Beko WMD 25080 R: Installation
Installation: Beko WMD 25080 R
Installation
6
If your system is not ready, let a certified plumber make it
2. Leveling the feet
ready.
In order to operate your machine without noise and vibra-
tion it must be properly on balance. Four feet of your ma-
1. Removing the transportation safety bolts
chine can be adjusted. First loosen the plastic counter bolt.
Tighten the counter bolt after adjusting the feet for leveling
Before the washing machine is operated, the transit bars
your machine.
must be removed! In order to do this:
1. Loosen “C” bolts by rotating them counter clockwise
with a suitable spanner
3. Water Connections
2. Remove transportation safety bolts by turning.
3. Place “P” plastic covers onto the openings of transpor-
a) Water Inlet Hose
tation locks by rotating in direction of arrow and pushing.
Your machine is connected to water supply by special
hoses supplied by the machine. Red hose or hose
Attention please! Keep the transit bars for using when
written red on it is hot water inlet, blue hose or hose
machine is to be transported again. Always transport your
written blue on it is cold water inlet.
machine with transportation locks.
There are plastic seals (4 for double water inlet mod-
els, 2 for single water inlet models) on hose or plastic
bag for eliminating any leakage in connections points.
These seals must be used on each side of the connec-
20
tion. Seals on machine side must be connected lter
cannal.
Do not connect single inlet machine to hot water. If
machine is connected with Y part to a double inlet
After connecting the hose, check all connections for
and over 40˚C for single inlet machines, machine may
leaks In order to eliminate any risk due to water leakage
switch to protection mode.
keep the taps off when machine is not used.
b) Water drain hose
Water drain hose could be placed either at the side of the
bath tub, or directly to the drain. The hose should not be
bent. Water drain hose should be secured with the holder
so that it would not fall down on the ground.
The hose should be placed between 40 and 100 cm. from
the ground.
Your machine will operate efciently if the water from
Water drain hose could be placed directly to the drain
tap is minimum 1 and maximum 10 bars. Practically 1
water inlet.
bar means 8 liters of water in one minute when tap is
fully on.
Connect hose to the machine. Tighten bolts with hand
power, do not use spanner.
Double inlet models can be used with blind cap as a
single inlet machine. Connect blind cap to hot water
inlet. Seal must be for stopping water leakage.
21
4. Electrical connection
Connect the power cord to the appropirate electrical sys-
tem which is being supported by the maximum voltage and
current rating indicated on the rating plate placed inside the
kick plate.
Look! Page 1, Steps before operating Fullautomatic Wash-
ing Machine and safety precautions.
Make sure that you have grounded power outlet.
Attention! Before any operation of the machine check the
following.
• Did you close the front door?
• Is the tap open?
• Is water drain hose placed properly?
• Is power connected?
22
Оглавление
- Technical Features of Your Washing Machine
- Your Washing Machine
- Warning
- Preparation
- Control Panel
- Auxiliary Functions
- Program Selection and Starting Machine
- Care and maintanence
- Installation
- Helpful tips on stain removal
- Before calling service
- Содержание
- Технические особенности Вашей стиральной машины
- Ваша Стиральная машина
- Предостережения по безопасности работы с машиной
- Подготовка к стирке
- Пульт управления
- Вспомогательные Функции
- Выбор программы и запуск машины
- Таблица выбора программ
- Уход за машиной и техническое обслуживание
- Установка