JVC KD-SHX851 – страница 3
Инструкция к Радиомагнитоле СD c кассетной декой JVC KD-SHX851
General settings — PSM
3 Adjust the setting.
Basic procedure
You can change PSM (Preferred Setting Mode)
items listed in the table that follows.
ENGLISH
4 Repeat steps 2 and 3 to adjust the
1 Enter the PSM menu (see page
5).
other PSM items if necessary.
2 Select a PSM item.
5 Finish the procedure.
Ex.: When “Scroll” is selected
Indications Selectable settings, [reference page]
Demo/Link
Demo: [Initial]; Display demonstration (animation) appears.
Display
ImageLink: To show a still image while playing back an
demonstration
MP3/WMA track, [17, 19, 58].
Off: Cancels.
• These graphics appear if no operation is done for about 45 seconds.
WallPaper
You can select the background screen of the display window.
Wall paper
Standard 1 [Initial] O Standard 2 O Standard 3
O (back to the beginning)
LevelMeter
You can select the level meter.
Audio level meter
Meter1 [Initial] O Meter2 O Meter3 O (back to the beginning)
• Press DISP repeatedly to show the selected level meter.
PICT
You can activate the graphic screen using either movie or picture, [40].
Pictures
Select the picture size first.
Large: [Initial]; 256 x 64 pixel (full screen size)
Small: 64 x 64 pixel (CD jacket image)
After select the picture size, you can select one of the following items
separately for “Large” and “Small.”
Picture: [Initial]; One of your edited still images stored in
“Picture” is activated.
Slideshow: All stored still images are activated and shown in
sequence (UserSlide).
Movie: Your edited animation stored in “Movie” is activated.
• Press DISP repeatedly to show the selected graphics.
To be continued....
41
EN41-48_KD-SHX851[EY]f.indd 41EN41-48_KD-SHX851[EY]f.indd 41 05.4.11 1:59:20 PM05.4.11 1:59:20 PM
Indications Selectable settings, [reference page]
Clock Hr
0 – 23 (1 – 12), [9]
Clock hour
[Initial: 0 (0:00)]
ENGLISH
Clock Min
00 – 59, [9]
Clock minute
[Initial: 00 (0:00)]
24H/12H
12H (Hours) O 24H (Hours), [9]
Clock system
[Initial: 24H]
Clock Adj
Auto: [Initial]; The built-in clock is automatically adjusted using the
Automatic clock
CT (clock time) data in the RDS signal.
adjustment
Off: Cancels.
Scroll
Once: [Initial]; For disc information: scrolls the disc information only
Scroll mode
once.
For RDS Radiotext: scrolls the text message continuously.
For DAB text: scrolls the detailed DAB text.
Auto: For disc information: repeats the scroll (in 5-second intervals).
For RDS Radiotext: scrolls the text message continuously.
For DAB text: scrolls the detailed DAB text.
Off: For disc information: cancels.
For RDS Radiotext: shows only the first page of the text
message.
For DAB text: shows only headline if any.
• Holding DISP for more than one second can scroll the disc
information regardless of the setting.
Dimmer
Auto: [Initial]; Dims the display when you turn on the headlights.
Dimmer mode
Time Set: Sets the timer for dimmer, [45].
Off: Cancels.
On: Activates dimmer.
1
From–To*
Any hour – Any hour, [45]
Dimmer time
[Initial: 18:00 – 7:00]
42
EN41-48_KD-SHX851[EY]f.indd 42EN41-48_KD-SHX851[EY]f.indd 42 05.4.11 1:59:21 PM05.4.11 1:59:21 PM
Indications Selectable settings, [reference page]
Bright
1 – 8: Adjust the display brightness to make the display indications
Brightness
clear and legible.
ENGLISH
[Initial: 8]
Tag
On: [Initial]; To show the ID3 tag display while playing MP3/WMA
Tag display
tracks, [17, 18, 20].
Off: Cancels.
PTyStandby
You can select one of the PTY codes for the PTY Standby Reception,
PTY Standby
[15].
[Initial: News]
AF-Regn’l
When the received signals from the current station become weak...
Alternate frequency/
AF: [Initial]; Switches to another station (the programme may
Regionalization
differ from the one currently received), [16].
reception
• The AF indicator lights up.
