GBC H425: instruction

™

HeatSeal

H425

G

Instruction Manual

F

Manuel d’utilisation

D

Bedienungsanleitung

I

Manuale d’istruzioni

O

Gebruiksaanwijzing

E

Manual de instrucciones

P

Manual de Instruções

T

Kullanım Kılavuzu

K

Οδηγίες

c

Brugsvejledning

o

FI

Käyttöopas

o

NO

Bruksanvisning

S

Bruksanvisning

Q

Instrukcja obsługi

o

CZ

Návod k obsluze

H

Használati útmutató

RUS

o

Руководствo по

зкcплyатации

English 4

Français 6

Deutsch 8

Italiano 10

Nederlands 12

Español 14

Português 16

Türkçe 18

Ελληνικά 20

Dansk 22

Suomi 24

Norsk 26

Svenska 28

Polski 30

Česky 32

Magyar 34

Pyccкий 36

2

1

3

5

4

4

Specifications

GBC HeatSeal H425

Electrical

230V / 50Hz / 3.5A / 750W

Machine Dimensions

550 x 170 x 140mm

Machine Weight

5.5kg

Maximum Pouch Width

320mm

Minimum/Maximum Pouch Thickness

2 x 75 mic (Total 150) / 2 x 250 mic (Total 500)

Maximum Thru-put Thickness

1mm

Warm-Up Time (2 x 75 mic)

3-5 minutes

Speed

400mm per minute

Safety instructions

m

Important safeguards

m

YOUR SAFETY AS WELL AS THE SAFETY OF OTHERS IS IMPORTANT

WARNING: FOR YOUR PROTECTION DO NOT CONNECT

TO ACCO BRANDS EUROPE. IN THIS INSTRUCTION MANUAL AND ON

m

THE POUCH LAMINATOR TO ELECTRICAL POWER UNTIL

THE PRODUCT ARE IMPORTANT SAFETY MESSAGES. READ THESE

YOU READ THESE INSTRUCTIONS COMPLETELY. KEEP

MESSAGES CAREFULLY.

THESE INSTRUCTIONS IN A CONVENIENT LOCATION FOR

FUTURE REFERENCE. TO GUARD AGAINST INJURY, THE

THE SAFETY ALERT SYMBOL PRECEDES EACH SAFETY

FOLLOWING BASIC SAFETY PRECAUTIONS MUST BE

m

MESSAGE IN THIS INSTRUCTION MANUAL.

OBSERVED IN THE SET-UP AND USE OF THIS PRODUCT.

THIS SYMBOL INDICATES A POTENTIAL PERSONAL

SAFETY HAZARD THAT COULD HURT YOU OR OTHERS,

AS WELL AS CAUSE PRODUCT DAMAGE OR PROPERTY

General safeguards

DAMAGE.

• Use the unit only for its intended purposes of laminating documents.

THIS WARNING IS FOUND ON THE PRODUCT.

• Do not place anything in the throat opening of the laminator other than

pouches/documents.

m

WARNING

• Place unit on a secure, stable work area to prevent the unit from

c

Electrical shock hazard.

falling and possibly causing personal injury and damage to the unit.

Do not open. No user

• Follow all warnings and instructions marked on the unit.

servicable parts inside.

• The socket outlet shall be installed near the equipment and shall be

Refer servicing to qualified

easily accessible.

service personnel.

• Do not attempt single side lamination, this will destroy the laminator.

This safety message means that you could be seriously hurt or killed if

• Do not block the vent slots, this will cause the laminator to overheat.

you open the product and expose yourself to hazardous voltage.

Electrical safeguards

Special notice

• The unit must be connected to a supply voltage corresponding to the

Thank you, for your recent purchase of a GBC Pouch Laminator. Your

electrical rating shown on the unit.

new laminator may emit a slight odour during the initial stage of

operation. It is normal and will diminish after several hours of operation.

• Unplug the unit before moving it, or when it is not in use for an

extended period of time.

• Do not operate with a damaged supply cord or plug. Do not alter the

Cleaning

attachment plug. The plug is configured for the appropriate electrical

supply.

Caution: Unplug this product before cleaning.

• Do not overload electrical outlets beyond their capacity; fire or

m

• Wipe exterior only with a damp cloth. Do not use detergents

electrical shock could result.

or solvents.

• The unit is intended for indoor use only.

• Do not use aerosol dusters or cleaners

• Do not spill liquid of any kind on this product.

• Do not spray anything into the product, foreign substances

• Close supervision is required when this product is used near children.

can be explosive.

Service

• Do not attempt to service or repair the pouch laminator yourself.

Unplug the unit and contact an authorised ACCO Brands Europe

service representative for any required repairs.

4

G

Operation, hot lamination

Reverse feature

1

Connect the power cord plug to the appropriate power source.

In the event of a misfeed or a jam follow these instructions.

2

Push the power button to “ON” position. The red power indicator will

1

Press the reverse button and hold down (fig.5). This will reverse

illuminate (fig.1).

the rotation of the rollers allowing the pouch to exit the front of the

machine.

3

Using the lamination guide located on the machine (fig.1), select the

appropriate temperature setting for the pouch gauge thickness and

2

Pull the document out of the laminator.

material you are laminating using the rotary knob control.

3

After the document is out of the machine clean the rollers by

Temperature Setting Guidelines

running the cleaning sheet through the laminator.

When laminating thin paper with light ink coverage, set the temperature

dial to the low end of the film gauge range. Thick paper with heavy ink

Caution: Use caution when removing the laminated pouch

coverage requires higher settings within the range. Temperature settings

m

from the machine. It may be hot.

will vary due to the finish, chemistry, and heat absorption properties

of the material being laminated. If the laminated pouch is cloudy after

the first pass through the machine, adjust the temperature to the next

higher position and run it through again. If waviness occurs, reduce the

Note

temperature to the next lower position. Always allow sufficient time for

1

Never insert the loose end of the pouch first into the machine. This

the laminator temperature to adjust to the changes made to the settings.

could cause the machine to jam.

4

When the laminator has reached the correct lamination temperature

2

Never attempt to do single sided lamination. This will cause the

the green (ready) light will illuminate.

machine to jam.

5

Centre the item to be laminated within the pouch left to right with

3

After laminating run a clean card through the machine to clean glue

the top edge against the sealed edge of the pouch (fig.2).

residue off of the rollers. This will extend the life of the rollers.

6

Insert the pouch with the sealed edge first into the machine (fig.3).

7

The laminated item will automatically exit at the rear of the machine.

After the pouch has stopped moving, carefully remove from the

machine and place on a cool flat surface for approximately one

minute for cooling (fig.4).

8

If you are finished laminating push the power switch to turn the

machine off.

Operation, cold lamination

1

Connect the power cord plug to the appropriate power source.

2

Push the power button to “ON” position. The red power indicator will

illuminate (fig.1).

3

Rotate the temperature dial to position.

4

Follow the instructions included with your GBC self adhesive

laminate or other pressure sensitive, non thermal laminating

pouches.

Guarantee

Operation of this machine is guaranteed for two years from date of

persons not authorised by ACCO Brands Europe will invalidate the

purchase, subject to normal use. Within the guarantee period, ACCO

guarantee. It is our aim to ensure that our products perform to the

Brands Europe will at its own discretion either repair or replace the

specifications stated. This guarantee does not affect the legal rights

defective machine free of charge. Defects due to misuse or use for

which consumers have under applicable national legislation governing

inappropriate purposes are not covered under the guarantee. Proof

the sale of goods.

of date of purchase will be required. Repairs or alterations made by

Register this product online at www.accoeurope.com

5