Beko TS1 90320: 3 Installation
3 Installation: Beko TS1 90320
3 Installation
BPlease remember that the
manufacturer shall not be held liable if
the information given in the instruction
manual is not observed.
Points to be considered
when re-transporting your
refrigerator
1.Your refrigerator must be emptied and
cleaned prior to any transportation.
(The illustrated figure is only an
2.Shelves, accessories, crisper and etc.
example and does not match exactly
in your refrigerator must be fastened
with your product.)
securely by adhesive tape against any
jolt before repackaging.
3.Packaging must be tied with thick
3.Clean the interior of the refrigerator as
tapes and strong ropes and the
recommended in the “Maintenance
rules of transportation printed on the
and cleaning” section.
package must be followed.
4.Plug the refrigerator into the wall outlet.
Please do not forget…
When the fridge door is open, the
Every recycled material is an
fridge compartment interior light will
indispensable source for the nature
come on.
and for our national resources.
5.You will hear a noise as the compressor
If you wish to contribute to recycling
starts up. The liquid and gases sealed
the packaging materials, you can
within the refrigeration system may
get further information from the
also give rise to noise, even if the
environmental bodies or local
compressor is not running and this is
authorities.
quite normal.
6.Front edges of the refrigerator may feel
Before operating your
warm. This is normal. These areas
refrigerator
are designed to be warm to avoid
Before starting to use your refrigerator
condensation
check the following:
Electric connection
1.Is the interior of the refrigerator dry and
can the air circulate freely in the rear
Connect your product to a grounded
of it?
socket which is being protected by a
fuse with the appropriate capacity.
2.Please install the 2 plastic wedges as
Important:
illustrated in the figure. Plastic wedges
• The connection must be in compliance
will provide the required distance
with national regulations.
between your refrigerator and the wall
in order to allow the air circulation.
• The power cable plug must be easily
accessible after installation.
8
EN
• The specified voltage must be equal to
Placing and Installation
your mains voltage.
A If the entrance door of the room where
• Extension cables and multiway plugs
the refrigerator will be installed is not
must not be used for connection.
wide enough for the refrigerator to
BA damaged power cable must be
pass through, then call the authorised
replaced by a qualified electrician.
service to have them remove the
doors of your refrigerator and pass it
BProduct must not be operated before it
sideways through the door.
is repaired! There is danger of electric
shock!
1. Install your refrigerator to a place that
allows ease of use.
Disposing of the packaging
2. Keep your refrigerator away from heat
The packing materials may be
sources, humid places and direct
dangerous for children. Keep the
sunlight.
packing materials out of the reach
3. There must be appropriate air
of children or dispose of them by
ventilation around your refrigerator in
classifying them in accordance with the
order to achieve an efficient operation.
waste instructions. Do not dispose of
If the refrigerator is to be placed in a
them along with the normal household
recess in the wall, there must be at
waste.
least 5 cm distance with the ceiling
The packing of your refrigerator is
and at least 5 cm with the wall. If the
produced from recyclable materials.
floor is covered with a carpet, your
product must be elevated 2.5 cm
Disposing of your old
from the floor.
refrigerator
4. Place your refrigerator on an even floor
Dispose of your old refrigerator without
surface to prevent jolts.
giving any harm to the environment.
•You may consult your authorised dealer
or waste collection center of your
municipality about the disposal of your
refrigerator.
Before disposing of your refrigerator, cut
out the electric plug and, if there are
any locks on the door, make them
inoperable in order to protect children
against any danger.
9
EN
Replacing the interior light
bulb
Should the light fail to work switch
off at the socket outlet and pull out
the mains plug. Follow the below
instructions to check if the light bulb
has worked itself loose.
If the light still fails to work obtain
a replacement E14 screw cap type
15 Watt (Max) bulb from your local
electrical store and then fit it as follows:
1. Switch off at the socket outlet and
pull out the mains plug. You may find
it useful to remove shelves for easy
access.
2. Remove the light diffuser cover as
shown in figure (a-b).
3. Replace the burnt-out light bulb.
4. Reassemble the light diffuser cover
as shown in figure (c).
“Push firmly to ensure cover is fitted
properly.”
5. Carefully dispose of the burnt-out
light bulb immediately.
“Replacement light bulb can easily be
obtained from a good local electrical or
DIY store.”
10
EN
The shown close-tipped offset is part
Adjusting the feet
of design , it has no effect on cooling
If your refrigerator is unbalanced;
system.
You can balance your refrigerator by
turning the front legs as shown in the
illustration below. The corner where
the leg exists is lowered when you turn
it in the direction of black arrow and
raised when you turn in the opposite
direction. Taking help from someone to
slightly lift the refrigerator will facilitate
this process.
11
EN
Reversing the doors
Proceed in numerical order
5
1
4
60°
3
2
9
8
6
7
12
EN
