HP Designjet 10000s Printer series: 1 Installation && FFunction DDescription 1.1 Warnings ffor mmaintenance
1 Installation && FFunction DDescription 1.1 Warnings ffor mmaintenance: HP Designjet 10000s Printer series
Table of contents
- I Introduction
- II Product ddescription
- III Safety III 11 General iinformation III 22 Use aas iintended III 33 Information oon ssigns aand ssymbols
- III 44 Warnings
- III 55 Warnings ffor mmaintenance III 66 Protective eequipment
- Index
- 1 Installation && FFunction DDescription 1.1 Warnings ffor mmaintenance
- 1.2 Unpacking aand iinstallation 1.3 Box ccontent
- 1.4 Connection oof tthe pprinter 1.5 Power oon tthe AAPS 1.6 Function ddescription
- 2 Operation 2.1 Operating cconditions 2.2 Operation
- 2.3 Test ooperation
- Designation
- Figure 1 Figure 2 Figure 3
- Figure 4 3.3.2 IInsert tthe nnew ffilter(s) Figure 5 Figure 6 Figure 7
- 3.4 Enter tthe ccode oof tthe nnew rreplacement ffilter 3.4.1 HHP DDesignjet 88000s AAir PPurifier SSystem
- 3.4.2 HP DDesignjet 99000s/10000s AAir PPurifier SSystem
- 4 Disposal
- 5 Troubleshooting
- 6 Legal iinformation
- 6.Your exclusive remedies for defective HP products are the following:
- B. Limitations of liability C. Local law
- 7 Regulatory nnotices 7.1 Regulatory mmodel nnumber 7.2 Regulatory sstatements
- 9 Technical ddata
1 Installation && FFunction DDescription
1.1 Warnings ffor mmaintenance
The APS is delivered upright on a wooden pallet according to the IPPC standard. The following
industrial trucks are permitted for transporting the wooden pallets:
– Fork lift trucks and
– Fork stacker lift trucks.
Do not drop the APS during handling.
Secure the wooden pallets with the upright APS during transport to prevent the APS from falling
over.
Observe the applicable accident prevention and labour safety regulations.
You must observe the information on the packaging.
The APS or the wooden pallet with the APS is to be secured on the transport vehicle against slip-
ping and falling over.
Warning!
If the wooden pallets are not secured properly the APS may fall down and cause seri-
ous injury or death.
Only use suitable hoisting equipment and securing means!
The driver must be authorized to steer the industrial truck.
Drive between the spans of the wooden pallet using the fork lift truck.
Observe the following information for transporting the APS:
– The fork lift truck must be permitted for the total weight of the wooden pallets with
upright APS.
– Weight of the complete HP Designjet 8000s APS, net: approx. 60 kg
– Weight of the wooden pallet + 8000s APS + packaging: approx. 76 kg
– Weight of the complete HP Designjet 9000s/10000s APS, net: approx. 95 kg
– Weight of the wooden pallet + 9000s/10000s APS + packaging:approx. 113 kg
– The length of the forks must be at least: 1,000 mm
– The transport crates must be tightly fixed to the industrial truck in order to avoid
them falling over.
It is to be prevented that the APS and the hoisting platform of the industrial truck come into
contact:
– For this purpose wedge a distance wood or cardboard between the packaging of
the APS and the platform.
– Avoid hard knocks when setting down the APS.
– All persons must leave the working area of the industrial truck before lifting the APS.
10 User´s Guide
