Babyliss 889AE: ENGLISH

3. Turn the tube connector (7) in

ENGLISH

a anti-clockwise direction to

loosen it and release the

BABYLISS GENERAL

upper tube (6). Pull out the

INSTRUCTIONS

upper tube to the desired

The BaByliss Super Hood Dryer

length. Tighten tube

is protected in its pack and

connector to secure.

stable once erected, but care

4. Fix the drying hood onto the

should be taken during

top of the aluminium upper

assembly.

tube (6), at position (8)

making sure that the hole in

NB:

the side of the hood socket is

Never lift the hood by the visor.

aligned with the equivalent

The position of the hood is fixed

hole in the aluminium upper

to give optimum comfort in use.

tube. Insert the 12mm screw

Do not attempt to adjust the

(provided) into the aligned

angle.

holes and tighten. NB: for

optimum stability, always

ASSEMBLY INSTRUCTIONS

ensure that the drying hood is

The BaByliss Super Hood

positioned directly over the

requires careful assembly

non-weighted foot (1) of the

before use. Please read the

base.

following Assembly instructions

5. Snap the plastic lead bracket

carefully:

(9) onto the aluminium upper

tube (6) to hold the lead in

1. Slide the non-weighted foot

position. Then slide the lead

into the extended base

under hook located on top of

socket (1) until it clicks home.

base socket (3) (11).

Insert the 30mm screw

6. The removable filter must

(provided) into hole under

always be in position on the

base and tighten to secure

top of the hood before using

foot. Slide the 3 weighted

the dryer.

feet into the remaining base

sockets (2), (3), (4).

USE INSTRUCTION

2. Push the plastic lower tube

• Adjust the height of the hood

(5) into the top of the base

to suit your sitting position, via

segment (10) as far as it will

the tube connector, sliding the

go, ensuring that the slot in

aluminium upper tube up or

the lower tube slides over the

down as necessary before

ridge inside the base

re-locking.

segment.

• The front visor should be

pushed upwards until it clicks

5

into a holding position.

position.

• Select one of the 3 heat levels

NB: Always ensure that the

using switch located on the

dryer is switched to the off

side of the hood.

position (using the side

switch) after each use.

Position III:

For rapid drying or starting the

CLEANING

drying process or for thick/long

Use only a soft, damp cloth with

hair

mild detergent and always

Position II:

ensure that the dryer is fully dry

For normal drying

before use.

Position I:

Cool setting for finishing the

CAUTION

style

• Do not immerse in water or

other liquids and do not use

Start with III or II and end with I

near basins or other vessels

containing water.

1. Prepare your hair for drying in

• Unplug the hairdryer after use

your usual way e.g. in rollers,

since the proximity of water

lightly towel dried, etc.

can be dangerous even if it is

2. lift up the visor. Plug in and

switched off. For additional

switch to Position I or II or III.

protection the installation of a

3. Make yourself comfortable

residual current device (RCD)

under the hood dryer. Pull

with a rated residual operating

down the front visor: this will

current not exceeding 30 mA

automatically switch the

is advisable in the

dryer on.

electrical circuit supplying the

4. Some styles require a greater

bathroom. Ask your installer

airflow on the top of the

for advice.

head, whilst others (e.g. long

• Store out of children’s reach.

hair) require the airflow to be

• Always unplug the appliance

directed around the sides. To

when not in use . Do not leave

give this flexibility, the Super

unattended when switched

Hood Dryer is fitted with an

on.

adjustable diffuser. To

• Take care to avoid contact

operate this, there is a

between the hot surfaces of

slide-switch situated on the

the appliance and the face or

inside front edge, underneath

neck.

the hood.

• Always ensure the voltage to

5. When you want to stop the

be used corresponds to the

dryer, simply lift the front

voltage on the unit.

visor until it is held in

• Do not wrap the supply cord

6

around the appliance.

minutes but please check

• Do not use the appliance if

removable filter is clean before

the cord is damaged. In the

continuing to use the dryer.

event of damage discontinue

use immediately. If the

supply cord is damaged, it

Discarding electrical

must be replaced by the

and electronic equip-

ment at the end of life.

manufacturer or its service

In everybody's interest

agent or a similarly qualified

and to participate active-

person in order to avoid a

ly in protecting the environment:

hazard.

• Do not discard these items

• Return the appliance to the

with your household waste.

nearest service facility for

• Use the available trade-in and

examination, electrical or

collection systems.

mechanical adjustment or

Some materials can in this way

repair. No repair should be

be recycled or recovered.

attempted by the consumer.

• Allow to cool before storing

away.

• Remember to clean the

removable filter regularly. To

remove the filter, pull the lock

at the back of the filter and

pull it.

• Always ensure that the dryer

is switched to the off position

after each use.

• This appliance complies with

the requirements of Directives

89/336/E.E.C.(Electromagneti

c compatibility) and

73/23/E.E.C. (Safety of

domestic appliances),

amended by Directive 93/68/

E.E.C. (C.E. marking).

NB:

The BaByliss Super Hood Dryer

has a safety cut-out which will

operate in case of overheating.

The dryer will re-set itself after

being left to cool for a few

7