Zelmer 829: VACUUM CLEANING WITH THE USE OF THE WATER FILTER MODULE PICKING UP WATER End of operation cleaning and maintenance

61

3

 Insert the dry 

fi

 ltration module with the SAFBAG 

(25) 

dust bag to the container.

Prepare the vacuum cleaner for operation according 

●

to section B.

4

 The vacuum cleaner starts up with default setting of the 

highest power range. One diode will light on the power level 

indicator 

(6)

. Set the desired power value (this function is 

only available in vacuum cleaners type 829.0) by pressing 

the power adjustment buttons  ,  

(5)

.

ATTENTION! It is strictly prohibited to vacuum without 

the dust bag and the inlet 

fi

 lter or with a damaged 

dust bag. It may cause a failure of the vacuum cleaner 

motor.

SAFBAG dust bag disassembly/assembly

Remove the dry 

fi

 ltration module with the SAFBAG 

●

(25)

dust bag from the container.

ATTENTION! The water 

fi

 lter module/the dry 

fi

 ltration 

module with the SAFBAG dust bag may only be 

removed and inserted when the end of the hose is 

removed from the vacuum cleaner opening.

1

 Pull the SAFBAG dust bag interlock fastening and pull 

the interlock aside.

2

 Pull the fastening which attaches the SAFBAG dust bag 

to the basket to release the dust bag plate.

3

 Remove the dust bag.

4

 Insert the SAFBAG dust bag according to the arrow 

printed on the bag so that the lower part of the bag plate is in 

the slot of the housing. Press the upper part of the bag plate 

to the fastening until you hear a characteristic click and close 

the SAFBAG dust bag interlock.

Insert the dry 

fi

 ltration module with the SAFBAG 

●

(25)

dust bag to the container.

VACUUM CLEANING WITH THE USE OF THE 

WATER FILTER MODULE

1

 Press the “PRESS” button and remove the tank lid.

2

 Insert the partition to the grooves in the container so that 

the shutters are directed downwards. Make sure the partition 

is correctly mounted in the container i.e. the partition 

fi

 ns 

should cover the protrusion in the container.

3

 Fill the container with 1,2 liter of water. The water level 

should be in the range marked on the tank wall.

ATTENTION! Do not operate the appliance with an 

empty container while vacuum cleaning with the use 

of the water 

fi

 lter module.

4

 Insert the 

fi

 ltration unit to the tank, make sure that the two 

air stub pipes are in the openings of the vacuum cleaner body.

Prepare the vacuum cleaner for operation according 

●

to section B.

The vacuum cleaner starts up with default setting of the 

highest power range. One diode will light on the power level 

indicator 

(6)

. Set the desired power value (this function is 

only available in vacuum cleaners type 829.0) by pressing 

the power adjustment buttons  ,  

(5)

.

ATTENTION! Do not operate the appliance for too 

long without replacing the water in the container. 

In case of long-term or very intensive vacuuming 

of large amounts of dirt, the water in the tank which 

constitutes the 

fi

 rst 

fi

 ltration level may in whole or in 

a considerable part be absorbed by the dirt. In such 

a case, exchange the water and continue vacuuming.

Avoid vacuuming surfaces covered with substances which 

may favor an excessive foaming of the water inside the 

tank. If you notice that the water is heavily foamed, add 

a foam neutralizer recommended by the manufacturer of 

the appliance e.g. “G 478 Entschäumer D” in the amount 

indicated on the packaging. It can be purchased in stores 

which offer ZELMER S.A. products or by mail order.

ATTENTION! Vacuuming with the amount of water in 

the tank which exceeds the marked, permissible level 

may cause the water to spill to the outside of the 

appliance. If this situation repeats often, it may lead to 

a fast clogging of the outlet HEPA 

fi

 lter.

ATTENTION! The vacuum cleaner is equipped with 

a 

fl

 oat which will automatically block the suction if the 

foam 

fi

 lter II (9) is heavily dirty or the liquid exceeds the 

maximum level. In such a case switch off the vacuum 

cleaner by pressing the on/off button (1), unplug the 

appliance, clean the 

fi

 lter and empty the container.

PICKING UP WATER

If you want to use the vacuum cleaner to vacuum liquid, the 

vacuum cleaner should be prepared as in the case of vacuum 

cleaning with the use of the water 

fi

 lter module except that:

1

 The container should be empty (without water).

2

 You should use the nozzle for picking up water 

(21)

.

ATTENTION! Do not operate the vacuum cleaner with 

a full container! Do not vacuum large amounts of liquid 

at a time (e.g. with the hose immersed into water).

If the water exceeds the maximum level during vacuuming, 

the 

fl

 oat will automatically block the suction. The maximum 

capacity of the container is about 4,0 l. In such a case proceed 

in the manner described above in the part concerning the 

blocking of suction caused by a dirty foam 

fi

 lter.

End of operation cleaning and maintenance

Switch off the vacuum cleaner by pressing the on/off 

●

button 

(1)

 and unplug the appliance.

Wind the cord by pressing the cord rewind button 

●

(4)

. While 

doing this hold the cord to make sure it is not tangled and 

the plug does not hit the vacuum cleaner housing.

Press the interlock on the hose end and remove the hose 

●

from the opening.

E D