AF Reg: Switches to another station broadcasting the same
programme.
• The REG indicator lights up.
Off: Cancels (not selectable when “DAB AF” is set to “On”).
TA Volume
When a traffic programme (TA) is received, the volume level
Traffic announcement
automatically changes to the preset level.
2
volume
[Initial: 15]; 0 – 30 or 0 – 50*
P-Search
On: The receiver tunes in to another frequency broadcasting the
Programme search
same programme as the original preset RDS station is if the
preset station signals are not sufficient.
Off: [Initial]; Cancels.
IF Filter
Auto: [Initial]; Increases the tuner selectivity to reduce interference
Intermediate
noises between the stations. (Stereo effect will be lost.)
frequency filter
Wide: Subject to the interference noises from adjacent stations, but
sound quality will not be degraded. (Stereo effect will not be
lost.)
1
*
Displayed only when “Dimmer” is set to “Time Set.”
2
*
Depends on the amplifier gain control.
To be continued....
43
EN41-48_KD-SHX851[EY]f.indd 43EN41-48_KD-SHX851[EY]f.indd 43 05.4.11 1:59:21 PM05.4.11 1:59:21 PM
Indications Selectable settings, [reference page]
1
DAB AF*
On: [Initial]; Traces the programme among DAB services and FM
Alternative Frequency
RDS stations, [53].
ENGLISH
Reception
• The AF indicator lights up.
Off: Cancels.
1
Announce*
Select one of the 9 announcement types for Announcement Standby
Announcement
Reception.
Standby Reception
Travel [Initial] O Warning O News O Weather O Event O
Special O Rad Inf (Radio Information) O Sports O Finance O
(back to the beginning)
2
Ext Input*
Changer: [Initial]; To use a JVC CD changer, [18].
External input
Ext Input: To use any external component other than above, [48].
Beep
On: [Initial]; Activates the key-touch tone.
Key-touch tone
Off: Deactivates the key-touch tone.
Telephone
Muting1/Muting2: Select either one which mutes the sounds while
Telephone muting
using the cellular phone.
Off: [Initial]; Cancels.
• If CD or CD changer has been selected as the source, playback pauses
during telephone muting.
Amp Gain
You can change the maximum volume level of this receiver.
Amplifier gain control
HighPower: [Initial]; Volume 00 – Volume 50
Low Power: Volume 00 – Volume 30 (Select this if the maximum
power of the speaker is less than 70 W to avoid
damaging the speakers.)
Off: Deactivates the built-in amplifier.
1
*
Displayed only when the DAB tuner is connected.
2
*
Cannot be selected if the source is “CD-CH” or “EXT-IN.”
44
EN41-48_KD-SHX851[EY]f.indd 44EN41-48_KD-SHX851[EY]f.indd 44 05.4.11 1:59:21 PM05.4.11 1:59:21 PM
4 Enter the Time Set screen.
Selecting the dimmer mode
You can dim the display at night or as you set
the timer.
ENGLISH
1 Enter the PSM menu (see page
5).
2 Select “Dimmer.”
5 Adjust the dimmer time.
1 Set the dimmer start time.
3 Select a setting.
Auto:
Dims the display when you
2 Set the dimmer end time.
turn on the headlights.
\ Go to step 6.
Time Set:
Sets the timer for dimmer.
\ Go to step 4.
Off:
Cancels.
\ Go to step 6.
On:
Always dims the display.
\ Go to step 6.
6 Finish the procedure.
45
EN41-48_KD-SHX851[EY]f.indd 45EN41-48_KD-SHX851[EY]f.indd 45 05.4.11 1:59:21 PM05.4.11 1:59:21 PM
Other main functions
2 Select a character.
Assigning titles to the sources
• For available characters,
You can assign titles to CDs (both in this
see page 54.
receiver and in the CD changer) and the
ENGLISH
external components (LINE-IN and EXT-IN).
3 Move to the next (or previous)
character position.
Sources Maximum number of characters
CDs/CD-CH* Up to 32 characters (up to 30
discs)
External
Up to 16 characters
4 Repeat steps 1 to 3 until you
components
finish entering the title.
*
You cannot assign a title to a CD Text or an
MP3/WMA disc.
