Главная > Инструкция к Стиральной машиной Стандартной Beko WKD 25100 T > Installation

Beko WKD 25100 T: Installation

Installation: Beko WKD 25100 T

Installation

6

If your system is not ready, let a certified plumber make it

2. Leveling the feet

ready.

In order to operate your machine without noise and vibra-

tion it must be properly on balance. Four feet of your ma-

1. Removing the transportation safety bolts

chinecanbeadjusted.Firstloosentheplasticcounterbolt.

Tightenthecounterboltafteradjustingthefeetforleveling

Beforethewashingmachineisoperated,thetransitbars

your machine.

must be removed! In order to do this:

1. Loosen “C” bolts by rotating them counter clockwise

with a suitable spanner

3. Water Connections

2. Remove transportation safety bolts by turning.

3. Place “P” plastic covers onto the openings of transpor-

a) Water Inlet Hose

tation locks by rotating in direction of arrow and pushing.

Yourmachineisconnectedtowatersupplybyspecial

hoses supplied by the machine. Red hose or hose

Attention please! Keep the transit bars for using when

written red on it is hot water inlet, blue hose or hose

machine is to be transported again. Always transport your

written blue on it is cold water inlet.

machine with transportation locks.

There are plastic seals (4 for double water inlet mod-

els, 2 for single water inlet models) on hose or plastic

bag for eliminating any leakage in connections points.

These seals must be used on each side of the connec-

20

tion. Seals on machine side must be connected filter

cannal.

Do not connect single inlet machine to hot water. If

machineisconnectedwithYparttoadoubleinlet

After connecting the hose, check all connections for

andover40˚Cforsingleinletmachines,machinemay

leaks In order to eliminate any risk due to water leakage

switch to protection mode.

keep the taps off when machine is not used.

b) Water drain hose

Water drain hose could be placed either at the side of the

bath tub, or directly to the drain. The hose should not be

bent. Water drain hose should be secured with the holder

so that it would not fall down on the ground.

The hose should be placed between 40 and 100 cm. from

the ground.

Yourmachinewilloperateefficientlyifthewaterfrom

Water drain hose could be placed directly to the drain

tap is minimum 1 and maximum 10 bars. Practically 1

water inlet.

bar means 8 liters of water in one minute when tap is

fully on.

Connect hose to the machine. Tighten bolts with hand

power, do not use spanner.

Double inlet models can be used with blind cap as a

single inlet machine. Connect blind cap to hot water

inlet. Seal must be for stopping water leakage.

21

4. Electrical connection

Connect the power cord to the appropirate electrical sys-

tem which is being supported by the maximum voltage and

current rating indicated on the rating plate placed inside the

kick plate.

Look! Page 1, Steps before operating Fullautomatic Wash-

ing Machine and safety precautions.

Make sure that you have grounded power outlet.

Attention!Beforeanyoperationofthemachinecheckthe

following.

•Didyouclosethefrontdoor?

•Isthetapopen?

•Iswaterdrainhoseplacedproperly?

•Ispowerconnected?

22

Оглавление

Топ 10 инструкций

Другие инструкции

Beko WKD 25080 T Beko WKD 25080 T Beko WKD 25085 T Beko WKD 25085 T Beko WKD 25105 T Beko WKD 25105 T Beko WKD 25105 TS Beko WKD 25105 TS Supra BSS-6900 Supra BSS-6900 Bosch WLX 20162 OE Bosch WLX 20162 OE