Gorenje DF 6116 BX: Installation Electrical connection Mounting Preliminary information for installation of the hood:

The brackets are one right R and one left L (see bossing

Installation

shown on the brackets).

The minimum distance between the supporting surface for the

1. Fix the D bracket (Fig.1) to the side panel of the wall unit

cooking equipment on the hob and the lowest part of the

with two screws for every bracket (the right R bracket on

range hood must be not less than 60cm from electric cookers

the right side and the left L bracket on the left side).

and 70cm from gas or mixed cookers.

Align the bracket with the lower border.

If the instructions for installation for the gas hob specify a

Position the bracket to touch the back border of the wall

greater distance, this must be adhered to.

cabinet, considering that the back border of the bracket

corresponds to the back side of the cooker hood;

Electrical connection

If the cooker hood is provided with a spacer, in case of

The mains power supply must correspond to the rating

use, move the bracket forward to the same thickness as

indicated on the plate situated inside the hood. If provided with

the spacer.

a plug connect the hood to a socket in compliance with current

Drill a hole on the ceiling of the wall cabinet to pass the

regulations and positioned in an accessible area. If it not fitted

discharge tube and the electrical cable (the quote

with a plug (direct mains connection) or if the plug is not

indicated in Fig. 1 does not include the eventual spacer).

located in an accessible area apply a double pole switch in

2. If not already mounted, fix the two E brackets (Fig.2) to

accordance with standards which assures the complete

the sides of the hood (one per side).

disconnection of the mains under conditions relating to over-

a. remove the extractable part of the cooker hood;

current category III, in accordance with installation

b. remove the grease filter/s;

instructions.

c. fix the brackets with two screws P per bracket from

Warning! Before re-connecting the hood circuit to the mains

inside the cooker hood, affix them as more as possible

supply and checking the efficient function, always check that

upwards (air exit side) and then serrate the screws.

the mains cable is correctly assembled.

3. Affix the spacer M with three Clips from the external part

of the cooker hood (if supplied - Fig. 2).

Mounting

4. Insert the cooker hood in the wall cabinet, ensuring to

Before beginning installation:

position the cooker hood bracket E above the wall

• Check that the product purchased is of a suitable size for

cabinet bracket D (Fig. 3).

the chosen installation area.

Thread the electric cable through the appropriate

• To facilitate installation, remove the fat filters and the

perforation.

other parts allowed and described here, dismantle and

5. Block the cooker hood with two screws on the frontal part

mount it.

(Fig. 3 – one per side).

To remove see also the relative paragraphs.

6. Connect the cable to the electrical mains, only when the

• Remove the active carbon (*) filter/s if supplied (see also

installation is completed.

relative paragraph). This/these is/are to be mounted only

7. If the cooker hood should not touch perfectly with the

if you want lo use the hood in the filtering version.

lower border of the wall cabinet then regulate by

• Check (for transport reasons) that there is no other

loosening the screws P of the brackets E mounted on the

supplied material inside the hood (e.g. packets with

cooker hood (Fig. 2), it will be possible to regulate the

screws (*), guarantees (*), etc.), eventually removing

perfect matching of the cooker hood and wall cabinet,

them and keeping them.

once regulated tighten the screws.

• If possible, disconnect and move freestanding or slide-in

8. Regulate the gliding of the extractable drawer in relation

range from cabinet opening to provide easier access to

to the depth of the wall cabinet by acting on the two

rear wall/ceiling. Otherwise put a thick, protective

skirting boards F (Fig. 4).

covering over countertop, cooktop or range to protect

In this way it will be possible to place the front in line with

from damage and debris. Select a flat surface for

the wall cabinet (Fig. 4).

assembling the unit. Cover that surface with a protective

a. Loosen the screws on the skirting board F;

covering and place all canopy hood parts and hardware

b. Move the ledges backwards or forwards depending on

in it.

requirement.

• In addition check whether near the installation area of the

c. Lock in the screws on the ledges.

hood (in the area accessible also with the hood mounted)

9. Install a discharge tube on the connection ring C

an electric socket is available and it is possible to

supplied, preferably with a diameter equivalent to the

connect a fumes discharge device to the outside (only

connection ring (Fig. 5). the discharge tube should be

suction version).

sufficiently long to reach outside (Suction version) or the

• Carry out all the masonry work necessary (e.g.

ceiling of the wall cabinet (Filter version).

installation of an electric socket and/or a hole for the

10. Fix the connection ring C (snap into place), at the upper

passage of the discharge tube).

exit of the cooker hood.

Preliminary information for installation of the hood:

To ease the installation, the ring is equipped with an

Attention! The 2 fixing brackets are lodged in the protection

index G that should correspond to the appropriate guide

in polyester packing

H placed on the upper air exit.

10