4 Finish the procedure.
1 Select the source.
• For a CD in this receiver: Insert a CD.
• For CDs in the CD changer: Select
“CD-CH,” then select a disc number.
• For external components: Select
• To cancel the title entry without
“EXT-IN” or “LINE-IN” (see page 48).
registration, press MENU.
2 Enter the TITLE menu (see page
5).
To erase the entire title
In step 3 on the left...
3 Assign a title.
1 Select a character set.
DISP
DISP
(A – Z: upper case)
(a – z: lower case)
(Numbers and symbols)
(Accented letters:
upper case)
(Accented letters:
lower case)
Ex.: When you assign a title to a CD
46
EN41-48_KD-SHX851[EY]f.indd 46EN41-48_KD-SHX851[EY]f.indd 46 05.4.11 1:59:22 PM05.4.11 1:59:22 PM
Changing the control panel angle
Detaching the control panel
When detaching or attaching the control panel,
be careful not to damage the connectors on
ENGLISH
the back of the control panel and on the panel
holder.
The control panel changes its angle as follows:
Detaching the control panel
Before detaching the control panel, be sure to
turn off the power.
Angle 1
Angle 2
Angle 4
Angle 3
When using the remote controller...
Attaching the control panel
Caution:
Do not insert your finger behind the control
panel.
47
EN41-48_KD-SHX851[EY]f.indd 47EN41-48_KD-SHX851[EY]f.indd 47 05.4.11 1:59:22 PM05.4.11 1:59:22 PM
External component operations
Playing an external component
SOURCE
ENGLISH
You can connect an external component to the
EXT-IN: For selecting the external
LINE IN plugs on the rear.
component connected to the
CD changer jack.
You can also connect an external component to
the CD changer jack on the rear using the Line
Input Adapter KS-U57 (optionally purchased)
or Aux Input Adapter KS-U58 (optionally
purchased).
• If you have changed the “Ext Input”
Before operating the external component, select
setting to “Changer” (see page 44),
the external input correctly (see page 44).
you cannot select “EXT-IN.”
• For connection, see Installation/Connection
Manual (separate volume).
Ÿ Turn on the connected component
and start playing the source.
SOURCE
~
! Adjust the volume.
LINE-IN: For selecting the external
component connected to the
LINE IN plugs.
⁄ Adjust the sound as you want.
(See pages 25 – 35.)
48
EN41-48_KD-SHX851[EY]f.indd 48EN41-48_KD-SHX851[EY]f.indd 48 05.4.11 1:59:22 PM05.4.11 1:59:22 PM
DAB tuner operations
Listening to the DAB tuner
SOURCE
ENGLISH
BAND
SOURCE
~
! Start searching for an ensemble.
BACK
Ÿ
BAND
When an ensemble is received,
searching stops.
To stop searching, press the same
Preset
button again.
Current
number
Programme
band
(if any)
type
⁄ Select a service (either primary or
secondary) to listen to.
Ensemble
1
2
3
Service
*
*
*
label
label
1
*
ANN indicator: See page 52.
2
*
AF indicator: See page 44.
To tune in to an ensemble manually
3
*
DRC indicator: See page 50.
In step ! on the left...
Activate “Manual
Select ensemble
Search”
frequencies
49
EN49-53_KD-SHX851[EY]f.indd 49EN49-53_KD-SHX851[EY]f.indd 49 05.4.11 2:00:02 PM05.4.11 2:00:02 PM
3 Select one of the DRC signal levels (1,
What is DAB system?
2, or 3).
DAB can deliver digital quality sound
without any annoying interference and
signal distortion. Furthermore, it can carry
ENGLISH
text, pictures, and data. When transmitting,
(Cancels)
DAB combines several programmes (called
“services”) to form one “ensemble.” In
addition, each “service”—called “primary
service”—can also be divided into its
components (called “secondary service”).
The reinforcement level increases from 1
A typical ensemble has six or more
to 3.
programmes (services) broadcast at the same
time.
4 Finish the procedure.
By connecting the DAB tuner, this receiver
can do the following:
•
Tracing the same programme automatically
—Alternative Frequency Reception (see
“DAB AF” on page 44).
