Zelmer 919: PICKING UP WATER END OF OPERATION CLEANING AND MAINTENANCE

agent recommended by ZELMER S.A. in the amount and

foam is formed. Leave for some time and vacuum with the

manner indicated on the label.

vacuum cleaner.

„G 478 Entschäumer D” manufactured by the company –

ATTENTION! Make sure the carpet is not soaked.

BUZIL, Germany.

It may lead to a permanent deformation of the carpet

●

Prepare the vacuum cleaner for operation according

(folding).

to section B.

PICKING UP WATER

ATTENTION! Use only the large or small atomizing

nozzle for wet vacuum cleaning.

If you want to use the vacuum cleaner to vacuum liquid in

the container, the vacuum cleaner should be prepared as in

●

The vacuum cleaner will by default begin operation at the

the case of vacuum cleaning with the use of the water lter

medium power range. 3 diodes will light on the power

module except that:

level indicator (9). Set the desired power value (this

1. The container should be empty (without water).

function is only available in vacuum cleaners type 919.0)

2. You are to use atomizing nozzles (large or small), large

by pressing the power adjustment buttons +/- (8).

atomizing nozzle with the gathering attachment or the

7

Press the pump switch (6).

nozzle for picking up water.

ATTENTION! The pump may only be switched on when

ATTENTION! Do not operate the vacuum cleaner with

the cleaning liquid container is lled with the solution

a full container! Do not vacuum large amounts of liquid

of cleaning liquid and water. The lack of cleaning liquid

at a time (e.g. with the hose immersed into water).

manifests in a loud operation of the pump.

If the water exceeds the maximum level during vacuuming,

If the nozzle does not atomize water although the pump is

the oat will automatically block the suction. The maximum

switched on, check if the following items are correctly installed:

capacity of the container is about 5 l. In such a case proceed

the cleaning liquid container (press the container), the fastening

in the manner described above in the part concerning the

of the stub pipe in the valve in the base of the vacuum cleaner

blocking of suction caused by a dirty foam lter (pulsating

or the fastening of the hose end in the atomizing nozzle, check

motor speed).

if the atomizing nozzle is not clogged.

END OF OPERATION CLEANING AND MAINTENANCE

8

Press the button adjusting the inow of water to the

●

Switch off the vacuum cleaner by pressing the on/off

nozzle on the hose handle.

button (7) and unplug the appliance.

If you press the button in a pulsating manner, the water shall

●

Wind the cord by pressing the cord rewind button

(10).

temporarily ow in a slower manner to the nozzle, if you

While doing this hold the cord to make sure it is not

press and slide the button backwards, the water shall be

tangled and the plug does not hit the vacuum cleaner

continuously supplied to the nozzle.

housing.

The handle is also equipped with a slider to adjust the suction

●

Turn the end of the hose until the tops of the marks

power. Do not uncover this opening while picking up water or

on the end of the hose end and on the vacuum cleaner

using the wet cleaning function.

housing are in the same position and pull the hose out

ATTENTION! Do not spray the cleaning liquid in one

of the opening.

place on the carpet for too long in order not to soak

●

Remove the stub pipe of the hose by pressing the red

the carpet.

button on the valve and pull the stub pipe.

●

Disconnect the telescopic tube from the hose and the

●

After cleaning one part of the carpet stop the spraying

nozzle or brush.

process and dry the carpet by sliding the nozzle back and

Pour the dirty water out of the container.

forth. Repeat until the whole surface of the carpet is dried.

●

●

It is recommended to wash the container, lters

●

After ending the spraying process switch off the pump

(disassembly below) and partition thoroughly after each

and press the button adjusting the water inow to the

use – changing water several times.

nozzle for a moment to “release the pressure”.

●

After using the wet cleaning function thoroughly wash

ATTENTION! The vacuum cleaner is equipped with a oat

all attachments used in this process (hose, tubes,

which will automatically block the suction if the foam lter

accessories).

II (32) is heavily dirty or the liquid exceeds the maximum

level. It is manifested by a pulsing limitation of the motor

ATTENTION! If you do not clean the above-mentioned

power and the lighting up of the clogged air inlet indicator

parts or clean them insufciently it may lead to the loss

(11) (type 919.0). In such a case switch off the vacuum

of the ltration capabilities of the inserts and foam and

cleaner by pressing the on/off button (7), unplug the

cause the formation of bacteria and mites.

appliance, clean the lter and empty the container.

Dry all the cleaned parts thoroughly before reassembly.

In case of dirt which is difcult to remove moisten the surface

with the washing agent recommended by ZELMER S.A. until