Smeg KSET650X: INSTRUCTION ON MOUNTING AND USE GB

10

INSTRUCTION ON MOUNTING AND USE GB

Consult the designs in the front pages referenced in the text by

brackets using 4 screws (fig. 3).

alphabet letters. Closely follow the instructions set out in

2. Fix the air exit connector B above the cooker hood body

this manual. All responsibility, for any eventual inconveniences,

(fig. 3).

damages or fires caused by not complying with the instructions

Only for Filter Version:

in this manual, is declined.

place the deflector F on the exit connector.

Fix the filter holder frame inside the cooker hood, firstly

Description of the hood - Fig. 1

above on the rings R set in the body, then on the base

1 Control panel

using the two screws S (fig. 3).

2 Grease filter

3. Apply the supplied template first to the right and then to

3 Grease filter release handle

the left (fig. 4.1) or, if supplied, apply the apposite template

4 Halogen lamp

to the wall (fig. 4.2  only in case of models conceived

5 Vapour screen

for fixing to the wall) and making holes as indicated (for

6 Vapour screen guides

the templates for fixing to the wall units 3 dead holes are

indicated, 2 of Ø 2mm and one of Ø 5mm, while for the

7 Air exit

template for fixing to the wall, 2 holes of Ø 8mm).

8 Fairing (supplied in two sizes)

ATTENTION! TEMPLATE AND FIXING TO WALL

9 Fixing points for cabinet

UNIT

10 Inspection door for the suction group (ACCESS ALLOWED

The lower and back edge of the template must correspond

ONLY BY A QUALIFIED TECHNICIAN)

to the lower edge of the wall unit.

Installation - Fig. 5-6

ATTENTION! TEMPLATE AND FIXING TO WALL

The cooker hood must be placed at a minimum distance of

The lower edge of the template must correspond to the

43 cm from the cooking plane for electric cookers and 65cm

lower edge of the hood.

for gas or mixed cookers.

Only for models with fixing hooks: make the holes and

fix two hooks with screws and dowels

The hood is equipped with a top air outlet B for discharge

(J  fig. 4.2).

of fumes to the outside (Ducting version  exhaust pipe

Install the two supplied Y brackets with two screws and

and pipe fixing clamps not provided).

Where it is not possible to discharge cooking fumes and

washer each onto the upper side of the hood (fig.4.2).

vapours externally, the cooker hood may be used in the

4. Insert the body of the hood inside the wall unit (fig. 5).

filter version by mounting an active carbon filter and the

This can remain temporarily in position:

deflector F on the connection ring placed on the exit

a) in case of fixing to the wall unit, using lateral

perforation B (Fig. 3), the fumes and vapours are recycled

springs D to imbed into the Ø 5mm dead holes (to do this,

via the deflector.

press the lateral springs towards the inside of the body

The models with no suction motor only operate in ducting

mode, and must be connected to an external suction device

of the hood using a screwdriver as a liver.

(not supplied).

b) in case of fixing to the wall, with the hooks and the

brackets (the bracket have adjustable positioning screws).

Preliminary information for installation of the hood:

ATTENTION!

Disconnect the cooker hood from the electrical mains during

Check that the electric cable and the smoke outlet are

the electrical connection phase.

accessible to facilitate successive connections (and for

The cooker hood is designed for installation inside a wall

cabinet.

technical assistance and maintenance interventions).

It is recommended to install the cooker hood only inside a

5. Check that guides G (fig. 6) are perfectly parallel to the

cabinet of suitable dimensions.

lower edge of the wall unit, after which, ONLY in the case

Do not tile, grout or silicone this appliance to the wall. Surface

of fixing to the wall unit, definitely fix the body of the hood

mounting only.

to the sides of the wall unit with 4 screws (E  fig. 6 

Do not fix chimney flue to furniture or fly over shelves unless

the chimney flue can be easily removed, in case maintenance

two per side). The screws are to be inserted from

is ever required.

inside the body of the hood on the wall unit in

Refer to figure 2 for useful information for safe installation and

correspondence with the 4 Ø 2mm blind holes previously

for eventual perforations to perform at the base of the cabinet

made (see operation 3).

for air evacuation, for the

6. Insert the cooker hood cabinet base on the bracket guides

connection cable and to permit to access the electronic card

G then carry out the electrical connections of the cooker

that controls the cooker hood operation (ACCESS ALLOWED

ONLY BY QUALIFIED TECHNICIAN).

hood cabinet base to the casing (fig. 7).

Warning!

7. Regulate the cooker hood cabinet base in order that the

The cooker hood is supplied with 4 side spacers (2 for the

frontal part is in line with the cabinet (H - fig. 8) then block

right side and 2 for the left side), these are useful when the

the cooker hood cabinet base using 2 screws (one per

width of the housing cabinet for the cooker hood motor body

side - L - fig. 8  To insert these two screws you will

is wider than 6mm. In this instance the spacers should be

need to remove the filter grill and screw them on the

mounted outside the cooker hood body corresponding to the

perforations for the cabinet fixing screws (Fig. 2-A)

inserts that are fixed on the mantel guides).

8. Fix the cooker hood cabinet base to the cabinet using

1. Measure the cabinet depth (consider also the cabinet

the 2 screws M (fig. 8), use 2 of 4 perforations available

door) as for a depth of up to 315mm will require the

and check that the screws are fixed to the cabinet.

mounting of 37mm fairing, and for measurements over

9. Remount the grease filter, connect the cooker hood to the

315mm will require the mounting of 75mm fairing.

electrical network and to the discharge tube, check the

The fairing C should be fixed to the cooker hood body

perfect operation of the cooker hood.