Cambridge Audio Multi-room speaker system: Incognito multi-room

Incognito multi-room

KP10 CU version KP10 EU version

KP10 AA-BBUS keypad

The KP10 EU version should be fitted into a standard single UK

(square) 47mm deep back-box (the stainless steel/silver KP10 EU

should be fitted into a 50–60mm deep back-box/pattress).

The KP10 CU version should be fitted into a standard single US J-

box.

The Cat5 cable running from the AH10 is terminated at the 8-way

colour-coded punch down connection on the rear face of the KP10.

Speaker cable is connected via screw terminals on the rear of

the KP10.

The KP10 should be positioned at a height of 138cm from the floor

finish (to centre of keypad) or taking into account light switch

Cat-5 cable Cat-5 cable

locations etc.

It should also be placed 25-35cm away from the outer edge of any

door frame or wall edge.

Locate away from direct, bright sunlight which may affect infra-red

performance.

Full instructions for installing your KP10 are supplied with the

keypad.

Speaker cable Speaker cable

Incognito multi-room 17

L-shaped probe used

AS10/ SS10 in-cceiling sspeakers

to check available void

Standard installation would specify AS10/SS10 ceiling mounted

space before cutting

speakers which are matched to the Incognito system for optimum

speaker holes

audio performance. However, virtually any customer-specified

speaker units may be used.

Where ceiling or wall-mounted speakers are used, care should be

taken to ensure that all building regulations are followed.

When mounting speakers flush to a ceiling or wall, ensure that

enough depth/clearance is available in the respective cavity. A

clearance of at least 80mm is necessary when mounting pairs of

AS10/SS10 speakers.

When deciding upon a ceiling or wall placement, care should be

taken to avoid joists, load bearing beams etc.

Before cutting ceiling loudspeaker holes it is suggested that the

area is tested for clearance by making an L-shaped probe from

strong wire (eg a coat hanger), drilling a small hole in the target area,

inserting the probe and slowly turning. Any obstructions will be

immediately obvious, so that the target area can be moved to a

more suitable position.

AS10/SS10

Also, locate loudspeakers taking into account location of furnishings

for optimal stereo reproduction.

207mm diameter

mounting hole

Full details of installation, connection, operation and special

features can be found in the guide that accompanies the speakers.

18 Incognito multi-room

Incognito multi-room

SYSTEM SPECIFICATIONS

Cambridge Audio’s policy is one of continuous improvement. Design and

specifications are therefore subject to change without prior notice.

AH10

VH10

No. of source inputs: 6

No. of source inputs: 6

No of loop outputs: 6

No. of loop outputs: 6

No. of external inputs/loop outputs/CCTV: 1

Source input specification: 75 ohm, composite video

No. of zones per hub: 4 main + 4 sub

Video bandwidth: 10MHz

System zone maximum (4 chained AH10s): 16 main + 16 sub

Maximum cable run to zone: 50m/150 ft

Frequency response: 20kHz–20kHz

Recommended cable type to zone: RG6/CT100 75 ohm co-axial

Trigger output: 12V @ 100mA

Required power input: Powered by AH10

Required power input: 24V dc (via supplied PS10)

Dimensions (W x D x H): 165 x 74 x 44mm

Note: second PS10 required for sub-low power

Weight (net): 0.6kg

Dimensions (W x D x H): 165 x 172 x 48

Weight (net): 1.14 kg / 2.5 lbs

Incognito multi-room 19

SYSTEM SPECIFICATIONS

KP10 EEU vversion KP10 CCU vversion

AS10

Frequency Response: 60Hz - 20kHz (+/- 2dB)

THD: <0.25% @ 5W, 1kHz

Signal/Noise ratio: > 80dB

Frequency response : 20Hz–20 Hz

Input impedance (local input): 33K Ohms

Volume control range : - 80dB 32 steps

Volume control range: 0 to -78dB in 31 steps

Bass control range : +/- 16dB 2dB steps

Pre-amp output: Variable, following volume setting

Treble control range : +/- 16dB 2 dB steps

IR passthrough: 34-40kHz and 54-58kHz frequencies supported

Balance control range : +/- 40dB 9 steps both ways

Speaker impedance: 4Ohms

IR pass-through : 34–40 kHz and 54– 58 kHz modulation

Power requirement: +24V DC @ 1A max from hub

Required power input : powered from AH10 via Cat5 cable

Weight (AS10-A): 1.4kg / 3.1lbs

Weight (AS10-P): 1.1kg / 2.4lbs

Dimensions: 240 x 75 mm, 9.4 x 3 inches

20 Incognito multi-room