Zelmer 919: Vacuum cleaner functions TRADITIONAL CLEANING WITH SAFBAG DUST BAG WET VACUUMING AND WET CLEANING

atomizing nozzle or the large atomizing nozzle until you hear

VACUUM CLEANING WITH THE USE OF THE

a characteristic click.

E

WATER FILTER MODULE

15

Use the following nozzles for the wet vacuuming and wet

1

Press and hold the container lid opening button (2) and

cleaning function or to pick up water: large atomizing nozzle,

lift the container lid.

small atomizing nozzle or the water pick up nozzle.

2

Insert the partition to the grooves in the container so that

16

Slide the stub pipe valve plug downwards.

the shutters are directed downwards. Make sure the partition

●

Insert the stub pipe of the hose to the valve in the

is correctly mounted in the container i.e. the partition ns

vacuum cleaner housing.

should cover the protrusion in the container.

●

Make sure the stub pipe fastenings snap shut.

3

Fill the container with 1,3–1,5 liter of water. The water

level should be in the range marked on the wall of the

ATTENTION! In case of difculties in connecting the

container.

above mentioned elements moisten the gaskets e.g.

with technical vaseline, water, etc.

ATTENTION! Do not operate the appliance with an

empty container while vacuum cleaning with the use

of the water lter module.

Vacuum cleaner functions

4

Cover the container with the lter unit.

TRADITIONAL CLEANING WITH SAFBAG DUST BAG

C

●

Prepare the vacuum cleaner for operation according

1

Press and hold the container lid opening button (2) and

to section B.

lift the container lid.

●

The vacuum cleaner will by default begin operation at the

2

Remove the water lter module from the container

medium power range. 3 diodes will light on the power

(ltration unit and partition).

level indicator (9). Set the desired power value (this

3

Insert the dry ltration module with the SAFBAG (21)

function is only available in vacuum cleaners type 919.0)

dust bag to the container.

by pressing the power adjustment buttons +/- (8).

●

Prepare the vacuum cleaner for operation according

ATTENTION! Do not operate the appliance for too long

to section B.

without replacing the water in the container.

4

The vacuum cleaner will by default begin operation at

the medium power range. 3 diodes will light on the power

WET VACUUMING AND WET CLEANING

F

level indicator (9). Set the desired power value (this function

is only available in vacuum cleaners type 919.0) by pressing

Before using the wet cleaning function thoroughly vacuum

the power adjustment buttons +/- (8).

the surface to be cleaned.

Before operating the vacuum cleaner make sure the container

ATTENTION! The vacuum cleaner is equipped with

is empty and the water lter module and the lters are clean.

a power limiting function should the inlet opening be

1

Press and hold the container lid opening button (2) and

clogged or the SAFBAG dust bag full. It is manifested

lift the container lid.

by a pulsing limitation of the motor power and the

lighting up of the clogged air inlet indicator (11) while

2

Remove the container together with the water lter

the vacuum cleaner is operating at full power (type

module (lter unit and partition) from the vacuum cleaner.

919.0). In such a case switch off the vacuum cleaner

3

Remove the cleaning liquid container (23) by pulling it by

by pressing the on/off button (7), unplug the appliance

the handle and lifting it upwards.

and clear the tubes or replace the SAFBAG dust bag.

4

Open the inlet plug and ll the cleaning liquid container

(23) with the cleaning liquid (the solution of cleaning powder

SAFBAG dust bag disassembly/assembly

D

and water) in the amount indicated below:

●

Remove the dry ltration module with the SAFBAG

(21)

●

Dissolve the content of the bag in a separate container

dust bag from the container.

in 1,5 l of warm water with the maximum temperature

1

Pull the SAFBAG dust bag interlock fastening and pull

of 50°C. The maximum capacity of the cleaning liquid

the interlock aside.

container is 1,7 l.

2

Pull the fastening which attaches the SAFBAG dust bag

●

Close the inlet plug of the cleaning liquid container

to the basket to release the dust bag plate.

5

Insert the cleaning liquid container (23) back to the

3

Remove the dust bag.

previous position and press the container to x it correctly

4

Insert the SAFBAG dust bag according to the arrow

(proceed in the reverse order as in case of removing the

printed on the bag so that the lower part of the bag plate is in

container).

the slot of the housing. Press the upper part of the bag plate

6

Insert the container together with the water lter module

to the fastening until you hear a characteristic click and close

(lter unit and partition) to the vacuum cleaner.

the SAFBAG dust bag interlock.

In order to protect from the foam formation or if foam

●

Insert the dry ltration module with the SAFBAG

(21)

forms during the cleaning process, use the anti-foam

dust bag to the container.