Siemens EH845BC17E: Important notes Preparation of assembly kitchen units, figures 1/2/3/4 Installing the appliance, figures 5/6/7 Uninstalling the appliance

3.

Gerät an das Netz anschließen und Funktion prüfen.

– Spannung siehe Typenschild.

– Nur gemäß Anschlussbild anschließen 

(Abbildung 7)

.

1. Braun

2. Schwarz

3. Blau

4. Grau

5. Grün-gelb

Hinweis: 

Je nach Anschlussart muss eventuell die Anordnung 

der vom Werk gelieferten Klemmen verändert werden.

Ausbau des Geräts

Das Gerät vom Stromnetz trennen. 

Von unten gegen das Kochfeld drücken und das Kochfeld her-

ausnehmen. 

Achtung!

Schäden am Gerät! Versuchen Sie nicht, das Gerät durch 

Hebeln von oben zu entnehmen.

en

Ú

 Installation instructions

Important notes

Safety:

 Safety in use is only guaranteed if the technical 

installation of the hob has been carried out correctly and in 

accordance with the assembly instructions. The installation 

technician shall be liable for any damage caused as a result of 

unsuitable installation.

Electric connection:

 Only by an authorised specialist 

technician. The guidelines set out by the local electricity provider 

must be observed.

Type of connection:

 The appliance falls under protection class I 

and can only be used in combination with a grounding 

conductor connection.

The manufacturer accepts no responsibility for any malfunction 

or damage caused by incorrect electrical installations.

Installation:

 The appliance must be connected to a fixed 

installation and the means of disconnecting it from the fixed 

installation must be installed according to the installation 

instructions.

Built-in assembly under worktop:

 The induction hobs may only 

be installed over a drawer, ovens with forced ventilation from the 

same brand and dishwashers from the same brand. 

Refrigerators, unventilated ovens and washing machines may 

not be installed beneath the hob.

Power cable: 

Do not tie the power cable or pass it along sharp 

edges. If there is an oven installed below, pass the cable along 

the rear corners of the oven to the connection box. It must be 

positioned so that it does not touch any of the hot parts of the 

hob or the oven.

Hob:

 flat, horizontal, stable. Follow the hob manufacturer's 

instructions.

Warranty:

 an unsuitable installation, connection or assembly will 

invalidate the product warranty.

Note: 

Any change to the appliance's interior, including changing 

the power cable, must only be performed by specially trained 

members of the Technical Assistance Service.

Preparation of assembly kitchen units, 

figures 1/2/3/4

Built-in kitchen units:

 Minimum temperature resistance of 

90°C.

Gap:

 Remove any shavings after performing cutting work.

Cut surfaces:

 Seal with heat resistant material.

Assembly over drawer, figure 2a

Metal objects stored inside the drawer could become very hot 

due to the air recirculating from the hob ventilation system. If 

this occurs, an intermediate support is recommended.

Intermediate support: A wooden panel can be used 

(figure 3)

 or 

you may order a suitable accessory from our Technical 

Assistance Service. The reference code for this accessory 

is 680502.

Worktop: Must have a minimum thickness of 20 mm.

The distance between the top of the working surface and the top 

of the drawer must be 65 mm.

Assembly over oven, figure 2b

Hob: must have a minimum thickness of 30 mm.

Note: 

If the distance between the hob and oven must be 

increased, refer to the installation instructions for the oven.

Ventilation: The distance between the oven and the hob must be 

at least 5 mm.

Installation above the dishwasher

An intermediate accessory must be installed. The accessory 

may be ordered from our Technical Assistance Service. The 

reference code for this accessory is 680502.

Worktop: Must have a minimum thickness of 20 mm and 

maximum thickness of 40 mm.

The space between the top of the working surface and the top 

of the dishwasher must be:

■

60 mm if installed over a compact dishwasher.

■

65 mm if installed over a full-size dishwasher.

Ventilation, figure 4

Ventilating the hob requires:

■

An opening on the upper part of the kitchen unit's rear wall 

(figure 4a)

.

■

A separation between the rear part of the kitchen unit and the 

kitchen wall 

(figure 4b)

.

■

If the interior width of the kitchen unit is less than 780 mm, a 

cut must be made in the side walls 

(figure 4c)

.

Installing the appliance, figures 5/6/7

Note: 

Wear protective gloves to fit the hob. The non-visible 

surfaces may have sharp edges.

1.

 Installation of fastening guides, 

(figure 5)

:

– use the lower threaded holes on tiled worktops.

– For stone worktops, glue the guides (use thermosetting 

adhesive tape suitable for joining metal and stone).

2.

Check that the hob is flush with the worktop. If the hob is not 

flush, install the anchoring devices supplied and tighten them 

carefully, 

(figure 6)

.

Note: 

Do not use electric screwdrivers.

3.

Connect the appliance to the mains and check that it works 

correctly.

– See the rating plate for the voltage.

– Only connect the appliance in accordance with the 

connection diagram 

(Fig. 7)

.

1. Brown

2. Black

3. Blue

4. Grey

5. Green-yellow

Note: 

Depending on the type of connection, the arrangement of 

the clamps supplied by the factory may need to be changed.

Uninstalling the appliance

Disconnect the appliance from the mains. 

Push the hob upwards from below to remove it.

Caution!

Damage to the appliance! Do not try to remove the appliance by 

prying it out from above.

fr

Þ

 Notice de montage

Remarques importantes

Sécurité :

 la sécurité pendant l'utilisation n'est garantie que si 

l'installation a été effectuée de manière correcte du point de vue 

technique et conformément à ces instructions de montage. 

L'installateur sera responsable de tout dommage provoqué par 

un montage incorrect.

Connexion électrique :

 ne peut être effectuée que par un 

spécialiste autorisé. Il devra suivre les dispositions du 

fournisseur d'électricité dans la zone.

Type de branchement :

 l'appareil fait partie de la classe de 

protection I et ne peut être utilisé qu'avec une prise possédant 

un conducteur de prise de terre.

Le fabricant se dégage de toute responsabilité quant au 

fonctionnement inapproprié et aux possibles dommages 

provoqués par des installations électriques non appropriées.

Installation :

 l'appareil doit être connecté à une installation fixe 

et des moyens de déconnexion doivent être prévus sur 

l'installation fixe, conformément aux réglementations de 

l'installation.