LED LENSER H7R.2: LED LENSER® * H7R.2

LED LENSER® * H7R.2

is preferrable when a high brightness level is

c) Light Mode three - Signal: when the product

more important than a long burn time

is off, firmly press the front switch until it

blinks thrice. The white LED will glows with full

6.3 Changing the Energy Modes

brightness (light function: Power). A second

Changing the Energy Modes can only be done

touch to the button on top of the lamp will start

when the flashlight is in Light Program White

the strobe (12 Hz) (light function: Pulse), and a

and the lamp is turned Off. To change the

third touch will turn the lamp off.

energy mode, with the white LED off, press the

“Multi-function Wheel” on the back 8 times,

Note: In the low power- and power- function,

then on the 8th click keep the knob pressed

you can adjust the brightness stepless by

for approx. 2-4 seconds. This should allow

turning the multi-function "Wheel" switch (Dim

you change between the “energy mode“ and

function). A short flash indicates the darkest (5

“constant current mode.“ You know which

lumens) or brightest setting.

mode you are in when:

In the Pulse- function, you can speed up or

slow down the flashing frequency by turning

a) Constant current mode: the brightness

the multi-function "Wheel" switch (Pulse

reduces immediately in 2 seconds.

function).

b) Energy saving mode: the brightness reduce

d) Boost Mode: in each setting, press the front

gradually to zero.

switch for 2 seconds, you will enter to boost

mode, after a short time the flashlight will

With this procedure, you can switch between

return to previous choosing.

the two Energy Modes. It is not possible to

The Light Functions above are in a loop.

determine in which Energy Mode the H7R.2

Note: when switching between modes, press

is. To find this out, you must carry out the

the “Multi-function Wheel” switch button no

procedure. If the H7R.2 is thereafter not in

longer than 2 seconds, otherwise the product

the desired Energy Mode any more, you must

will turn off.

repeat the procedure again. The flashlight will

reset to energy saving mode if you change the

5.2 Light Program Red (rear light)

battery or cut the power.

ON-OFF / transition mode (change modes

within 2 seconds, but more than 2 seconds the

7. “Transport Lock”

lamp will turn off) / charge indicator/ battery

When the H7R.2 switched Off, press the front

capacity indicator function is available for the

switch for approx. 5 seconds till the light turns

red LED:

off in order to enable the “Transport Lock.” The

H7R.2 cannot be turned on any more, either

1) ON-OFF function: in any status, two red LED

intentionally or unintentionally. Accidental

will light up by pressing the “Multi-function

power consumption is not possible.

Wheel” switch once: the LEDs will start to blink,

To deactivate the “Transport Lock”, just press

by pressing the switch twice; at the third push

the front switch again for 5 seconds. The

the LEDs will turn OFF.

headlamp will now return to the Light Program.

2) Charge indicator function: the red LED will

8. Reset function

glow when charging. After full charge, the LED

If the Accumulator-Pack & the alkaline

will glow green. Note that the white LED will

batteries are taken out the battery box you

not work when charging.

have "reset" the H7R.2. You have thus reset a

few functions:

3) Battery capacity indicator: when you start

The Light Program White (see Section 5.1) is

to use white LED, the red LED on the battery

activated

box will glow for 5 seconds and then turn off.

The Light Function Dim (see Section 5.1) is set

Green means that the battery capacity is at

to low brightness

50%-100%; yellow means the battery capacity

As Energy Mode Energy Saving is activated (see

is at 20-49%; when the red LED is glowing the

Section 6).

battery capacity is lower than 19% & not suit

The “Transport Lock“ (see Section 7) is

for long time use, therefore must be charged.

deactivated

6. Energy Modes

9. Charging

By selecting one of the two Energy Modes

The H7R.2 indicates by the flashing white LED

(Energy Saving or Constant Current), you

that it is running out of energy in near future.

decide how the energy contained in the

Please charge the Accumulator-pack in time.

accumulator or batteries are used.

Charge the Accumulator-pack of your H7R.2 in

a dry place and only by using the charger that

6.1 Energy Saving: The light output is

is included in the delivery or by a USB port (see

controlled by the integrated Smart Light

below).

Technology (SLT). The brightness is adjusted

The following information applies only to the

to the realistic conditions that occur during

included accessories. You cannot charge any

normal use of the lamp, thus providing a longer

other accumulators or batteries in the H7R.2.

burn time.