It is recommended to use DAB (Digital
Audio Broadcasting) tuner KT-DB1000
with your receiver. If you have another
DAB tuner, consult your JVC IN-CAR
ENTERTAINMENT dealer.
• Refer also to the Instructions supplied for
DRC indicator appears.
your DAB tuner.
• The DRC indicator will be highlighted
only when receiving DRC signals from
the tuned service.
When surrounding sounds are noisy
Some service provides Dynamic Range Control
To search for your favorite service
(DRC) signals together with their regular
programme signals. DRC will reinforce the low
You can search for either Dynamic or Static
level sounds to improve for your listening.
PTY codes.
• Operations are exactly the same as explained
on pages 13 and 14 for FM RDS stations.
1 Enter the MODE menu (see page
5).
• You cannot store PTY codes separately for
the DAB tuner and the FM tuner.
2 Select “DRC.”
• Search will be performed on the DAB tuner
only.
50
EN49-53_KD-SHX851[EY]f.indd 50EN49-53_KD-SHX851[EY]f.indd 50 05.4.11 2:00:03 PM05.4.11 2:00:03 PM
• If you press 4/¢ ( / ), you can
Storing DAB services in memory
display the lists of the other DAB bands,
but cannot store a service for the other
You can preset six DAB services (primary) for
bands.
each band.
ENGLISH
Ex.: Storing an ensemble (primary service) into
8 Store the service.
the preset number 1 of the DAB1 band.
1
SOURCE
BACK
2
BAND
When using the remote controller...
After tuning in to a service you want to
preset
3 Select an ensemble (primary service).
• By holding 5/∞, the Preset Service List
will also appears (see step 7 below).
Tuning in to a preset DAB service
4 Enter the MODE menu (see page
5).
1
SOURCE
5 Select “List.”
BACK
2
BAND
6
3 Perform steps 4 to 7 (on the left
column) to enter the Preset Service
List.
4
7 Select a preset number.
To be continued....
51
EN49-53_KD-SHX851[EY]f.indd 51EN49-53_KD-SHX851[EY]f.indd 51 05.4.11 2:00:03 PM05.4.11 2:00:03 PM
To activate the Announcement Standby
When using the remote controller...
Reception
To directly select the preset service
1 Enter the MODE menu (see page
5).
ENGLISH
2 Select “Announce.”
3 Select an announce type.
Using the Standby Receptions
Selected announcement type
TA (Road Traffic News) Standby
Reception
• Operations are exactly the same as explained
on page 15 for FM RDS stations.
• You cannot activate TA Standby Reception
separately for the DAB tuner and for FM
4 Finish the procedure.
tuner.
• The volume changes to the preset TA volume
level (see page 43).
PTY Standby Reception
• Operations are exactly the same as explained
ANN indicator appears.
on page 15 for FM RDS stations.
• PTY Standby Reception for DAB tuner works
• If the ANN indicator lights up,
only using a dynamic PTY code.
Announcement Standby Reception is
• You can neither store your favorite PTY nor
activated.
activate PTY Standby Reception separately
• If the ANN indicator flashes,
for the DAB tuner and for the FM tuner.
Announcement Standby Reception is not
• You can activate and deactivate PTY Standby
yet activated.
Reception when the source is either “FM” or
To activate, tune in to another service
“DAB.”
providing these signals. The ANN
indicator will stop flashing and remain
lit.
Announcement Standby Reception
Announcement Standby Reception allows the
To deactivate the Announcement Standby
receiver to switch temporarily to your favorite
service (announcement type).
Reception
Select “Off” in step 3 above.
To select your favorite announcement type,
The ANN indicator goes off.
see page 44.
52
EN49-53_KD-SHX851[EY]f.indd 52EN49-53_KD-SHX851[EY]f.indd 52 05.4.11 2:00:03 PM05.4.11 2:00:03 PM
To show the Dynamic Label Segment (DLS)
Tracing the same programme—
information
Alternative Frequency Reception
DISP
ENGLISH
You can keep listening to the same
programme by activating the Alternative
Frequency Reception.
• While receiving a DAB service:
When driving in an area where a DAB service
cannot be received, this receiver automatically
tunes in to another ensemble or FM RDS
station, broadcasting the same programme.
