LED LENSER H14.2: LED LENSER® * H14.2

LED LENSER® * H14.2

function). A short flash indicates the darkest (5

8. Reset function

lumens) or brightest setting.

If the alkaline batteries are taken out the battery

In the Pulse - function, you can speed up or

box you have "reset" the H7. You have thus reset

slow down the flashing frequency by turning the

a few functions so that the “Transport Lock” (see

multi-function "Wheel" switch (Pulse function).

Section 6) is deactivated and the Light Function

Dim (see Section 5.1) is set to low brightness.

d) Boost Mode: in any state, push the front

switch for 2 seconds to achieve boost mode.

9. Changing of the Alkaline batteries

After 10 seconds the flashlight will return to the

Prior to the change, turn off the H14.2.

previous setting.

On the back of the battery back, where the

headband is attached, there is the gate to the

The Light Functions above are in a loop.

inside of the battery box. Open the battery box

Note that when switching modes, press the

rear cover, remove the battery, and then insert

“Multi-function Wheel” switch on the back for no

a new one.

longer than 2 seconds, otherwise the product

Insert a new one (4 AA alkaline batteries/ 4 AA

will turn off.

Ni-MH rechargeable batteries/ 4 cr123a alkaline

batteries/ 2 ICR18650 Li-ion battery packs can

6. Energy Modes

be used on the product) .

By selecting one of the two Energy Modes

Please notice, do not charge the alkaline battery!

(Energy Saving or Constant Current), you take

During insertion, it is always necessary that it is

a decision on how the energy contained in the

in the correct direction. Therefore, pay attention

accumulator respectively in the batteries is

to the polarities (+ and -) both on the battery

used.

box and the alkaline batteries. Otherwise, there

is a risk for damage batteries and a possible

6.1 Energy Saving: The light output is controlled

explosion.

by the integrated Smart Light Technology (SLT).

After replacing the batteries, the cover of the

The brightness is matched to the real conditions

battery box has to be put back into place.

that occur during normal use of the lamp, thus

providing a longer burn time.

10. Headband

The headband can be washed by water.

6.2 Constant Current: This Energy Mode allows

Please refer to the picture to disassemble and

the continuous use of all the Light Functions

assemble the headband.

with a more or less constant light output. This

Energy Mode is to be preferred when a high

11. Batteries

brightness level is more important than a long

Never use non rechargeable batteries and

burn time.

accumulators together.

Change always all batteries at the same time.

Changing of the Energy Modes

Use in the H14.2R below batteries can be

For changing the Energy Modes, only can be

used 4xAA alkaline/ 4xAA Ni-MH/ 4Xcr123A

active when the flashlight in the Light Program

alkaline/ 4xCR123A rechargeable/ 2xICR 18650

White. Keep the LED off, and then switch the

batteries/ 2xICR 18650 Li-ion battery pack.

“Multi-function Wheel” switch on the back for 8

If you intend not to use the item for an extended

times and keep it pressed for approx. 2 seconds.

period, please take out the batteries in order to

Then you change the mode between „energy

avoid damage.

mode“ and „constant current mode“.

Used batteries and accumulators have to be

a) Constant current mode: In case the

taken out the item and disposed of in keeping

brightness reduces immediately in 2 seconds,

with the national laws.

the H14.2 is on constant current mode;

b) Energy saving mode: in case the brightness

12. Cleaning

reduce gradually to zero, the H14.2 is in the

To clean, use a dry, lint-free, clean cloth.

Energy Mode.

If salt water is spilled on the head lamp, it must

With this procedure, you can switch between

be immediately entirely removed with such a

the two Energy Modes. It is not possible to

cloth.

determine in which Energy Mode the H14.2

The headband can be washed in a washing

is. To find this out, you must carry out the

machine at 30 °C.

procedure. If the H14.2 is thereafter not in the

desired Energy Mode any more, you must repeat

13. Scope of delivery

the procedure again. The flashlight will reset to

The H14.2 headlamp is supplied with the

energy saving mode if you change the battery or

following accessories:

cut the power.

