Zelmer 619: CLEANING CARPETS
CLEANING CARPETS: Zelmer 619
Table of contents
- 57
- 61
- IMPORTANT SAFETY INSTRUCTIONS TECHNICAL DATA
- 85
- 86
- A – FOR VACUUMING WITH PAPER BAG WITHOUT WATER. B – FOR VACUUMING WITH PAPER BAG WITH 1.5 L OF WATER AS ADDITIONAL FILTER. C – FOR VACUUMING WITHOUT PAPER BAG, DIRECTLY TO THE FILTER CUP USING “FIZELINA” FILTRATION PAD, OR WITHOUT IT.
- ATTENTION!!! In case of difficulties in a/m elements connection lubricate the sealing with i.e. ATTENTION!!! Be careful during pulling the cord out, the yellow mark on the ATTENTION!!! The vacuum cleaner is equipped with a float, which shall In such situation: ATTENTION!!! The float can also operate during sudden movements, sharp pulling, hitting, or crossing the doorsteps.
- 89
- CLEANING CARPETS
- PLAIN FLOORS CLEANING AFTER OPERATION
- FILTERS REPLACEMENT ECOLOGY
0
90
−
Pour dirty water out including the dirtiness form the tank and rinse the tank.
−
Insert the water filter without paper bag and filtration pad.
−
Place the tank at the base and close the top lid.
−
Remove the nozzle or the brush, which was used earlier
and fit the nozzle for wet clearing on the sucking tube.
−
Remove the back tank:
−
open the top lid and bring it to vertical position 1.
−
move the tank up and then move it back 2.
−
Remove the inlet pin and fill the tank up with cleaning agents
(the powder solution or liquid), according to the label:
1. Powder, cleaning solution preparation: dissolve the content
of the bag in 2,5 – 3l of warm water- temp. up to 45ºC.
2. Cleaning liquid: pour the measured portion of the liquid into
the back tank. 1 pin of liquid for 3,5l water.
−
Depending on the applied clearing agent, fill the back tank up with prepared solution or warm water
with temp. up to 45ºC.
−
Insert the pin into the inlet in back tank.
ZELMER S.A. warranties good cleaning effect and proper vacuum cleaner operation, only using the
cleaning agents and their amount approved by ZELMER S.A., which is indicated at the label:
−
„DYWANOPUC” cleaning powder manufactured by OKTIMA,Poland,
−
„CARPEX” cleaning liquid manufactured by ASTRA POLLENA, Poland,
−
„FOUNTAINHEAD” cleaning liquid manufactured by Butcher’s, USA
−
Place the tank in previous place and push it in to fasten it exactly at the vacuum
cleaner housing.
−
Close the top lid.
ATTENTION !!! The vacuum cleaner is equipped by the manufacturer with one
of the a/m cleaning agents only.
CLEANING CARPETS
heck the colours resistance before wet cleaning.
Put a small amount of cleaning agent on white cloth (powder solution or liquid) and clean the carpet in
the least visible place. If the cloth will be coloured, it means that the carpet does not have permanent
colours and can not be cleaned this way.
To protect against foam generation, or when it is generated during cleaning, use the anti-
foaming agent recommended by ZELMER S.A., in amount and way explained at the label
:
−
“ANTYPIENIACZ III” provided by OKTIMA Poland,
−
„FOAM-FREE” provided by Butcher’s, US .
ATTENTION!!! The vacuum cleaner is equipped by the manufacturer with one
of the a/m cleaning agents only.
−
Remove the brush strip from the nozzle
−
Check the right direction of nozzle movement on the carpet, so that it has the least
friction.
−
Press the pump on/off button in and switch
the vacuum cleaner on.
ATTENTION!!! You can switch the pump on only, when there is water
inside the back tank. The lack of water is indicated with very noisy pump operation.
−
Press the adjusting button at the hose handle to adjust the water flow to the nozzle.
−
Move the nozzle along the carpet with forward and backward movements.
