Intimus 100 CP7: GB

IMPORTANT SAFETY NOTES

<< The machine may not be operated by more

<< Danger of injury! Keep all

SCOPE OF APPLICATION:

than one person at any given time!

loose articles of clothing, ties,

The document shredder intimus 100SP2/CP4/

The machine was designed for safe operation

jewelery, long hair or other loose

CP5/CP6/CP7 is a machine for the destruction

by “one person only”.

objects away from opening!

of common written material.

The machine may only be used to

<< Danger of injury! Never insert ngers into

shred paper!

<< During the shredding process no other

opening!

Shredding of other types of data carriers

work may be performed on the machine

and also of staples and paper clips with

(for example cleaning, etc.)!

the models with cutting width 0.8x12 mm

<< In case of danger switch the machine off

(CP6) or 0.8x4.5 mm (CP7) may lead to

with the mains switch, or with the emer-

injuries (for example due to splintering of

<< The machine is not a toy, and is not suitable

gency switch, or unplug the machine!

hard materials etc.) and damage to the

for use by children!

machine (for example destruction of the

The overall technical safety concept of

<< Always unplug the machine from the

cutter etc.).

this machine (dimensions, feed openings,

mains power supply before opening the

emergency shutdown devices etc.) does not

machine!

INSTALLATION:

provide for any guarantee regarding hazard-

Repairs may only be performed by trained

- Unpack and set machine upright.

free operation by children.

personnel!

- Place plastic sack into the receptacle.

- Plug in the machine (for instructions for the

necessary precautions see „TECHNICAL

DATA“.

The air vents in the housing are ne-

cessary for cooling and may not be

covered or closed!

CONTROLS:

4 = Pilotlamp(g.1)

The mains connection at the machine

1 = Pushbuttonswitch(g.1)

„ready“

must be freely accessible!

“Ready”/ “Off”

Lights when the pushbutton switch (1) is

Only operate the machine in enclosed

This button has two functions:

operated.

rooms at temperatures between 10°C

a) “Ready”

5 = Pilotlamp(g.1)

and 25°C!

The machine changes to “Ready” if you

„receptacle full“ / „door open“

press this button briey.

a) Flashes when the receptacle is full and

b) “Off”

needs to be emptied. At the same time

The machine switches off if it is in the

the machine switches off automatically.

“Ready” mode and the button is held

b) Lights when the door is not closed. The

down for about 3 seconds.

machine then switches off automatically

Note: The machine switches off

and it cannot be started as long as the

Note: In order to always obtain a correct cutting

automatically if it is not used for about 5

door is open.

result in terms of particle size and thus achieve

minutes.

6 = Pilotlamp(g.1)

the safety class according to DIN 66399 as

2 = Lightbarrier(forwardoperation)(g.2)

„Paper jam“ / „Stop“

stated in the brochure, the material to be cut

The shredding operation is started as soon

Lights up, if

must always be fed into the cutting mechanism

as a sheet of paper passes through the feed

a) too much paper has been fed into the

at a right angle to the cutting mechanism and in

slot.

cutting mechanism. The shredding

appropriate quantities in the middle of the inlet

3 = Pushbuttonswitch(g.1)

mechanism jams and stops. The motor is

slot.

„Backward operation“ / „Stop“

switched off.

This button has two functions:

b) while the cutting mechanism is running,

Never feed the shredder with a quantity

a) “Backward operation”

the pushbutton switch (3) is pressed. The

of paper exceeding the maximum indi-

If this switch is pressed, the shredding

cutting mechanism is switched off and

cated in the technical details!

mechanism runs in reverse.

stops.

Should the machine be overfed, follow the

b) “Stop”

instructions under „PAPER JAM“.

If you briey press this button while

FEEDING OF SHEETS:

the cutting mechanism is running, it is

- Turn machine on with pushbutton switch (1)

switched off and stops.

(g. 1). Pilot lamp lights up (4) (g. 1).

Note: If pressed again when the

- Feed paper through the inlet guide to the cutting

light barrier is activated, the cutting

system.

mechanism will run forwards again and

- Machine switches automatically to forward

continues with the shredding process.

and draws paper in. The machine switches off

automatically after shredding.

Translation of the Original Operation Manual

GB

Übersetzung der Originalbetriebsanleitung

INITIATION

OPERATION

OPERATION

g. 1 g. 2

g. 3

4

Translation of the Original Operation Manual

GB

Übersetzung der Originalbetriebsanleitung

OPERATION

MAINTENANCE

EMPTYINGTHECOLLECTINGBAG(g.3):

MAINTENANCE CUTTING BLOCK:

Once the collecting bag is full, the machine

(cross-cut)

switches off. The pilot lamp „Container full“ /

After approximately 15 minutes of con-

„Door open“ (5) (g. 1) ashes. To show that the

tinuous use, run the cutting system in

cutting mechanism has stopped, the pilot lamp

reverse for 15 to 20 seconds and spray

“Paper jam” / “Stop” (6) lights up.

some of the enclosed Special Oil onto the

Empty the collecting bag as follows:

cutting system.

