AEG mrc 4132 bt: English

English

35

Bottom side (not shown)

CAUTION:

Battery compartment (power reserve)

• Differentbatteriesornewandusedbatteriesmaynot

be used together.

First Use of the Device/Introduction

• Batteriesmustnotbedisposedofinthegarbage.

Please bring used batteries to competent collection

• Selectaproperplaceforthedevice.Adry,levelandslip

centers or back to the dealer.

proof surface is suitable.

• Makesurethedeviceisventedsufciently!

USB Charging Socket (3)

• Removetheprotectivelmfromthedevice,ifpresent.

You can charge your Smartphone through this jack. Use the

Power supply

USB cable of your Smartphone for the connection.

• Makesurethegridvoltagecorrespondstothegureson

NOTE:

the rating plate.

• DuetothedifferentSmartphonetypesthatareoffered

• Plugthepowersupplyunitintoaproperlyinstalled

today, and their different charging capacities, the load-

protective contact socket.

ing duration is dependent on the Smartphone used

• Connectthedevicewiththepowersupplyunitbyplug-

and its operating condition.

ging the jack of the power supply unit into the “DC IN

• Aplaybackofaudio-lesthroughthisconnectorisnot

5 V 2 A

“ jack.

possible.

CAUTION:

• Thisdeviceshouldonlybeusedwiththemainssupply

General Operation

unit (included). Do not use it for other devices.

• Onlyusea5Vpowersupplyunit(

). A different

Switch device on/off

supply unit may damage the device.

• PressthePOWER/FUNCTIONbutton(1)toturnonthe

device.

NOTE:

• Toshutoffthedevice,keepthePOWER/FUNCTION

• Disconnectfrommainspowersupplyduringlonger

button pressed for a short time. The “OFF” notification

periods of non-use.

will appear in the display.

• Ifyoudidnotinsertanotherreservebattery,thetime

• Todisconnecttheunitcompletelyfromthemains,pull

and the station memory will be lost as soon as the

the mains plug from the socket.

power supply is interrupted.

Volume

Inserting the reserve batteries

By pressing the VOLUME+/AL1 / VOLUME-/AL2 buttons (7/6)

(Batteries are not included in the scope of delivery)

you can adjust the desired volume.

In case of power failure or if the power supply unit is pulled

from the plug, the settings are maintained if the reserve bat-

POWER/FUNCTION (1)

teries are inserted.

Press the POWER/FUNCTION button (1) until the desired

operating mode is shown on the display.

• Openthebatterycompartmentonthebottomside.

To do so, remove the screw on the cover of the battery

Display brightness

compartment with a Philips screwdriver.

• InserttwotypeAAA/R031.5Vbatteries.Checkthatthe

While in standby, press the SNOOZE/SLEEP/DIMMER but-

polarity is correct (see battery compartment).

ton (10) to adjust the brightness of the display.

• Closethebatterycompartment.Re-securethebattery

compartment with the screw.

Setting the time (in standby)

1. Keep the MEMORY/SET button (2) pressed for a short

If the device is not used for a longer period of time, remove

time. The hour display will start to flash.

the batteries to avoid battery acid from “leaking out”.

2. Perform the setting with the

/ buttons (5).

WARNING:

3. Press the MEMORY/SET button again. The minute

Donotexposethebatteriestointenseheat,suchassun-

display will start to flash.

light, fire or similar. Danger of explosion!

4. Perform the setting with the

/ buttons.

5. Following this, press the MEMORY/SET button again to

store the time.