In the scope of delivery of the H7R.2 there

is a plug and a charger. In case both are not

6.2 Constant Current: This Energy Mode allows

connected already, please connect them so

the continuous use of all the Light Functions

that the connection clicks.

with a constant light output. This Energy Mode

H7R.2 charger has a USB port which must be

03

GB

connected with the corresponding port at the

sound. Then push the middle of the cover

supplied charging cable in order to charge

again, until you hear another “click”. Now the

the Accumulator-pack. The other side of the

battery cover is securely closed.

charging cable (micro USB) must be connected

to the micro USB port on the battery box.Only

11. Headband

the supplied Accumulator battery pack can be

The headband can be washed by water. The

charged with the charger.

headband can be washed in a washing machine

The last step is to connect the plug into a

at 30 °C.

socket (Input: 100 V to 240 V / 50 Hz to 60 Hz).

When charging is completed (after maximum 4

12. Cleaning

to 5 hours), unplug the charger from the socket

To clean, use a dry, lint-free, clean cloth.

and the charging cable (micro-USB) from the

If salt water is spilled on the head lamp, it must

Accumulator-pack. It is, however, no problem

be immediately entirely removed with such a

to continue charging the Accumulator-pack

cloth and water.

even it is already full.

When you are charging the Accumulator-Pack

13. Scope of delivery

of the H7R.2 with the corresponding charger

The H7R.2 headlamp is supplied with the

and charging cable by a USB port (see Section

following accessories:

9) the charging status will be shown by a

1 H7R.2 headband

glowing LED light. When the battery is still

1 charger and plug

charging, it will shine red. The light will change

1 USB cable, connect the rechargeable battery

to green when the charging is completed. You

and charger for charge

will be unable to use the white LED of H7R.2

1 battery pack

while charging.

1 user manual

Instead of connecting the charging cable to the

USB port of the charger, you can also connect

14. General information batteries /

it to a different USB port (5 V / 500 mA) such as

accumulators

a computer.

Non rechargeable batteries or other

While using our optionally available car USB

accumulators that are not of the same type

charger connection (Led Lenser Car Charger:

of accumulator as the one included in with

Item no. 0380), the H7R.2 also can be charged

this product and therefore not allowed to be

at the cigarette lighter and sockets in vehicles.

charged by the same charger. Never use non

These accessory units match themselves

rechargeable batteries and accumulators

automatically to the respective input voltage

together. Always change all nonrechargeable

(12 V ó 24 V). These alternatives are suitable to

batteries and accumulators at the same time.

charge the Accumulator-pack in case a power

Only use the Accumulator-Pack (scope of

outlet is not available.

delivery), alkaline batteries AAA / LR03 / Micro

Note – Please ensure that there is no short-

(1.5 V DC) or NiMH-Accumulator AAA / LR03 /

circuit at the charging contacts. The charging

Micro (1.2 V DC) for the H7R.2.

contacts may not be touched with moist or

metallic objects.

If you intend not to use the item for an extended

period, please take out the Accumulator-Pack,

10. Changing of the Accumulator-Pack / NiMH-

NiMH-Accumulators or alkaline batteries in

rechargeable batteries / Alkaline batteries

order to avoid damage.

Prior to the changing batteries, please turn off

the H7R.2.

Used batteries and accumulators have to

On the back of the battery box, where the

be taken out the item and disposed of in

headband is attatched, there is the gate to the

accordance with the national laws. The

inside of the battery box. Once you open the

possibility of short-circuits of accumulators

battery box, there will be a silk tab that runs

and batteries must be eliminated and so they

underneth the battery pack. In order to remove

may not be opened, thrown into a fire, or enter

the battery, pull the silk tab and then insert a

into the human body in any way.

new one.

Alkaline batteries can also be inserted, but

Do not swallow any small parts or batteries/

then the charger cannot be used!

accumulators that are present. The products

During insertion, it is always necessary that

or parts thereof (including batteries /

it is in the correct direction. Therefore, pay

accumulators) must be stored out of the reach

attention to the polarities (+ and -). Both in the

of children.

battery box and also on the Accumulator-Pack

/ alkaline batteries. Otherwise, there is risk

For safety and approval reasons (CE), the

for damaged Accumulators / batteries and a

product must not be modified and/or changed.

possible explosion.

The product is to be used exclusively as an

The supplied Accumulator-Pack can only be

accumulator or battery powered lamp. If

recharged with the original charger or by a

the H7R.2 is used for any other purpose, or

USB port (see Section 9)!

incorrectly, it can get damaged and a hazard-

After replacing the batteries, the cover of the

free use is no longer guaranteed (danger from

battery box has to be closed again.

fire, short-circuit, electric shock etc.) and

To close the battery box, hold the battery box

therefore there will be no liability for harm

cover over the battery box in the right direction,

anyone or damage to property. The warranty

hook the battery cover above the multi-function

of the manufacturer is also rendered null and

switch and then push the battery cover against

void.

battery box, until you hear a small “click”

04