Zigmund & Shtain CNS 119.60 BX: ENGLISH

ENGLISH: Zigmund & Shtain CNS 119.60 BX

GB

ENGLISH

exceed 60°C. Failure to respect this precaution may determine

GENERAL

improper functioning of the TOUCHCONTROL system.

Carefully read the contents of this lea et since it provides

Positioning (Fig.1)

important instructions regarding safety of installation, use

The domestic appliance is designed to be built into a worktop

and maintenance.

as illustrated in the speci c  gure. Apply sealant around the

Keep the leaflet for possible future consultation. All the

entire perimeter (cut-out dimensions Fig.1B). Fix the domes-

operations relating to installation/replacement (electrical

tic appliance on the worktop by means of the 4 brackets

connections) must be carried out by specialised personnel

provided, taking the thickness of the worktop into account

in conformity with the regulations in force.

(Fig.1A). If the lower part of the appliance, after installation, is

accessible via the lower part of the cabinet then it is necessary

SAFETY WARNINGS

to mount a separator panel respecting the distances indicated

(Fig.1C). If the appliance is installed with an oven underneath

It is recommended to use  at-bottom pans with a diameter

then the separator is not necessary.

equal to or slightly larger than that of the heated area. Do not

use pans with a rough base to prevent scratching the heat

Electrical connections

surface of the cooktop (Fig.2).

Before making the electrical connections, check that:

This appliance is not suitable for use by children or persons

- the ground cable is 2 cm longer than the other cables;

requiring supervision. Do not let children play with the ap-

- the system ratings meet the ratings indicated on the

pliance.

identi cation plate  xed on the lower part of the worktop;

- the system is  tted with e cient earthing compliant to

Important

the laws and regulations in force.

- Avoid spilling liquid, therefore to boil or heat liquids, reduce

Earthing is obligatory by law.

the heat.

If the appliance is not  tted with a cable, use type:

- Do not leave the heating elements on with empty pots and

"H05V2V2-F" for a power level of up to 6400 Watts. The cross-

pans or without receptacles.

section of the cable should be at least 2.5 mm, or 4 mm for

- When you have  nished cooking, switch o the relevant

greater power levels.

heating element with the control indicated below.

The cable should never reach a temperature which is 50°C

above the temperature of the room in which it is installed.

Attention:

The appliance is designed for permanent connection to the

- Steam cleaners must not be used.

electricity supply and should therefore be fitted with an

- If the surface is cracked, switch o the appliance to

omnipolar switch which has a minimum opening of 3 mm

prevent electric shock.

between contacts. The switch should be suitable for the char-

- This appliance is not intended for use by young children

ge indicated on the appliance data plate and must conform to

or in rm persons without supervision

all current legislation (the yellow/green earth wire must not

- Young children should be supervised to ensure they do

be interrupted by the switch).

not play with the appliance

The omnipolar switch must be easy to reach once the instal-

lation process has been completed.

This appliance conforms to the European Directive EC/2002/96,

Waste Electrical and Electronic Equipment (WEEE). By making

USE AND MAINTENANCE

sure that this appliance is disposed of in a suitable manner, the

user is helping to prevent potential damage to the environ-

Maintenance

ment or to public health.

Remove any residues of food and drops of grease from

the cooking surface using the special scraper supplied on

The

symbol on the product or on the accompanying pa-

request (Fig.3)

perwork indicates that the appliance should not be treated as

Clean the heated area as thoroughly as possible using SIDOL,

domestic waste, but should be delivered to a suitable electric

STAHLFIX or similar products and a cloth/paper, then rinse

and electronic appliance recycling collection point.

with water and dry with a clean cloth. Using the special scraper

Follow local guidelines when disposing of waste. For more

(optional) immediately remove any fragments of aluminium

information on the treatment, re-use and recycling of this

and plastic material that have unintentionally melted on the

product, please contact your local authority, domestic waste

heated cooking area or residues of sugar or food with a high

collection service or the shop where the appliance was

sugar content (Fig.3). In this way, any damage to the cooktop

purchased.

surface is prevented. Under no circumstances use abrasive

sponges or irritating chemical detergents such as oven sprays

INSTALLATION INSTRUCTIONS

or stain removers.

