Zelmer 919: Appliance features Preparing the vacuum cleaner for operation Appliance elements

Appliance features

Preparing the vacuum cleaner for operation

B

The vacuum cleaner 919 is intended to pick up dirt from

1

Insert the end of the suction hose to the vacuum cleaner

oors, carpets, ceramic tiles, slots in wood paneling, skirting

opening so that the markings on the hose end and on the

boards, heaters. The vacuum cleaner is also used to vacuum

vacuum cleaner housing are opposite each other and turn

furniture, curtains, to pick up liquids and to wet clean tiles,

oorings, carpets, tted carpets and upholstery.

the hose clockwise to the position .

2

Connect the other end of the hose (handle) with the

Appliance elements

A

telescopic suction tube.

1

Handle

3

Adjust the length of the telescopic suction tube by sliding

the slider according to the arrow and pull out/ pull the tube

2

Container lid opening button

together.

3

Plug and cord

4

Assemble the appropriate nozzle or brush to the other

4

Accessory compartment

end of the suction tube.

5

Pump operation indicator

5

Use the following nozzles and brushes for traditional

6

Pump switch

vacuum cleaning with the SAFBAG dust bag and vacuum

7

cleaning with the use of the water lter module: combination

ON/OFF button

brush with small item separator, small nozzle, small brush,

8

Power adjustment button +/- (type 919.0)

crevice nozzle, parquet brush or turbo brush.

9

Power level indicator (type 919.0)

6

You may assemble a basket for picking up small objects

10

Cord rewind button

in the combination brush with small item separator. In order

11

Clogged air inlet indicator (type 919.0)

to do so remove the basket cover and insert the basket.

12

7

Parquet brush (type 919.0)

To clean hard surfaces – wooden oors, plastic oors,

ceramic tiles etc. pull out the brush by pressing the switch on

13

The vacuum cleaner is equipped with only one type of

the nozzle according to the gure .

suction brush (A or B)

8

The vacuum cleaner is equipped with an accessory

A

Suction-brush

compartment. The compartment opens/closes with the use

B

Combination brush with small item separator

of a slider. To open/close the compartment side the slider

14

Turbo brush (type 919.0 ST)

downwards/upwards and take out/ put away the desired

nozzle.

15

Small brush

9

Close the lid.

16

Small nozzle

10

Grab the plug (3) and pull the cord out of the vacuum

17

Crevice nozzle

cleaner.

18

Telescopic suction tube

19

SAFBAG dust bag (2 pieces)

ATTENTION! While pulling out the cord pay attention

to the yellow stripe which signals the end of the

20

Suction hose

cord. Further attempts (pulling on cord) may result in

21

Dry ltration module with SAFBAG dust bag

damaging the cord.

22

Water lter module (ltration unit + partition)

11

Plug in the appliance.

23

Cleaning liquid container

24

Spray unit – suction hose handle attachment

ATTENTION!!! Before switching on the vacuum

cleaner with the on/off button (7), make sure that the

25

Large atomizing nozzle

appropriate module is installed in the container (see

26

Small atomizing nozzle

section C, E, or F).

27

Water pick up nozzle

12

Switch on the vacuum cleaner by pressing the “on/off”

28

Rubber slat to the large atomizing nozzle

button (7).

29

Cleaning powder

In order to prepare the vacuum cleaner for wet operation

30

Anti-foam agent

additionally:

31

Foam lter I

13

Assemble the spray unit – the suction hose handle

32

Foam lter II

attachment (24).

33

Inlet lter

●

Attach the hose fastenings to the suction hose and the

34

Motor lter

telescopic suction tube.

35

HEPA outlet lter

14

Attach the end of the hose (sleeve) to the telescopic

suction tube and insert the other end of the hose in the small