Siemens EH601FV17E: Important notes Preparation of assembly kitchen units, figures 1/2/3/4 Installing the appliance, figures 5/6 Uninstalling the appliance

4.

Vor dem Abdichten (Abb. 5) unbedingt einen Betriebstest 

durchführen! 

Den Abstand zwischen den Bereichen mit geeignetem hitzebe-

ständigen Silikon (z. B.  Novasil

®

S70, Ottoseal

®

S70) abdichten. 

Die hermetische Dichtung mit einem vom Hersteller empfohle-

nen Produkt glätten. Die Angaben auf dem Silikon beachten. 

Das Gerät nicht in Betrieb nehmen, bevor das Silikon vollstän-

dig getrocknet ist (je nach Umgebungstemperatur, mindestens 

24 Stunden).

Geeignetes Silikon kann bei unserem Kundendienst erworben 

werden.

Achtung!

Wird bei Arbeitsplatten aus Naturmarmor ungeeignetes Silikon 

verwendet, können Verfärbungen entstehen, die nicht entfernt 

werden können.

Ausbau des Geräts

Das Gerät von der Stromzufuhr trennen. 

Die Silikondichtung der gesamten Umrandung des Kochfelds 

mit einem geeigneten Werkzeug entfernen. 

Kochfeld von unten herausdrücken.

Achtung!

Schäden am Gerät! Versuchen Sie nicht, das Gerät durch 

Hebeln von oben zu entnehmen.

en

Ú

 Installation instructions

Important notes

Safety:

 Safety in use is only guaranteed if the technical 

installation of the hob has been carried out correctly and in 

accordance with the assembly instructions. The installation 

technician shall be liable for any damage caused as a result of 

unsuitable installation.

Electric connection:

 Only by an authorised specialist 

technician. The guidelines set out by the local electricity provider 

must be observed.

Type of connection:

 The appliance falls under protection class I 

and can only be used in combination with a grounding 

conductor connection.

The manufacturer accepts no responsibility for any malfunction 

or damage caused by incorrect electrical installations.

Installation:

 The appliance must be connected to a fixed 

installation and the means of disconnecting it from the fixed 

installation must be installed according to the installation 

instructions.

Built-in assembly under worktop:

 The induction hobs may only 

be installed over a drawer, ovens with forced ventilation from the 

same brand and dishwashers from the same brand. 

Refrigerators, unventilated ovens and washing machines may 

not be installed beneath the hob.

Power cable: 

Do not tie the power cable or pass it along sharp 

edges. If there is an oven installed below, pass the cable along 

the rear corners of the oven to the connection box. It must be 

positioned so that it does not touch any of the hot parts of the 

hob or the oven.

Hob:

 flat, horizontal, stable. Follow the hob manufacturer's 

instructions.

Warranty:

 an unsuitable installation, connection or assembly will 

invalidate the product warranty.

Note: 

Any change to the appliance's interior, including changing 

the power cable, must only be performed by specially trained 

members of the Technical Assistance Service.

Preparation of assembly kitchen units, 

figures 1/2/3/4

Built-in kitchen units:

 Minimum temperature resistance of 

90°C.

Gap:

 Remove any shavings after performing cutting work.

Cut surfaces:

 Seal with heat resistant material.

The appliance can be mounted on the following heat and water 

resistant worktops:

■

Marble, natural stone worktops

■

Synthetic worktops

■

Solid wood worktops: only according to the manufacturer of 

the worktop (sealing of cutout edges)

■

Assembly with other types of worktops: only according to the 

manufacturer of the worktop

Note: 

All worktop cutout work must be carried out by a 

specialised service according to the assembly drawings. The 

cutout must be clean and precise, as the cut edge will be visible 

on the surface. Clean and degrease the cutout edges using a 

suitable cleaning product (check the silicone manufacturer's 

indications).

Assembly over drawer, figure 2a

Metal objects stored inside the drawer could become very hot 

due to the air recirculating from the hob ventilation system. If 

this occurs, an intermediate support is recommended.

Intermediate support: A wooden panel can be used 

(figure 3)

 or 

you may order a suitable accessory from our Technical 

Assistance Service. The reference code for this accessory 

is 680502.

Hob: must have a minimum thickness of 30 mm.

The distance between the top of the hob and the top of the 

drawer must be 70 mm.

Assembly over oven, figure 2b

Hob: must have a minimum thickness of 30 mm.

Note: 

If the distance between the hob and oven must be 

increased, refer to the installation instructions for the oven.

Ventilation: The distance between the oven and the hob must be 

at least 5 mm.

Installation above the dishwasher

An intermediate accessory must be installed. The accessory 

may be ordered from our Technical Assistance Service. The 

reference code for this accessory is 680502.

Hob: must have a minimum thickness of 30 mm and a 

maximum thickness of 40 mm.

The space between the top of the hob and the top of the 

dishwasher must be:

■

65 mm if installed over a compact dishwasher.

■

70 mm if installed over a full-size dishwasher.

Ventilation, figure 4

Ventilating the hob requires:

■

An opening on the upper part of the kitchen unit's rear wall 

(figure 4a)

.

■

A separation between the rear part of the kitchen unit and 

kitchen wall 

(figure 4b)

.

Installing the appliance, figures 5/6

Note: 

Wear protective gloves to fit the hob. The non-visible 

surfaces may have sharp edges.

1.

Insert the appliance uniformly in the cutout. 

2.

Check that the hob is flush with the worktop.

3.

Connect the appliance to the mains and check that it works 

correctly.

– See the rating plate for the voltage.

– Only connect the appliance in accordance with the 

connection diagram 

(Fig. 6)

.

1. Brown

2. Black

3. Blue

4. Grey

5. Green-yellow

Note: 

Depending on the type of connection, the arrangement of 

the clamps supplied by the factory may need to be changed.

4.

Before sealing the joint (figure 5) you must test that the 

appliance works! 

Grout the perimeter separation using appropriate, heat 

resistant silicone ( e.g. Novasil

®

 S70, Ottoseal

®

 S70). Smooth 

the seal with a finishing product recommended by the 

manufacturer. Follow the silicone indications. Do not start the 

appliance until the silicone is completely dry (minimum 

24 hours, depending on the ambient temperature).

The appropriate silicones can be obtained through our 

Technical Assistance Service.

Caution!

The use of unsuitable silicone causes permanent colour 

changes to natural marble worktops.

Uninstalling the appliance

Disconnect the appliance from the mains. 

Remove the silicone seal from the edge of the hob with a 

suitable tool. 

Push the hob upwards from below to remove it.