Babyliss E763XDE/764XDE Hair clipper: ENGLISH

hours before using it for the rst

ENGLISH

time and then approximately

every three months. Full

CLIPPER E763XDE

autonomy of the unit will only be

1. 2 cutting guides for 22

obtained after three complete

lenghts (from 3 to 18mm and

recharge cycles.

from 21 to 36mm, in 1.5mm

steps)

CHARGING THE CLIPPER

2. 1 precision guide

Before using the clipper for the

5 positions (0.5 to 2.5mm)

rst time, allow it to charge for 16

3. Blades:

hours.

Moveable blade:

1. Connect the transformer to the

- Sharpened using 3D etching

mains and the plug into the

process: for an exceptionally

unit. (Fig. 1)

sharp cutting edge.

2. Check that the charging

- CMS (Chrome-Molybdenum-

indicator light is lit and that the

Stainless Steel): ultra-hardwearing

switch on the trimmer is in the

and 100% stainless steel blade.

OFF position.

Fixed Blade:

3. A fully charged trimmer will run

- Titanium coating: for longer

for 30 minutes.

life.

These two technologies provide

MAINS USE

perfect surface condition and their

Connect the transformer into the

combination is optimal for reducing

mains, wait 1 minute and then

the friction coecient.

switch into the ON position.

4. Thinning function

5. Turbo function

IMPORTANT! Use only the

6. ON/OFF switch

transformer provided with the

7. Cutting length control knob

E763XDE clipper Voltage = 3.0V -

8. Lateral display of selected

Tension = 1000mA

length

9. Charging indicator light

TURBO

10. Plug for use on the mains

For an extra burst of power,

and for charging

push the TURBO button on the

11. Cleaning brush and comb

top side of the clipper. This will

boost the motor of your clipper,

IMPORTANT INFORMATION

producing faster cutting action

REGARDING THE NI-MH

and increased cutting power for

BATTERIES OF THIS UNIT

the more dicult cutting tasks.

To obtain and maintain the

longest battery autonomy

possible, allow it to charge for 16

7

USING THE CUTTING GUIDES

CUTTING TECHNIQUES AND

Very practical, the cutting guide

ADVICE FROM THE EXPERTS

guarantees equal cutting length.

• Use the clipper on clean, dry

IMPORTANT: Always attach the

hair.

cutting guide BEFORE turning the

• To familiarize yourself with the

trimmer on, and turn it o before

clipper, begin with the cutting

changing the guide.

guide for a longer cut, then, if

you want a shorter cut, adjust

To attach the cutting guide,

it by pushing the knob. You will

rst adjust the cutting length to

soon know the lengths of each

3mm or 21mm and place it on

guide and each position.

the support guide adjusting rst

• Always move the clipper against

both sides and then pushing on

the direction of hair growth.

the bottom of the guide until you

• Begin at the nape. Place the

hear a ‘click’. (Fig. 2)

guide on the scalp and move the

clipper toward the crown of your

To remove the cutting guide, rst

head. Move your clipper slowly,

adjust the cutting length to 3mm

pointing the teeth of the guide

or 21mm and push the guide out

slightly upward. Keep the clipper

of the support lifting it up with

in contact with your head at all

your thumb. (Fig. 3)

times. (Fig. 4)

• For the crown of the head, move

NOTE: The precision guide must

from front to back, that is, from

be placed like the cutting guides

your forehead to the crown of

but it is adjusted manually and

your head.

independently of the grooved

• For the nishing touches, that is,

wheel.

around the nape and sideburns,

use the clipper without a cutting

TURNING ON AND USING

guide. Turn your clipper over

To adjust the clipper’s cutting

and move it from top to bottom.

length, turn the grooved wheel

(Fig. 5)

(7) up or down.

The selected length is displayed

• If you want a length greater than

on the right or left side of the

30 mm, or if you are experienced,

clipper.

you can create ‘comb’ or ‘nger’

Switch the ON/OFF button.

cuts:

You can change the cutting length

- Work without a cutting guide.

at any time.

- Take up a small section of hair

Thanks to the SMART ADJUSTING

with a comb or in your ngers.

SYSTEM, the length of the cut is

- Move the comb or your ngers

maintained even if the angle of

along the section of hair to the

the clipper varies, so it guarantees

desired length.

precise result.

8

- Cut your hair along the comb or

Self-lubricating blades

your ngers.

The blades of your clipper have

- Remove the cut hair using a

a reservoir pad that dispenses

comb and check the evenness of

the amount of oil necessary for

the cut regularly. (Fig. 6)

your clipper to operate properly,

every time. It is nevertheless

Using the thinning guide

recommended that you occa-

Switch the clipper to the ‘THIN’

sionally rell, when you notice the

position. The thinning guide is in

clipper isn’t performing as well.

front of the blades.

Remove the blades as described

This technique allows you to thin

above.

out hair to make styling easier.

Carefully squeeze a few drops of

The technique is particularly good

BaByliss oil onto the pad. (Fig. 8)

for the crown of the head where

Then put the blades back on the

hair is usually thicker.

clipper.

To thin you hair, take a section

BaByliss oil is specially formulated

of hair (rest your little and ring

for clippers, it will not evaporate

ngers on your scalp, using the

or slow the blades down.

middle and index ngers to set

You can get new blades when

the length), hold 1 to 2 cm below

these are worn or damaged.

the cutting length. Then, using

the clipper, cut the section of hair

steeply and at an angle to create a

saw-toothed ‘edge’.

MAINTENANCE

Remove the cutting guide after

each use.

Cleaning the clipper blades

regularly will maintain their

optimal performance.

Removable blades

To make cleaning easier, the

BaByliss clipper blades can be

removed. Make sure the clipper

is turned o. Hold the clipper

with the blades pointing up and

remove them by pressing the top

of the blade. (Fig. 7)

Brush the blades using the

cleaning brush to remove any

hair.

9