Beko FSE 21906: 3 Installation
3 Installation : Beko FSE 21906
3 Installation
B Please remember that the
manufacturer shall not be held liable if
the information given in the instruction
manual is not observed.
Points to be considered
when re-transporting your
freezer
1. Your freezer must be emptied and
cleaned prior to any transportation.
2. Shelves, accessories, crisper and
etc. in your freezer must be fastened
3. Clean the interior of the freezer as
securely by adhesive tape against any
recommended in the “Maintenance
jolt before repackaging.
and cleaning” section.
3. Packaging must be tied with thick
4. Plug the freezer into the wall outlet.
tapes and strong ropes and the
When the fridge door is open the
rules of transportation printed on the
fridge compartment interior light will
package must be followed.
come on.
Please do not forget…
5. You will hear a noise as the
Every recycled material is an
compressor starts up. The liquid and
indispensable source for the nature
gases sealed within the refrigeration
and for our national resources.
system may also give rise to noise,
If you wish to contribute to recycling
even if the compressor is not running
the packaging materials, you can
and this is quite normal.
get further information from the
6. Front edges of the freezer may feel
environmental bodies or local
warm. This is normal. These areas
authorities.
are designed to be warm to avoid
Before operating your
condensation.
freezer
Electric connection
Before starting to use your freezer
Connect your product to a grounded
check the following:
socket which is being protected by a
1. Is the interior of the freezer dry and
fuse with the appropriate capacity.
can the air circulate freely in the rear
Important:
of it?
• The connection must be in
2. You can install the 2 plastic wedges
compliance with national regulations.
as illustrated in the figure. Plastic
• The power cable plug must be easily
wedges will provide the required
accessible after installation.
distance between your freezer and
• The specified voltage must be equal
the wall in order to allow the air
to your mains voltage.
circulation. (The illustrated figure is
• Extension cables and multiway plugs
only an example and does not match
must not be used for connection.
exactly with your product.)
8
EN
in the wall, there must be at least 5 cm
B A damaged power cable must be
distance with the ceiling and at least 5
replaced by a qualified electrician.
cm with the wall.
B Product must not be operated before
If the floor is covered with a carpet,
it is repaired! There is danger of
your product must be elevated 2.5 cm
electric shock!
from the floor.
Disposing of the packaging
4. Place your freezer on an even floor
The packing materials may be
surface to prevent jolts.
dangerous for children. Keep the
packing materials out of the reach
5. Do not keep your freezer in ambient
of children or dispose them of by
temperatures under 10°C.
classifying them in accordance
with the waste instructions. Do not
dispose them of along with the normal
household waste.
The packing of your freezer is
produced from recyclable materials.
Disposing of your old freezer
Dispose of your old machine without
giving any harm to the environment.
• You may consult your authorized
dealer or waste collection center of
your municipality about the disposal
of your freezer.
Before disposing of your freezer, cut
out the electric plug and, if there are
any locks on the door, make them
inoperable in order to protect children
against any danger.
Placing and Installation
1. Install your freezer to a place that
allows ease of use.
2. Keep your freezer away from heat
sources, humid places and direct
sunlight.
3. There must be appropriate air
ventilation around your freezer in order
to achieve an efficient operation.
If the freezer is to be placed in a recess
9
EN
C This appliance is designed to
Adjusting the legs
operate at temperatures specified
If your freezer is unbalanced;
in the table below is equipped with
You can balance your freezer by
Advanced Electronic Temperature
turning the front legs of it as illustrated
Control System [AETCS] which
in the figure. The corner where the
ensures that at the advised setting [4
leg exists is lowered when you turn
- four on the knob] the frozen food in
in the direction of black arrow and
the freezer will not defrost even if the
raised when you turn in the opposite
ambient temperature falls as low as
direction. Taking help from someone to
-15 °C.
slightly lift the freezer will facilitate this
When first installed the product
process.
MUST NOT be placed in low ambient
temperatures because the freezer will
not reduce to it’s standard operating
temperature. Once it has reached its
steady operating state it can be re-
located.
So you may then install your appliance
in a garage or an unheated room
without having to worry about frozen
food in the freezer being spoilt.
However at low ambient temperatures
mentioned above, fridge contents are
likely to freeze, so check and consume
food in the fridge accordingly. When
the ambient temperature returns to
normal, you may change the knob
setting to suit your needs.
C If the ambient temperature is
below 0°C, the food in the fridge
compartment will freeze.So, we
recommend you don’t use the fridge
compartment in such low ambient
conditions. You can continue using the
freezer compartment as usual.
10
EN
Reversing the doors
Proceed in numerical order .
(12)
5
2
3
1
6
4
45 °
8
7
9
16
12
13
180°
15
16
14
11
10
11
EN
Оглавление
- FSE 21906
- 1 Your Freezer
- 2 Important Safety Warnings
- 3 Installation
- 4 Preparation
- 5 Using your freezer
- 6 Maintenance and cleaning
- 7 Recommended solutions for the problems
- 1 Описание морозильника
- 2 Важные указания по технике безопасности
- 3 Установка
- 4 Подготовка
- 5 Пользование морозильником
- • Внимание!
- 6 Обслуживание и чистка
- 7 Рекомендации по устранению неполадок