HEIDENHAIN ND 1100 Quick Start: инструкция

Quick Reference Guide

Kurzanleitung

Guide de Démarrage rapide

Guida rapida

Guía rápida de referencia

Snabbreferensguide

Beknopte handleiding

Stručná referenční příručka

Guia de referência rápida

Krótka instrukcja

Краткое руководство

Hızlı Başvuru Kılavuzu

クイックリファレンスガイド

快速參考手冊

ND 1100

QUADRA-CHEK

Software Version

2.16.x

9/2013

ND 1100 QUADRA-CHEK

Front panel

Rear side

Side view

ND 1100 QUADRA-CHEK English

Setup

Very important

Please note

For detailed description, see www.heidenhain.de

For your information

Before Power up

Controls and Displays

Mounting

The ND 1100 is secured to the swivel

A LCD screen

slots of the mounting stand or arm

Electrical connection

B

Soft keys: Change to support

mount by a shoulder screw, a cap

Line voltage: 100 V~ to 240 V~

functions

screw mount is shown and associated

(–15 % to +10 %)

C

Axis keys: Zero or preset datums

washers.

Line frequency: 47 Hz to 63 Hz

D

Command keys: Control

Line fuse: T1600 mA, 250 V

measurement

5 x 20 mm

E

Arrow cursor keys: Menu

navigation

Power connector wiring

F

Fast track keys: Programmable

for frequently used functions

G

Numeric keypad: Enter numeric

data

H

Send key: Transmit

measurement data to PC, USB

printer or USB drive

I

LCD on/off key: Turn LCD on or

off, clear data, datums and skew

alignments

L: Line voltage (brown)

Initial power up

N: Neutral (blue)

• Press the POWER SWITCH to power

Earth ground (yellow/green)

Connections rear side

the ND 1100. The startup screen is

displayed.

1 Power switch

• Press the FINISH key to display the

2 Power connection with fuse

current axis positions on the DRO

3

Ground (protective ground)

Danger of electrical shock!

screen.

• Do not open the enclosure

4

Encoder inputs, X, Y, Z, Q axis

• Never use 3-wire to 2-wire adapters

for linear and rotary encoders.

or allow the ground connection to

Interface specified at the time of

the ND 1100 to be interrupted or

purchase.

disconnected.

5

RS-232-C interface for PC

connection. RS-232 cable must

not include crossovers.

Caution

6 Touch probe connector

Changes to the power cable may be

(optional)

made only by an electrical technician.

7 Unused

Caution

Software setup

Do not connect encoders or other

Connections side view

The operating parameters of the

equipment to the ND 1100 when the

8

Audio out, for 3,5 mm

ND 1100 must be configured prior

power is on.

headphone /speaker jack,

to using it for the first time, and any

monaural, 8 Ohm

time measurement, reporting or

9

USB type A interface for printer

communication requirements change.

Safety Considerations

or data storage

General accepted safety precautions

Settings will be retained until:

10

Remote accessory interface

must be followed when operating the

• The data-backup battery is changed

RJ-45 for optional foot switch or

ND 1100. Failure to observe these

• The data and settings are cleared

keypad accessory. Two optional

precautions could result in damage to

• Software upgrades are performed

remote accessories can be used

the equipment, or injury to personnel.

simultaneously using an RJ-45

It is understood that safety rules within

splitter.

individual companies vary. If a conflict

Caution

exists between the material contained

Setup parameters control the operation

in this guide or the and the rules of a

of the ND 1100 and are password-

company using this system, the more

protected. Only qualified personnel

stringent rules should take precedence.

should be given password access to

setup screens.

1. Access setup menu

Press the MENU key and then press

the SETUP soft key. The setup menu is

displayed.

1