Alexika ROCKER 2D basic: Unpacking

12

Unpacking

• 

Unpacking

- Please unpack the device carefully.

- In the case of any damage a detailed report must be sent immediately (post, rail or forwarder).

• Delivery scope

IKA

®

 Rocker 2D basic/ digital

- 

IKA

®

 Rocker 2D basic/digital, 

depending on the type that was ordered

- Mat 

- AC adapter, see Fig. 1 

- Operating instructions

- Warranty card

Fig. 1

Safety instructions

• The appliance is not suitable for manual operation.

• Beware of the risk of

- flammable materials

- glass breakage as a result of mechanical shaking power

• The appliance may heat up when in use.

• Only process media that will not react dangerously to the ex-

tra energy produced through processing. This also applies to 

any extra energy produced in other ways, e.g. through light 

irradiation.

•  Process  pathogenic  materials  only  in  closed  vessels  under  a 

suitable extractor hood. Please contact 

IKA

®

 if you have any 

questions.

• Do 

not

 operate the appliance in explosive atmospheres, with 

hazardous substances or under water.

• 

Safe operation is only guaranteed with the accessories descri-

bed in the ”Accessories” chapter.

• Always disconnect the plug before fi tting accessories.

• Disconnect the device from the power supply before you open 

the cover or adjust the inclination angle of the device shaking 

table.

• Do not operate the device with the cover open.

• The appliance can only be disconnected from the mains supply 

by pulling out the mains plug or the connector plug.

•  The socket for the mains cord must be easily accessible.

•  The 

IKA

®

Rocker 2D basic

 does not restart automatically 

when power is restored after a power outage. If the 

IKA

®

Rocker 2D digital

 is running in mode A it does not restart 

automatically when power is restored after a power outage.

For protection of the equipment

• The appliance may only be opened by experts.

• The voltage stated on the type plate must correspond to the 

mains voltage.

• Removable parts must be refitted to the appliance to prevent 

the infiltration of foreign objects, liquids etc..

• Protect the appliance and accessories from bumps and impacts.

•  The  device  must  only  be  operated  with  the  original  plug-in 

power supply unit.

For your protection

•  

Read the operating instructions in full be-

fore starting up and follow the safety in-

structions.

• Keep the operating instructions in a place where

                       they can be accessed by everyone.

• Ensure that only trained staff work with the appliance.

• Follow the safety instructions, guidelines, occupational health 

and safety and accident prevention regulations.

• Wear your personal protective equipment in accordance with 

the hazard category of the medium to be processed. Otherwise 

there is a risk of:

- splashing liquids

- projectile parts

- body parts, hair, clothing and jewellery getting caught.

• 

Set up the device in a spacious area on an even, stable, clean, 

non-slip, dry and fireproof surface.

• The feet of the appliance must be clean and undamaged.

• Check the appliance and accessories beforehand for damage 

each time you use them. Do not use damaged components.

• 

Caution! 

There is a crush hazard between the 

moving shaking table and the casing.

• Place the vessels securely on the shaking table or on the cho-

sen mat or rack.

• Firmly secure the accessories and vessels in place, otherwise 

shaking vessels could be damaged or projected out.

• Position one single shaking vessel in the centre and several 

   shaking vessels so that they are evenly spread out.

• Always load the samples evenly on the device.

• The weight of the load must not exceed 2 kg. Do not exceed 

the maximum permissible shaking weights.

• Do not move or transport the device when it is operating or 

connected to the power supply.

• Reduce the speed if

- the medium splashes out of the vessel because the speed is

     too high

- the appliance is not running smoothly

- dynamic forces start to cause the device and/or the vessels 

      placed on it to move around.