These instructions address specialised installers and serve

Use

as a guide for installation, adjustment and maintenance in

Use the touch control system in the corresponding position

conformity with the laws and regulations in force. If a built-in

relative to the individual cooking needs.

oven or any other appliance that generates heat must be  tted

Keep in mind that the higher the number, the more heat that

directly under the glass-ceramic cooktop, THIS APPLIANCE

it is produced.

(oven) AND THE GLASS-CERAMIC COOKTOP MUST BE SUIT-

ABLY INSULATED in such a way that the heat generated by the

oven, measured on the bottom right of the cooktop, does not

- 17 -

Functioning

up function is active, the previously selected temperature

- On the basis of the model you own, the appliance can be

level may be increased by pressing the (+) button. Once the

switched on by actuating the start-up sensor (Fig.4-5-6-7-8

cooking zone has reached the selected temperature, the Heat

A). One zero will appear on all displays within10 seconds. If

up function is automatically deactivated and the hob emits

no display is actuated within 10 seconds, the top will switch

a BEEP. The cooking zone will operate in a constant manner,

o again.

at the set power level.

- Press selection key F for the desired cooking area.

A luminous "0" will appear on the respective display with a

Timer (Fig.5).

decimal point to indicate which cooking area is active.

- Select the plate with the relative power.

- A hotplate may be switched on by activating the "+" or "-"

- Press the selection key again of the already-activated

sensor within 10 seconds. If sensor D is used, the display will

plate.

show selection 9, while if sensor C is used, the display shows

- Using the "+" and "-" keys set the desired time.

selection 1 or 5, depending on the model.

- The decimal point at the side of the power level will indicate

- Once this operation has been performed choose the tem-

that the plate has the TIMER function activated.

perature adjustment with the "+" or "-" keys.

- An acoustic signal will indicate switching o of the cook-

- The plate can be switched o by selecting "0" with the

ing area.

D sensor, after 3 seconds the cooking area is automatically

switched o .

THE MANUFACTURER DECLINES ALL RESPONSIBILITY

It is always possible to switch a plate o by touching the "+"

FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE

and "-" sensors at the same time.

ABOVE WARNINGS.

- The cooking top can be switched o by touching the main

start-up sensor (Fig.4-5-6-7-8 A). If all the plates are selected

on "0" the top will switch o after 10 seconds.

-If the top is equipped with plates with an extension ( g.5- 7-8)

switching on of the second area will be carried out after hav-

ing checked that :

- the key button LED ( g.5-7-8 B) is o , otherwise de-insert

it.

- Press the key ( g.5-7-8 A) to switch the top on.

- Choose the desired plate and adjust the power using the

"+" or "-" keys.

-Once the power has been adjusted choose the key ( g.5-7-8

L) to activate the double area.

- To deactivate the double area check that the interested

plate has been selected (fig.5-7-8 F) and press the key

( g.5-7-8 L) .

Note: the Double area function is activated only on plates

F1 and F2 ( g.5-7-8 ).

- If an object is placed above the controls, the cooking top

will automatically move to the OFF position.

When a plate is in the OFF position and the temperature is

higher than 50° there will be a luminous signal "H" near to

the respective selection key (Fig.4- 5- 6-7-8 H).

- the B function blocks the functioning of the top on selection.

E.g.: if the function is activated while the top has two areas

switched on the programme remains blocked even if you

try to switch another area on. The same thing happens if the

appliance is switched o and the function is activated; the

top doesn't switch on.

To activate or deactivate it hold a  nger on the B sensor for

about two seconds. The function is active when warning light

E is switched on.

Heat up (Rapid heating)

The Heat up function can be used to set the cooking zone

to its maximum temperature for a speci

ed period of time,

after which the temperature will return to a lower value

selected previously.

To activate the Heat up function, select the hotplate by pres-

sing the + button until setting 9 is displayed; if the button is

pressed again a decimal point "" or the letter "A" will appear

on the display (next to the digit 9) for 5 seconds. This means

the Heat up function is active.

The desired power level (between 1 and 8) should be selected

within 5 seconds. If power level 9 is selected, the function is

disabled. To deactivate the Heat up function, simply select the

+ button and hold it down until setting 9 is reached and the

decimal point disappears from the display. When the Heat

- 18 -