• While receiving an FM RDS station:
When driving in an area where a DAB service
Service frequency is displayed.
is broadcasting the same programme as the
FM RDS station is broadcasting, this receiver
automatically tunes in to the DAB service.
While listening to an ensemble that
supports DLS...
When shipped from the factory, Alternative
Frequency Reception is activated.
To deactivate the Alternative Frequency
Reception, see page 43.
*
Dynamic Label Segment (DLS—
DAB radio text information) is
displayed.
* Lights up when receiving a service
providing DLS.
•
The DLS screen will be temporarily canceled
when you operate the receiver.
To show whole text at once, press and hold
DISP while DLS is displayed.
Multi-line text screen appears.
• When the text contains more than 96
characters, another window appears to show
the rest of the text.
To restore the previous screen, press and hold
DISP again.
53
EN49-53_KD-SHX851[EY]f.indd 53EN49-53_KD-SHX851[EY]f.indd 53 05.4.11 2:00:04 PM05.4.11 2:00:04 PM
Maintenance
How to clean the connectors
To keep discs clean
Frequent detachment will deteriorate the
A dirty disc may not play correctly.
connectors.
If a disc does become dirty, wipe
To minimize this possibility, periodically wipe
it with a soft cloth in a straight line
ENGLISH
the connectors with a cotton swab or cloth
from center to edge.
moistened with alcohol, being careful not to
• Do not use any solvent (for example,
damage the connectors.
conventional record cleaner, spray, thinner,
benzine, etc.) to clean discs.
To play new discs
New discs may have some rough
spots around the inner and outer
Connector
edges. If such a disc is used, this
receiver may reject the disc.
Moisture condensation
To remove these rough spots, rub the edges
Moisture may condense on the lens inside the
with a pencil or ball-point pen, etc.
CD player in the following cases:
• After starting the heater in the car.
How to handle SD card
• If it becomes very humid inside the car.
SD cards are precision products. DO NOT
Should this occur, the CD player may
impact, bend, drop, or wet them.
malfunction. In this case, eject the disc and
leave the receiver turned on for a few hours
until the moisture evaporates.
Available character
In addition to the Roman alphabets (A – Z,
How to handle discs
a – z), the following characters will be used.
When removing a disc from
Center holder
• You can also use the following characters
its case, press down the center
to assign titles (see page 46).
holder of the case and lift the
disc out, holding it by the
Accented letters: upper case
edges.
• Always hold the disc by the edges. Do not
touch its recording surface.
When storing a disc into its case, gently insert
Accented letters: lower case
the disc around the center holder (with the
printed surface facing up).
• Make sure to store discs into the cases after
use.
Numbers and symbols
Do not use the following discs:
Sticker
Sticker
Stick-on
Warped
residue
Disc
label
disc
54
EN54-59_KD-SHX851[EY]f.indd 54EN54-59_KD-SHX851[EY]f.indd 54 05.4.11 2:00:29 PM05.4.11 2:00:29 PM
More about this receiver
Basic operations
FM RDS operations
• Network-Tracking Reception requires two
Turning on the power
types of RDS signals—PI (Programme
• By pressing SOURCE on the receiver, you
Identification) and AF (Alternative
can also turn on the power.
Frequency) to work correctly. Without
ENGLISH
receiving these data correctly, Network-
Turning off the power
Tracking Reception will not operate.
• If a DAB tuner is connected and Alternative
• If you turn off the power while listening to a
Frequency Reception for DAB services
disc, disc play will start from where playback
(DAB AF) is activated, Network-Tracking
has been stopped previously, next time you
Reception (AF-Regn’l) is also activated
turn on the power.
automatically. On the other hand, Network-
Tracking Reception cannot be deactivated
Selecting the source
without deactivating Alternative Frequency
• When no disc or SD card is loaded in the
Reception. (See pages 43 and 44.)
receiver, “CD” or “SD” cannot be selected.
• TA Standby Reception and PTY Standby
• Without connecting to the CD changer or
Reception will be temporarily canceled while
DAB tuner, “CD-CH” or “DAB” cannot be
listening to an AM station.
selected.
• Message service requires the RDS Radiotext
• To select the “EXT-IN” for the playback
signal. It is available on most major stations.
source, set the “Ext Input” setting correctly
If reception is weak, the service may become
(see page 44).
unavailable. For any questions regarding the
content of this service, please contact your
broadcaster.
