HP Designjet 10000s Printer series: III Safety III 11 General iinformation III 22 Use aas iintended III 33 Information oon ssigns aand ssymbols
III Safety III 11 General iinformation III 22 Use aas iintended III 33 Information oon ssigns aand ssymbols: HP Designjet 10000s Printer series
Table of contents
- I Introduction
- II Product ddescription
- III Safety III 11 General iinformation III 22 Use aas iintended III 33 Information oon ssigns aand ssymbols
- III 44 Warnings
- III 55 Warnings ffor mmaintenance III 66 Protective eequipment
- Index
- 1 Installation && FFunction DDescription 1.1 Warnings ffor mmaintenance
- 1.2 Unpacking aand iinstallation 1.3 Box ccontent
- 1.4 Connection oof tthe pprinter 1.5 Power oon tthe AAPS 1.6 Function ddescription
- 2 Operation 2.1 Operating cconditions 2.2 Operation
- 2.3 Test ooperation
- Designation
- Figure 1 Figure 2 Figure 3
- Figure 4 3.3.2 IInsert tthe nnew ffilter(s) Figure 5 Figure 6 Figure 7
- 3.4 Enter tthe ccode oof tthe nnew rreplacement ffilter 3.4.1 HHP DDesignjet 88000s AAir PPurifier SSystem
- 3.4.2 HP DDesignjet 99000s/10000s AAir PPurifier SSystem
- 4 Disposal
- 5 Troubleshooting
- 6 Legal iinformation
- 6.Your exclusive remedies for defective HP products are the following:
- B. Limitations of liability C. Local law
- 7 Regulatory nnotices 7.1 Regulatory mmodel nnumber 7.2 Regulatory sstatements
- 9 Technical ddata
III Safety
III 11 General iinformation
The APS is built in accordance with state of the art technology and adherence to safety rules.
Nevertheless, during use there may be dangers to the user or a third parties if it is not used for
the purpose for which it was intended, and not properly maintained.
III 22 Use aas iintended
The APS may only be operated with the HP printers for which it is designed.
The work area where the HP Designjet 8000s or 9000s/10000s printer is used must be ade-
quately ventilated. The APS is not a substitute for ventilation of the work area.
The APS is not intended to be used as a substitute for adequate ventilation of the work area.
The APS removes
v
olatile
o
rganic
c
ompounds (VOC's ) released inside the printer during ope-
ration, but prints that are drying and being stored also release VOC's. The APS only reduces
the release of volatile organic compounds in the work area from the printer and it is not inten-
ded under any circumstances to be used in closed room without ventilation.
Any other use other than direct connection to an HP Designjet 8000s and 9000s/10000s prin-
ter is not considered to be proper use of the APS.
This also applies for unauthorized modifications to the APS. In particular in the case of replace-
ment filter elements purchased from third parties, there is no guarantee that performance will
meet HP specifications.
Proper use includes compliance with the information:
- on safety,
- on operation and
- on maintenance,
as described in this user's guide
III 33 Information oon ssigns aand ssymbols
The following designations or symbols for safety information and particularly important details
are used in these operating instructions:
Warning!
Failure to follow the guidelines marked with this symbol could result in serious perso
nal injury or death
Caution!
Failure to follow the guidelines marked with this symbol could result in minor personal
injury or damage to the product.
Note
Additional information for a safe, proper and efficient handling of the APS.
• Work and/or operating steps are marked with the large reference point. The
steps are to be executed in the order from top to bottom!
– Lists are marked with the dash.
All information should be complied with, for the proper use of the APS. Please be sure all ope-
rators of the APS are completely familiar with information in this manual.
Information and symbols directly attached to the APS, such as warning signs, warning stickers
component part markings etc must be observed.
The information and symbols directly attached to the APS may not be removed and must be kept
in a completely readable condition.
6 User´s Guide