1 H14.2 headband

4 AA alkaline batteries

7. „Transport Lock“

1 user manual

When the H14.2 is off, push the front switch

for approx. 5 seconds till the light turns off

14. Caution

in order to enable the “Transport Lock.” The

Do not swallow any small parts or batteries/

H714.2 therefore cannot be switched on; either

accumulators that are present. The products

intentionally or unintentionally and inadvertently

or parts thereof (including batteries /

consume energy.

accumulators) must be stored out of the reach

To deactivate the “Transport Lock”, just press

of children.

the front switch again for 5 seconds. The

For safety and approval reasons (CE), the

headlamp will now return to the Light Program.

product must not be modified and/or changed.

The product is to be used exclusively as an

03

GB

accumulator or battery powered lamp. If

subside depends primarily on the brightness

the H14.2 is used for any other purpose, or

between the blinding-light source and the

incorrectly, it can get damaged and a hazard-

surrounding area. Photosensitive people in

free use is no longer guaranteed (danger from

particular ought to consult a medical consultant

fire, short-circuit, electric shock etc.) and

prior to using this product.

therefore there will be no liability for harm

As a matter of principle the rule is that high-

anyone or damage to property. The warranty of

intensity light sources carry a high secondary

the manufacturer is also rendered null and void.

hazard potential due to their blinding effect.

The H14.2 can be operated between -20 C° and

Just like looking into other bright light sources

+50 C° (or between -4 F° and 122 F°). Ensure

(e.g. headlights of a car), the temporary limited

that the H14.2 is not subjected to more extreme

impairment of vision and afterimages may lead

temperatures, intense vibrations, explosive

to irritation, inconveniences, impairments and

atmosphere, solvents and/or vapors. Also

even accidents, depending on the situation.

continuous exposure to direct sunlight, high

humidity and/or moisture must be avoided.

This information applies to the use of a single

Changes, repairs and maintenance over and

product. If more light-emitting products of

above those described in the documents

the same type or of a different type are used

accompanying the product may only be carried

together, the intensity of the optical radiation

out by authorized technical personnel.

may increase.

If it is found that the product is filled with

Every long view/eye-contact with the source

full batteries / accumulators in the correct

of radiation of this product by the user or other

orientation (polarity!) and properly closed, and

persons, with and without other light-bundling

still unable to be function safely and normally,

instruments, is to be avoided as a matter of

or the product shows damage, it must be

principle! Instead, the eyes are to be closed

rendered inoperable and not used any further.

deliberately in such cases and the head ought to

In this case, for warranty matters, contact your

be turned away from the light beam.

dealer.

In case of a commercial use or the product’s use

by public bodies, the user must be instructed to

15. Safety instructions

follow all applicable laws and regulations that

This product is not a children's toy.

correspond to the individual case of usage.

Since it has small parts that can be swallowed,

it is especially not suitable for those under the

Important rules of conduct:

age of 5.

Do not aim the light beam directly into the eyes

The article may not be used for examinations of

of a person.

the eyes (e.g. for a pupil test).

The user or any other person should not look

When in use, heat accumulation, e.g. by

directly into the light beam.

covering, must be avoided.

In the event of optical radiation hitting the eye,

If the product does not work correctly, the first

one must shut their eyes and turn their head

thing that must be checked is whether this is

away from the beam.

due to discharged or incorrectly placed battery/

The instruction manual and this information

accumulators.

must be stored safely and must always be kept

If using in traffic, please follow the respective

together with the product.

legal regulations.

It is prohibited to look straight into the light that

The most hazardous threat posed by this

is being emitted by this product.

product is the optical radiation known as

Blue Light Hazard (400 nm to 500 nm). The

thermal hazard threshold values are not clearly

determined yet.

The risk for the viewer depends on the use or

on how the product is installed. However, there

is no optical hazard as long as there is a limit

on the time of exposure and the information

contained in this instruction manual is observed.

The aversion reactions are triggered by the

exposure and they are a natural reaction that

protects the eye from hazards through optical

radiation. This includes in particular conscious

aversion reactions such as eye or head

movement (e.g. turning away).

When using the product it is of particular

importance to bear in mind that the aversion

reactions of person at whom the light is directed

at may be weakened or completely suspended

as a result of medication, drugs or illness.

Because of the blinding effect of the product,

improper use may lead to reversible, i.e.

temporary impairment of sight (physiological

blinding) or afterimages, or it may trigger

queasiness and fatigue (through physiological

blinding). The intensity of the temporary

discomfort or the time until the side effects

04