Tuner operations
• If you want to know more about RDS, visit
<http://www.rds.org.uk>.
Storing stations in memory
• During SSM search...
– All previously stored stations are erased and
stations are stored newly.
– Received stations are preset in No. 1 (lowest
frequency) to No. 6 (highest frequency).
– When SSM is over, the station stored in
No. 1 will be automatically tuned in.
• When storing a station manually, a previously
preset station is erased when a new station is
stored in the same preset number.
To be continued....
55
EN54-59_KD-SHX851[EY]f.indd 55EN54-59_KD-SHX851[EY]f.indd 55 05.4.11 2:00:30 PM05.4.11 2:00:30 PM
• This receiver cannot play back mini SD card
Disc/SD card operations
and MMC.
Caution for DualDisc playback
• If the inserted SD card does not have the
• The Non-DVD side of a “DualDisc” does
correct files, you cannot select “SD” for the
not comply with the “Compact Disc Digital
ENGLISH
playback source.
Audio” standard. Therefore, the use of Non-
DVD side of a DualDisc on this product may
Playing a CD-R or CD-RW
not be recommended.
• Use only “finalized” CD-Rs or CD-RWs.
• This receiver can play back only the files of
General
the same type which is first detected if a disc
• This receiver has been designed to reproduce
includes both audio CD (CD-DA) files and
CDs/CD Texts, and CD-Rs (Recordable)/
MP3/WMA files.
CD-RWs (Rewritable) in audio CD (CD-DA),
• This receiver can play back multi-session
MP3 and WMA format and MP3/WMA files
discs; however, unclosed sessions will be
recorded in an SD card.
skipped while playing.
• When a disc or an SD card has been loaded,
• Some CD-Rs or CD-RWs may not play
selecting “CD” or “SD” for the playback
back on this receiver because of their disc
source starts playback.
characteristics, and for the following causes:
– Discs are dirty or scratched.
Inserting a disc
– Moisture condensation occurs on the lens
inside the receiver.
• When a disc is inserted upside down, the
– The pickup lens inside the receiver is dirty.
control panel moves down, and the disc
– CD-R/CD-RW on which the files are
automatically ejects from the loading slot.
written with “Packet Write” method.
• If you keep the control panel open for about 1
– Improper recording conditions (missing
minute, (beeps sound when the “Beep” setting
data, etc.) or media conditions (stain,
is turned “On”—see page 44) the control
scratch, warp, etc.).
panel returns to its previous position.
• CD-RWs may require a longer readout time
since the reflectance of CD-RWs is lower
Playing a disc/SD card
than that of regular CDs.
• While playing an audio CD: If a title has been
• Do not use the following CD-Rs or CD-RWs:
assigned to the audio CD (see page 46), it will
– Discs with stickers, labels, or protective seal
be shown on the display.
stuck to the surface.
• While fast-forwarding or reversing an MP3 or
– Discs on which labels can be directly
WMA track, you can only hear intermittent
printed by an ink jet printer.
sounds.
Using these discs under high temperatures or
• While playing an SD card, the playback order
high humidities may cause malfunctions or
may differ from the one played back using
damages to discs.
other SD players.
• This receiver may be unable to play back
some SD cards due to their characteristics or
recording conditions.
56
EN54-59_KD-SHX851[EY]f.indd 56EN54-59_KD-SHX851[EY]f.indd 56 05.4.11 2:00:30 PM05.4.11 2:00:30 PM
Playing an MP3/WMA track
• For SD cards:
The maximum number of characters for
• This receiver can play back MP3/WMA files
folder name is 8 characters; file name is 12
with the extension code <.mp3> or <.wma>
characters.
(regardless of the letter case—upper/lower).
The receiver cannot recognize folder with
ENGLISH
• This receiver can show the names of albums,
period (.) on the folder name.
artists (performer), and ID3 Tag (Version 1.0,
• This receiver can recognize the total of 512
1.1, 2.2, 2.3, or 2.4) for MP3 files and for
files, of 200 folders, and of 8 hierarchies of an
WMA files.
