Elta 9050N5: GB GB

• Loosen the set screw (17). Please note that the hexagon nut (18) is

• Place and screw the adjusting screw cap onto the stand tube. Pull out

• Unscrew the adjusting screw cap (19) from the stand tube counter

• Place the stand tube on the base plate and tighten it with the four

• To pull out the telescope tube from the stand tube casing, simply push

• Remove the screws from both parts of the base plate and place them

• Clean the device as described below under

• Remove all packaging material.

• The device is intended for private use and fanning only. The device is

• Do not plug the device into the socket before it is not mounted

• Keep the device away from lose objects such as plants, curtains, etc.

• Do not operate the device in a horizontal position or without a base.

• Unplug the device before cleaning or demounting it.

• Do not operate the device in an extremely hot or moisten environment

• Infants, children and elderly persons should not be exposed to the cold

• Do not put your fingers or any other objects in the protection basket

• The protection basket must be closed properly when operating the

• Children should be supervised to ensure that they do not play with the

GB

GB

MOUNTING

BEFORE FIRST USE

INTENDED USE

SPECIAL SAFETY INSTRUCTIONS

mounted on the inside. Turn the set screw until the upper part of the

tighten the screw cap.

the telescope tube until you have reach the desired extent, then

plate and the stand tube.

clockwise and slide the cover (20) on the junction between the base

screws.

wooden stick.

telescope tube is retracted. Use an auxiliary object such as a blunt

the telescope tube from the bottom of the stand tube casing if the

crosswise on each other.

Maintenance.

not intended for commercial or industrial use.

completely.

(e.g. bathroom).

air stream over a long period of time.

operation.

during operation. Do not remove the protection basket during

device.

appliance.

concerning use of the appliance by a person responsible for their safety.

Dry all parts carefully before using the device.

Cleaning and

9 10

• The bend of the ventilator head can be adjusted. Turn off the

• To let the ventilator head constantly oscillated from left to right, push

• Select your desired fanning speed by turning the switch in the 0 / 1 / 2

• Plug the power plug (23) into a suitable socket.

• The mounting is finished and the stand ventilator is ready to operate.

• Insert the screw (2) into the bore holes of the protection baskets and

• Put the front protection basket into position so that the bores on the

• Place the front protection basket (1) in to the basket hook (8) and

• Tighten the rotor by turning the clamping knurled-head screw (3) on

• Slide the rotor (4) on to the rotor shaft (11). The mounting on the rotor

• Screw the clamping ring clockwise into the screw thread so that the

• Turn the clamping ring (5) at the rear of the rotor shaft counter

• Turn the clamping knurled-head screw (3) at the front of the rotor shaft

GB

GB

OPERATION

desired position. Tighten the knurled-head screw.

handle (10) of the protection basket and tilt the ventilator head to the

the knurled-head screw (15) from the vertical joint (14). Take the

oscillation switch beforehand by pulling the switch upwards. Remove

desired position is reached.

concentrated place, simply pull the oscillation switch upwards until the

the oscillation switch downwards (13). To direct the air stream on a

3 = high speed

2 = medium speed

1 = low speed

0 = device is off.

/ 3 (16) position.

on the protection basket.

secure it with the proper hexagon nut (9). Close all open holding clips

Therefore loosen the holding clips a little bit.

upper part of the protection baskets are on top of each other.

close the four holding clips (6) at the rear protection basket.

the rotor shaft counter clockwise to the position “TIGHTEN”.

shaft must be placed on the designated opening of the rotor.

rear protection basket fits tightly to the motor casing.

casing.

the protection basket’s metal ring must lay on the cam of the motor

holes and handle line up properly. The round opening on the inside of

protection basket (7) on the motor casing and make sure that the

clockwise and remove it from the motor casing (12). Place the rear

(11) clockwise to the position “Loosen” and remove it.

the device on the telescope tube and tighten the set screw.

device can be placed on the telescope tube. Place the upper part of