Hoover XARION-XARION PRO TXP 1510 019: USER CHECKLIST

3

To access the exhaust filter:

1. Unlock the exhaust filter door by rotating the door along arrow indicated.

 [19]

2. Remove the filter pack from recess.

 [20]

3. Gently tap and wash the filter unit. Do not use hot water or detergents. Remove

excess water from the filter and leave to dry fully before reusing.

 [21]

4. Reassemble filter pack once fully dry and refit to the cleaner.

IMPORTANT:

 Do not use the product without the filter pack fitted. 

Cleaning the Airvolution separation unit

This cleaner uses the Airvolution separation system, unique to Hoover. If necessary the

Airvolution separation unit can be removed from the dust container and cleaned.

1. 

Remove dust container from the cleaner by releasing the container carry handle to 

detach the dust container from the main cleaner and pull upward to remove. 

[15]

2. 

Place the dust container on a flat surface and unclip the clips from either side of the 

dust container.

 [22]

3. 

Using the dust container handle lift the dust container upper section containing the-

separation unit from the lower section. 

[23]

4.  Use a cloth to remove excessive dust from the separation unit’s surface. 

[24]

5.  Reassemble the dust container upper section. Push clips back to fully close the dust 

container.

 [25]

6.  Refit the dust container to the cleaner. To lock in place push the container carry 

handle down until the latch connects with the main body of the cleaner. Once cor

-

rectly retained the carry handle will sit flush with the top of the cleaner.

Removing a blockage

1. 

Check if the dust container is full. If so refer to ‘Emptying the dust container.

2. 

If the dust container is empty but suction is still low:

A. 

Do the filters need cleaning? If so refer to ‘Cleaning the washable filters’.

B. 

Check if there is any other blockage in the system - Use a rod or pole to remove 

any blockage from the extension tube or flexible hose.

C. 

Check if pre-motor filter is fitted and filter door is closed

D. 

Check if the cyclonic unit needs to be cleaned. Refer to ‘Cleaning the cyclone 

unit’

USER CHECKLIST

Should you have a problem with the product, complete this simple user checklist

before calling your local Hoover service.

•  Is  there  a  working  electricity  supply  to  the  cleaner?  Please  check  with  another 

electrical appliance.

•   Is the cyclonic dust container over-filled? Please refer to ‘Cleaner Maintenance’.

•  Is the filter blocked? Please refer to ‘Cleaner Maintenance’.

•   Is  the  hose  or  nozzle  blocked?  Please  refer  to  ‘Removing  a  blockage  from  the 

system’.

•  Has the cleaner overheated? If so, it will take approximately 30 minutes to auto

-

matically reset.

IMPORTANT INFORMATION

Hoover spares and Consumables

Always  replace  parts  with  genuine  Hoover  spares.  These  are  available  from  your  lo

-

cal Hoover dealer or direct from Hoover. When ordering parts always quote your model 

number.

Consumables:

• Hepa Pre-Motor Filter: S104 - 35600990

• Hepa Exhaust Filter Door: T101 - 35600991

Hoover Service

Should you require service, spares and consumables at any time, please contact your 

local Hoover Service Office.

Quality

BSI ISO 9001

Hoover’s factories have been independently assessed for quality. Our products are   

made using a quality system which meets the requirements of ISO 9001

GB

(*Certain Models Only)

4800xxxx Xarion Pro Standard handle ML ef.indd   3

25/01/2011   10:36:28