BEST CIRRUS: English
English: BEST CIRRUS
English
! The appliance must be installed by a qualied person
in compliance with the instructions provided.
10
!
CONTROLS
Wear gloves when carrying out installation and
maintenance operations.
AIR VENT
(for ducting versions)
! Prepare the hole and the air vent duct (150 mm dia-
meter).
! Use a duct of the minimum indispensible length.
! Use a duct with as few elbows as possible (maximum
elbow angle: 90°).
! Avoid drastic changes in the duct cross-section.
! Use a duct with an as smooth as possible inside.
! The duct must be made of certied material.
! Do not connect the hood to smoke exhaust ducts
for the products of combustion (boilers, replaces,
stoves, etc).
! For the air vents comply with the provisions laid down
by the competent authorities.
In addition, the air must not be evacuated through a
hole in the wall unless specically intended for this
purpose.
! Fit air intakes in the room to prevent the hood from
creating a negative pressure in the room (which must
not exceed 0.04 mbar); if the hood is used at the
same time as non-electrical equipment (gas-, oil- and
charcoal-red stoves, etc.) the exhaust gas may be
sucked in by the heat source.
Ducting version
The hood puries the air and evacuates it to the outside
through an exhaust duct (diameter 150 mm).
P1
P3 P4
P
1
P2
EN
P1: 5’ TIMER
P2: Filter alarm reset
P3: Motor off / speed decrease – .
- holding down the button, the motor turns off sto-
ring the current speed
P4: Motor on / speed increase
P5: Lights on/off
L1 Signalling crown:
- Hood in standby: lights up amber-orange. 30” after
the last key has been pressed the crown turns off
- Motor on: L1 lights up turquoise ashing. The
ashing frequency is proportional to the speed
- 5’ TIMER function : L1 lights up turquoise xed
- Filter alarm active: L1 lights up red xed (30h); L2
lights up red ashing (120h)
MAINTENANCE
MALFUNCTIONS
EN
! Before cleaning or maintenance cut the power.
If something appears not to be working properly, do the
following simple checks before calling Technical Servi-
Cleaning the hood
ce:
WHEN TO CLEAN IT: clean it at least every 2 months
to prevent the risk of re.
• If the hood is not working:
EXTERNAL CLEANING: use a cloth moistened in luke-
Check that:
warm water and neutral detergent (for painted hoods);
- The power has not been disconnected.
use specic products for steel, copper or brass hoods.
- A speed has been selected.
INTERNAL CLEANING: use a cloth (or brush) soaked
in denatured ethyl alcohol.
• If the hood performs inefciently:
WHAT NOT TO DO: do not use abrasive or corrosive
Check that:
products (e.g. metal sponges, brushes, too hard bru-
- The motor speed selected is sufcient for the amount
shes, very aggressive detergents, etc.)
of smoke and vapours released.
- The kitchen is sufciently ventilated to allow air inta-
ke.
WHEN TO CLEAN IT: clean it at least every 2 months to
- The charcoal lter is not worn (hood in ltering ver-
prevent the risk of re.
sion).
HOW TO REMOVE THE FILTERS: push the catch near
the handle towards the rear of the hood and pull the
• If the hood has turned off during normal functioning:
lter downwards
Check that:
HOW TO CLEAN THE FILTERS: hand wash or in the
- The power has not been disconnected.
dishwasher using a neutral detergent. If washing in the
- the omnipolar disconnection device has not tripped.
dishwasher, possible discoloration of the lters does not
in any way compromise their functioning.
Components not provided with the product
Replacing the LEDS
- Replace with leds of the same type.
11
