Hoover MISTRAL TMI2017 019: clEANER MAINTENANcE

clEANER MAINTENANcE

Emptying the dust Container

when  the  dust  reaches  the  max  level  indicator  on  the  container,  empty  the  dust 

container.

important:

 To maintain optimum performance do not allow the dust to sit higher than 

the max level.

Remove the hose from the cleaner. 

1. 

[2]

Press the dust container release buttons on the bin cover 

2. 

[18]

 and lift the dust container 

out of cleaner. 

[19]

USING yOUR clEANER PARKING AND STORAGE

Hold  the  dust  container  upside  down  so  that  the  pre-motor  filter  faces  upwards. 

3. 

Unlatch then unhinge the pre-motor filter frame and remove the pre-motor filter from 

the frame. 

[21]

 If the filters are dirty refer to section ‘cleaning the washable filters.

Hold the dust container over a bin, press dust container flap release button to empty 

4. 

the dust. 

[23]

Use the dusting brush 

5. 

[1S]

 when necessary to remove excessive dust from the internal 

surface of the dust bin.

close  the  dust  container  flap  and  relocate  the  pre-motor  filter  frame  on  top  of  it, 

6. 

ensuring the latch is well closed. Then refit the dust container into the cleaner.

Cleaning the Washable Filters

The cleaner is fitted with a pre-motor filter. To maintain optimum cleaning performance, 

regularly  clean  the  filters.  Remove  excess  dust  from  the  filters  by  gently  tapping  them 

against the side of a bin. The filters should be washed after every 5 container empties.

important: all bagless cleaners require regular filter cleaning. Failure to clean your 

filters may result in air blockage, overheating and product failure. this may invalidate 

your guarantee.

important:  regularly  check  and  maintain  the  filters  by  following  the  filter 

maintenance instructions , it is also recommended that you purchase new filters after 

every 3rd filter wash. this will maintain your cleaners performance.

to access the pre-motor filter:

Remove the Dust container from the cleaner mainbody. 

1. 

[19]

Hold  the  Dust  container  over  a  bin  with  one  hand,  Hold  the  dust  container  upside 

2. 

down so that the pre-motor filter faces upwards. Unlatch then unhinge the pre-motor 

filter frame and remove the pre-motor filter from the frame. 

[21]

Gently tap and wash the filter packs using hand warm water. 

3. 

[22]

 Remove excess water 

from the filters with a dry cloth and leave to dry fully before re-using.

Reassemble filter packs once fully dry and refit to the cleane.

4. 

important:

 Do not use the product without the pre-motor filter pack fitted.

important:

 Always ensure the filter packs are fully dry before use.

to access the exhaust filter:

Unlock the exhaust filter cover by sliding the button towards the rear of the cleaner.

1. 

Remove the filter pack from the recess. 

2. 

[20]

Gently tap and wash the filter pack using hand warm water. 

3. 

[22]

 Remove excess water 

from the filters with a dry cloth and leave to dry fully before re-using. Reassemble filter 

packs once fully dry and refit to the cleaner.

remember: 

Do  not  use  hot  water  or  detergents.  In  the  unlikely  event  of  the  filters 

becoming  damaged,  fit  a  Genuine  Hoover  consumable.  Do  not  try  and  use  the  product 

without a filter fitted.

2

*Certain models only

** nozzle design may vary according to model

gB

Extract power cord and plug it into the power supply. 

1. 

[5] 

Do not pull the cord beyond 

the red marker.

Adjust the telescopic tube to the desired height by moving the telescopic tube adjusters 

2. 

up and raise and lower the handle to the most comfortable cleaning position. 

[6]

carpet & floor Nozzle** - Press the floor type selector pedal on the nozzle 

3. 

[7]

 to select 

the ideal cleaning mode for the floor type.

hard Floor:

 brushes are lowered to protect the floor.

Carpet:

 brushes are raised for the deepest clean.

Switch the cleaner on by turning the On - Off / Variable Power control Roller clockwise 

4. 

on the cleaner main body. 

[8]

Adjust  the  power  level  by  turning  the  On-Off  / Variable  Power  control  Roller  to  the 

5. 

desired level. 

[8]

Switch  off  at  the  end  of  use  turning  the  On-Off  /  Variable  Power  control  Roller. 

6. 

[8]

Unplug and gently pull the cord, the cord will begin to automatically retract back into 

the cleaner. 

[9]

The flexible hose and tube can be parked for temporary storage while in use 

[10]

 or in the 

Nanopack storage position when not in use 

[17]

:

Retract the telescopic tube to its storage length.

1. 

Remove the nozzle from the end of the telescopic tube. 

2. 

[11]

Remove the hose handle from the telescopic tube. 

3. 

[12]

lift the hose latch at the rear of the cleaner [13] and wrap the flexible hose around the 

4. 

product. 

[14]

Park the hose handle on the product. 

5. 

[15]

Assemble the nozzle into the parking slot underneath the product. 

6. 

[16]

Assemble the telescopic tube into the remaining parking slot underneath the product. 

7. 

[17]

MistralManual__1-4_union.indd   2

01/07/2011   17.54.44