MP3/WMA disc; 255 files and 63 folders of
• This receiver can display only one-byte
an SD card.
characters. No other characters can be
• This receiver can play back the files recorded
correctly displayed (see page 54).
in VBR (variable bit rate).
• This receiver can play back MP3/WMA files
The files recorded in VBR have a discrepancy
meeting the conditions below:
in elapsed time display, and do not show
– Bit rate: 8 kbps — 320 kbps
the actual elapsed time. Especially, after
– Sampling frequency:
performing the search function, this difference
48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)
becomes noticeable.
24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)
• This receiver cannot play back the following
48 kHz, 44.1 kHz, 32 kHz (for WMA)
files:
– Disc format: ISO 9660 Level 1/ Level 2,
– MP3 files encoded with MP3i and
Romeo, Joliet, Windows long file name
MP3 PRO format.
• For MP3/WMA discs:
– MP3 files encoded in an unappropriated
The maximum number of characters for file/
format.
folder names vary among the disc format used
– MP3 files encoded with Layer 1/2.
(includes 4 extension characters—<.mp3> or
– WMA files encoded with lossless,
<.wma>).
professional, and voice format.
– ISO 9660 Level 1: up to 12 characters
– WMA files which are not based upon
– ISO 9660 Level 2: up to 31 characters
®
Windows Media
Audio.
– Romeo*: up to 128 (72) characters
– WMA files copy-protected with DRM.
– Joliet*: up to 64 (36) characters
– Files which have the data such as WAVE,
– Windows long file name*: up to 128 (72)
ATRAC3, etc.
characters
• The search function works but search speed is
* The parenthetic figure is the maximum
not constant.
number of characters for file/folder names
in case the total number of files and folders
is 313 or more.
To be continued....
57
EN54-59_KD-SHX851[EY]f.indd 57EN54-59_KD-SHX851[EY]f.indd 57 05.4.11 2:00:30 PM05.4.11 2:00:30 PM
Changing the source
Sound adjustments — Daily use
• If you change the source, playback also stops
Selecting the DSP modes—DSP
(without ejecting the disc).
• Effectiveness of “V.Cancel” depends on the
Next time you select “CD,” “SD,” or
recording condition of the sources. Especially,
ENGLISH
“CD-CH” for the playback source, playback
if you play back the following sources you
starts from where it has been stopped
cannot get the satisfactory results.
previously.
– Monaural sources such as AM and
monaural FM broadcasting programs,
ImageLink
– Multiplex sound sources, and
• “Large” ImageLink screen will be temporarily
– Sources recorded with duets, strong echo, a
changed to source operation screen when you
chorus, or only a few instruments.
operate the receiver.
• When “4ch” is selected, rear speakers are
• ImageLink will not work in the following
used only to reproduce reflections and
cases:
reverberations in order to creates a being-
– If no <jpw> fi le is included in an MP3/
there feeling in your car compartment.
WMA folder.
• If fader or balance has been set close to its
– If Intro Scan is activated.
extreme, appropriate effect may not be obtained.
– If the source is changed to another from
• When “Defeat” is selected with crossover
“CD” or “SD.”
network activated, the effect level and the
• If more than one <jpw> fi le are included in a
speaker number setting screens will not
folder, a fi le with the youngest fi le number is
appear.
used for the graphic screen.
Storing your own sound modes
Ejecting a disc
• If you do not want to store your current
• If the ejected disc is not removed within
adjustment, but only to apply the adjustment
15 seconds, the disc is automatically inserted
to the current playback source, press MENU
again into the loading slot to prevent it from
to go back to the operation screen of the
dust. (Disc will not play this time.)
current source. Adjustment you made remains
effective until you select a sound mode.
Sound adjustments
— Preference settings
Setting the basic sound selection menu—SEL
• If you are using a two-speaker system, set the
fader level to the center.
• Subwoofer out setting takes effect only when
a subwoofer is connected.
•
You cannot change the input level—
“VolAdjust” of the FM stations. If the source is
FM, “Fix” will appear when you try to adjust it.
58
EN54-59_KD-SHX851[EY]f.indd 58EN54-59_KD-SHX851[EY]f.indd 58 05.4.11 2:00:30 PM05.4.11 2:00:30 PM
Graphic displays
General settings — PSM
• To set the “PICT” setting as you like,
General
download the required files before setting.