- Open the door and take out the sliding frame

with the collecting bag.

AUTOMATIC ENERGY SAVING:

- Remove the rubber band, take out the full bag

If the machine is not used for a while it

and dispose of contents.

automatically switches off after about 5 minutes.

- Put the empty bag from below through the sliding

The pilot lamp (4) for “Ready” goes off. Press the

frame and put the edges of the bag approx. 10

pushbutton switch (1) briey to turn it on again.

cm over the frame outwardly.

- Move back the sliding frame with the collecting

CLEANINGTHEPHOTOCELLS(g.4):

g. 4

bag and close door. The pilot lamp (5) (g. 1)

If paper particles should come to rest in the inlet

goes off.

guide (for example after a paper jam) it is possi-

- Briey press the pushbutton switch „Backward

ble that the machine will not turn off, due to the

operation“ / „Stop“ (3). The cutting mechanism

broken light barrier.

shreds what remains in the feed shaft and then

To remove these paper strips and also to clean

switches off. The pilot lamp (6) goes out. You

the photocell, pass another sheet of paper through

can now continue shredding.

the feed slot, or switch the machine to reverse and

Note: The machine will only run with closed

wipe both „eyes“ of the photocell with a brush.

door!

TECHNICAL DATAMALFUNCTIONS

PAPER JAM:

MOTOR PROTECTION:

Cutting width:

If too much paper is fed to the cutting system the

The motor shuts down automatically, should it

100SP2: 5.8 mm (strips)

machine will react as follows:

become overloaded. Turn the machine off with

100CP4: 3.8x36 mm (cross-cut)

- The cutting system blocks, reverses a bit to

the pushbutton switch (1) (g. 1).

100CP5: 1.9x15 mm (cross-cut)

release the paper and then stops.

Allow the motor to cool down for 15 to 20 minutes

100CP6: 0.8x12 mm (cross-cut)

- The motor shuts down automatically.

(depending upon room temperature) and then

100CP7: 0.8x4.5 mm (cross-cut)

- The pilot lamp (6) (g. 1) lights up.

continue shredding.

Cutting capacity:

100SP2: 23-25 sheets (70g/m

2

Proceed as follows:

)

- Continuously press pushbutton switch

100CP4: 18-20 sheets (70g/m

2

CHECKLIST IN CASE OF MALFUNCTIONS:

)

2

“Backward operation” / “Stop” (3) while

If the device does not function, check the fol-

100CP5: 13-15 sheets (70g/m

)

100CP6: 8-10 sheets (70g/m

2

simultaneously removing from the machine

lowing:

)

2

any documents that were being fed in.

- Is the plug connected to the mains?

100CP7: 5-6 sheets (70g/m

)

- After removal, the cutting mechanism

Mains connection: 2-pole mains switch,

Supply voltage: 230V/50Hz

automatically runs forwards, shreds any

internal appliance plug,

240V/50Hz

remnants remaining in the inlet slot and then

separate power cord

120V/60Hz

switches off. The pilot lamp (6) (g. 1) goes

- Is the pushbutton switch (1) on?

100V/50/60Hz

out.

- Is the door closed?

Pre-fusing:

Note: If removal is not possible, then briey

- Is the receptacle full?

230V/240V/50Hz: 10 amps (slow-blow)

press the pushbutton switch “Backward

The receptacle has to be emptied.

120V/100V/50/60Hz: 20 amps (slow-blow)

operation” / “Stop” (3) again. The cutting

- Is there a paper jam?

Workingwidth: 260 mm

mechanism now automatically repeats the

Follow the instructions under „paper jam“.

Noise level: approx. 54 dB(A)

process as described above until the paper

- has the motor been overloaded?

Power:

remaining in the cutting mechanism has run

Wait until the motor has cooled, and then re-

100SP2, 100CP4-CP6: 1.1 kW

through.

start.

100CP7: 1.5 kW

- Remove excess paper from the machine and

If none of the above applies, please contact

Dimensions (WxDxH): 490x430x870 mm

continue shredding with less paper.

your dealer.

Weight: ca. 43 kg

ACCESSORIES DISPOSING

Description Order-No.

DISPOSING OF THE MACHINE:

Plastic bag, 440 x 330 x 950 x 0,05 mm 99977

Dispose of the machine in an

environmentally sound fashion at the end

Lubricant, 110 ml bottle (cross-cut) 88035

of its useful service life. Do not dispose of

Note: For orders of special accessories and spare parts, please contact your dealer.

any of the parts included in the machine

or its packaging with household trash.

5