Beko dcu 7332 c – страница 3
Инструкция к Сушильной Машиной Beko dcu 7332 c
5 Maintenance and cleaning
Filter Cartridge / Door Inner
Surface
Lint and fibres released from the laundry to the
air during the drying cycle are collected in the
“Filter Cartridge”.
Sensor
C Such fibre and lint are generally formed
during wearing and washing.
C Always clean the filter and the inner surfaces
of the cover after each drying process.
C You can clean the filter and filter area by
vacuum cleaner.
To clean the filter:
1. Open the loading door.
2. Remove the cover filter by pulling it up and
open the filter.
3. Clean lint, fibre, and cotton raveling by hand
or with a soft piece of cloth.
4. Close the filter and place it back into its
There are humidity sensors in your dryer that
seat.
detect whether the laundry is dry or not.
C Clogging may arise on the filter surface after
To clean the sensor:
using your machine for some time; if this
1. Open the loading door of the dryer.
occurs, wash the filter with water and dry it
2. Allow the machine to cool down if drying has
before using again.
been carried out.
3. Wipe the metal sensors with a soft cloth,
dampened with vinegar and dry them.
C Clean metal sensors 4 times a year.
A Never use solvents, cleaning agents or
similar substances when cleaning since
these materials can cause fire and explosion!
C Clean the entire inner surface of the cover
and door gasket.
41
EN
Water tank;
For the condenser;
The moisture in the damp laundry is taken from
Hot and humid air in the condenser is cooled
the laundry and condens ed. Drain the water
with the cold air from the room. Thus, the
tank after each drying cycle or during drying
humid air circulating in your dryer is condensed
when “Water tank” warning light turns on.
and then pumped into the tank.
A Condensed water is not drinkable!
C Clean the condenser after every 30 drying
A Never take out the water tank when the
cycles or once a month.
programme is running!
To clean the condenser:
If you forget to drain the water tank, your dryer
1. If a drying process has been carried out,
will stop during the following drying cycles
open the door of the machine and wait until
when the water tank is full and the “Water
it cools down.
tank” warning light will turn on. If this is the
case, press the “Start/Pause/Cancel” button to
resume the drying cycle after draining the water
tank.
*To drain the water tank:
1-Pull the drawer and remove the water tank
carefully.
2. Unlock the 2 condenser locks after opening
the kick plate.
2-Drain the water in the tank
3. Pull out the condenser.
3-If there is lint accumulation in the funnel of
the water tank, clean it under running water.
4-Place the water tank into its seat.
42
EN
4. Clean the condenser by applying pressurized
water with a shower armature and wait until
the water drains.
5. Place the condenser in its housing. Fasten
the 2 locks and make sure that they are
seated securely.
6. Close the kick plate cover.
43
EN
6 Suggested solutions for problems
Drying process takes too much time
• Meshes of the filter may be clogged. Wash with water.
Laundry comes out wet at the end of drying.
• Meshes of the filter may be clogged. Wash with water.
• Excessive laundry might have been loaded in. Do not load the dryer in excess.
Dryer does not switch on or the programme does not start. Dryer is not activated when set.
• It might have not been plugged in. Make sure that the machine is plugged in.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Programme might have not been set or the "Start/Pause/Cancel" button might have not
been pressed. Make sure that the programme has been set and it is not in “Pause” mode.
• "Childproof lock" might have been activated. Deactivate the childproof lock.
Programme has been interrupted without any cause.
• The loading door may be ajar. Make sure that the loading door is properly closed.
• Electricity may be cut off. Press "Start/Pause/Cancel" button to start the programme.
Laundry has shrunk, become felted or deteriorated.
• A programme suitable for the laundry type might have not been used. Dry only the laundry
which is suitable for drying in dryer after checking the labels on your clothes.
• Select a programme with suitable low temperature for the laundry type to dry your clothes.
Drum lightning does not come on.
• Dryer might have not been started by using the "On/Off" button. Make sure that the dryer is
on.
• Bulb may have blown. Call the authorized service to replace the bulb.
“Final / Anti-creasing” symbol flashes.
• The 2-hour anti creasing programme to prevent laundry from creasing might have been
activated. Turn off the dryer and take out the laundry.
“Final / Anti-creasing” symbol is on.
• Programme has come to an end. Turn off the dryer and take out the laundry.
Water comes out the cover.
• Clean the entire inner surface of the cover and door gasket.
Cover opens spontaneously.
• Push it until you hear that it is closed.
For products with a condenser:
“Water tank” warning symbol is on.
• Water may be full.
• Anti-creasing programme might be running. Drain the water in the tank.
“Filter cleaning” symbol is on.
• Filter might have not been cleaned. Clean the cover filter.
“Condenser cleaning” symbol is on.
• Filter drawer/Condenser might have not been cleaned. Clean the filters in the condenser/filter
drawer under the kick plate.
A Call an authorised service if the problem persists.
44
EN
