаление упаковочных креплений
- Соединения для воды
- Подключение к электросети
- Выбор программы и эксплуатация Вашей машины Панель управления
- Табличка выбора программы
- Выбор функции
- Изменение программы
- Разгрузка машины
- Чистка фильтра насоса
- Contents
- Your Washing Machine
- Models
- Warnings
- Things to do Before Calling the Authorized Service
- Installation 1. Removing the packaging reinforcements
- Water connections
- Electrical Connection
- Program Selection and Operating Your Machine Control Panel
- Program selection table
- Function Selection
- Changing the Program
- Unloading the Laundries
- Hose