HP Designjet 10000s Printer series: Designation
Designation: HP Designjet 10000s Printer series
Table of contents
- I Introduction
- II Product ddescription
- III Safety III 11 General iinformation III 22 Use aas iintended III 33 Information oon ssigns aand ssymbols
- III 44 Warnings
- III 55 Warnings ffor mmaintenance III 66 Protective eequipment
- Index
- 1 Installation && FFunction DDescription 1.1 Warnings ffor mmaintenance
- 1.2 Unpacking aand iinstallation 1.3 Box ccontent
- 1.4 Connection oof tthe pprinter 1.5 Power oon tthe AAPS 1.6 Function ddescription
- 2 Operation 2.1 Operating cconditions 2.2 Operation
- 2.3 Test ooperation
- Designation
- Figure 1 Figure 2 Figure 3
- Figure 4 3.3.2 IInsert tthe nnew ffilter(s) Figure 5 Figure 6 Figure 7
- 3.4 Enter tthe ccode oof tthe nnew rreplacement ffilter 3.4.1 HHP DDesignjet 88000s AAir PPurifier SSystem
- 3.4.2 HP DDesignjet 99000s/10000s AAir PPurifier SSystem
- 4 Disposal
- 5 Troubleshooting
- 6 Legal iinformation
- 6.Your exclusive remedies for defective HP products are the following:
- B. Limitations of liability C. Local law
- 7 Regulatory nnotices 7.1 Regulatory mmodel nnumber 7.2 Regulatory sstatements
- 9 Technical ddata
3 Maintenance
3.1 General iinformation
Warning!
Used filters capture an organic solvent (ethylene glycol monobutyl ether acetate, CAS
No. 112-07-2) and other chemicals from ink vapors. When disposing used filter car--
tridges it is your responsibility to observe all local, state, and federal regulations rela-
ted to the handling, use, storage, and disposal of organic solvents.
Warning!
You must remove the power supply cable on the APS during cleaning and service work.
Note:
Please also follow the safety instructions in section III Safety.
3.2 Routine mmaintenance wwork
You must inspect the accessible areas of the APS daily for damage and assess the APS for pro-
per operation
Caution!
– Labels and control elements or warning signs may become illegible through un--
avoidable dirt deposits. This can lead to faulty operation, which may cause a safety
hazard.
– It is recommended to clean control elements, displays and warning stickers once a
week removing accumulated dust and other dirt by wiping with a clean, damp
cloth. Avoid using an excessively wet cloth that may release liquids into the APS.
– Avoid the use of solvent cleaners, which may attack elements of the keypad, dis
play, gaskets, or paint. Only water-based cleaners or soapy water are recommen
ded.
– Do not allow liquids to spill into or penetrate into the APS.
3.3 Replacement oof ffilters
The filter elements must be replaced after an interval period of 800 operating hours. The dis-
play of the filter contamination in the transparent display shows in this case 100 % and the red
LED (Error) will light permanently. All activated carbon filters will become full at different speeds
depending on type of use, and they should be replaced between 700 and 800 operating
hours, and no later than 800 hours under any circumstance. For ordering new filters:
15HP Air Purifier System
Designation
Product NNumber
HP Designjet 8000s / 9000s/10000s APS Filter
Q6679 A
(HP Designjet 8000s Air Purifier system,
1x filter element required)
(HP Designjet 9000s/10000s Air Purifier system,
2x filter elements required )
