Zelmer 829: Filter disassembly FOAM FILTER II INLET FILTER MOTOR FILTER OUTLET HEPA FILTER AND FOAM FILTER III

62

Disconnect the telescopic tube from the hose and the 

●

nozzle or brush.

In case of vacuuming or picking up water with the use 

●

of the water 

fi

 lter module, remove the dirty water from 

the tank.

It is recommended to wash the container, 

fi

 lters 

●

(disassembly below) and partition thoroughly after each 

use – changing water several times.

ATTENTION! If you do not clean the above-mentioned 

parts or clean them insuf

fi

 ciently it may lead to the loss 

of the 

fi

 ltration capabilities of the inserts and foam and 

cause the formation of bacteria and mites.

Dry all the cleaned parts thoroughly before reassembly.

Filter disassembly

FOAM FILTER I

1

 Open the lid of the 

fi

 lter unit – press the handle and lift 

the lid.

2

 Take out the 

fi

 lter, wash it under running water, dry and 

reinsert.

Close the 

fi

 lter unit lid by pressing it until you hear 

●

a characteristic click.

FOAM FILTER II

It is recommended to wear rubber protective gloves while 

dismantling the 

fi

 lter.

1

 Grab the foam 

fi

 lter with your 

fi

 ngers and remove it from 

the 

fi

 lter unit body.

2

 Wash under running water, dry and reinsert.

ATTENTION! Do not hand wash the 

fi

 lter foam, do not 

wring it, do not wash it in washing machines. Avoid 

crumpling, stretching and deforming. After cleaning 

dry the foam in room temperature. Never dry the foam 

on heaters, stoves, etc.

INLET FILTER

1

 Press the “PRESS” button and remove the tank lid.

2

 Remove the SAFBAG 

(25)

 dust bag module from the 

container.

3

 Take out the SAFBAG dust bag from the module (see 

chapter TRADITIONAL CLEANING WITH SAFBAG DUST 

BAG – disassembly/assembly of the SAFBAG dust bag).

4

 Release the fastening hook which 

fi

 xes the lid of the 

SAFBAG dust bag module with the basket and pull the 

basket aside.

5

 Take out the 

fi

 lter, wash it under running water, dry and 

reinsert.

6

 Close the basket of the SAFBAG dust bag module by 

pressing it until you hear a characteristic click.

7

 Insert SAFBAG dust bag (see chapter TRADITIONAL 

CLEANING WITH SAFBAG DUST BAG – disassembly/

assembly of the SAFBAG dust bag).

8

 Insert the dry 

fi

 ltration module with the SAFBAG 

(25) 

dust bag into the tank.

Insert and snap the tank lid shut.

●

MOTOR FILTER

A 

fi

 ltration fabric is inserted in the motor cooling cycle which 

is to catch the coal dust which arises due to the natural wear 

and tear of the brushes and the commutator in the motor.

1

 Remove the tank from the vacuum cleaner.

2

 Place the vacuum cleaner with the “wheels upwards” so 

that the upper sloping surface and the handle are rested on 

the 

fl

 oor. Insert a 

fl

 at, narrow tool e.g. a screwdriver into the 

special slot of the 

fi

 lter lid; pry the fastening with an upward 

hand movement (lever principle) which will release the lid 

latch while being bent.

3

 If the motor 

fi

 lter 

(8)

 is dirty, it is possible to rinse the 

fi

 lter 

(8)

 under running water. Remember to dry the above 

mentioned 

fi

 lter before reassembly.

4

 Insert the new/rinsed motor 

fi

 lter 

(8)

, make sure that the 

fi

 lter edges do not remain outside the outline of the section. 

Snap the 

fi

 lter lid shut by 

fi

 rst inserting the lower fastening 

and then pressing the fastening so that the upper fastening 

clicks into place at the edge of the appliance body.

OUTLET HEPA FILTER AND FOAM FILTER III

The HEPA outlet 

fi

 lter should be replaced after about 30 

hours of operation (6 months) or earlier in case of heavy dirt.

1

 Remove the tank from the vacuum cleaner.

2

 Place the vacuum cleaner with the “wheels upwards” so 

that the upper sloping surface and the handle are rested on 

the 

fl

 oor.

3

 Slide the slider of the 

fi

 lter cover interlock to the “open” 

position and remove the 

fi

 lter lid.

4

 Remove the foam 

fi

 lter  III 

(11)

. Rinse or replace if the 

fi

 lter becomes dirty. Remember to dry the 

fi

 lter  before 

reassembly.

5

 Remove the foam 

fi

 lter III 

(11)

 and next remove the HEPA 

fi

 lter by grabbing the handle. Replace with a new one if the 

fi

 lter becomes dirty.

It is recommended to periodically inspect the condition of the 

fi

 lter, especially if there was a water over

fl

 ow to the outside of 

the vacuum cleaner. In case of detecting damage (a break) 

in the 

fi

 lter layer or if the layer is evenly covered with dust, 

the 

fi

 lter should be replace with a new one.

6

 If the HEPA 

fi

 lter is dirty, replace it with a new one or 

rinse under running water. Remember to dry the 

fi

 lter before 

reassembly.

7

 Reinsert the 

fi

 lters, insert the 

fi

 lter lid and press 

fi

 rmly.

8

 Slide the slider of the 

fi

 lter cover interlock to the “closed” 

position.

Turn the vacuum cleaner to its natural position (on four 

wheels).

F G H I J