• You can display two sizes of pictures and
If “Default” (for “Picture” and “Movie”)
animations (see page 5).
and “No Slide” (for “Slideshow”) cannot be
ENGLISH
– Large: <jpl> for the still pictures and <jpa>
changed to other options, required files have
for the animations;
not been downloaded.
The image can be shown as the display
• “Auto Dimmer” may not work correctly on
background.
some vehicles, particularly on those having a
– Small: <jpm> for the still pictures and
control dial for dimming. In this case, change
<jpb> for the animations;
the “Dimmer” setting to any one other than
The image is displayed like a CD jacket (in
“Auto.”
the same proportion of CD jacket).
• If you change the “Amp Gain” setting from
“HighPower” to “Low Power” while the
Downloading (or deleting) files
volume level is set higher than “30,” the
• You can download a file only while selecting
receiver automatically changes the volume
“CD” or “SD” for the playback source; on
level to “30.”
the other hand, you can delete a file while
selecting any source.
• If you have already downloaded an animation,
Other main functions
downloading a new animation deletes the
Assigning titles to the sources
previously stored animation.
• It takes a long time to download files.
• If you try to assign a title to a 31st disc,
– About 6 seconds for a still image (one
“Name Full” appears and you cannot enter the
frame).
text entry mode. Delete unwanted titles before
– About 6 minutes for an animation of 60
assignment.
frames.
• Titles assigned to discs in the CD changer can
• If a disc inserted does not include any <jpl>,
also be shown if you play back the disc in the
<jpm>, <jpa>, and <jpb> files, beeps sound
receiver.
when you try to operate the downloading
procedure.
• If you try to store the 17th image for picture
DAB tuner operations
screen for each “Large” and “Small” size,
“Picture Full” appears and you cannot start
• PTY Standby Reception works for the DAB
downloading. Delete unwanted files before
tuner only using a Dynamic PTY, but not a
downloading.
Static PTY.
• TA Standby Reception for FM RDS station
and Road Traffi c News Standby Reception for
DAB cannot be set separately. The T/P button
always work for the both Standby Reception
modes when the DAB tuner is connected.
59
EN54-59_KD-SHX851[EY]f.indd 59EN54-59_KD-SHX851[EY]f.indd 59 05.4.11 2:00:30 PM05.4.11 2:00:30 PM
Troubleshooting
What appears to be trouble is not always serious. Check the following points before calling a service
center.
Symptoms Causes Remedies
ENGLISH
• Sound cannot be heard
The volume level is set to the
Adjust it to the optimum
from the speakers.
minimum level.
level.
Connections are incorrect. Check the cords and
connections.
• The receiver does not work
The built-in microcomputer
Reset the receiver (see page
at all.
may have functioned
2).
incorrectly due to noise, etc.
General
• “Connect Error” appears on
The control panel is not
Remove the control panel,
the display.
attached correctly.
wipe the connector, then
attach it again (see pages 47
and 54).
• “Push Reset” appears on
Something is blocking the
Reset the receiver (see page
the display and the control
control panel movement.
2). If this does not work,
panel movement is freezed.
check the installation.
• SSM automatic presetting
Signals are too weak. Store stations manually.
does not work.
• Static noise while listening
The aerial is not connected
Connect the aerial firmly.
to the radio.
firmly.
• “No Text” appears on the
The station does not support
Check the Network-Tracking
display.
RDS RT or the reception is
Reception (see page 16).
weak.
FM/AM
• “Loading” does not
The receiving signal is
Check the Network-Tracking
disappear.
temporarily too weak to
Reception (see page 16).
receive a complete message
although the service is
available.
• CD-R/CD-RW cannot be
CD-R/CD-RW is not
• Insert a finalized CD-R/
played back.
finalized.
CD-RW.
• Tracks on the CD-R/
• Finalize the CD-R/CD-RW
CD-RW cannot be skipped.
with the component which
you used for recording.
• Disc cannot be ejected. Disc is locked.
Unlock the disc (see page 23).
• Disc cannot be recognized
The CD player may have
Eject the disc forcibly (see
(“No Disc,” “Loading
functioned incorrectly.
page 4).
Error,” or “Eject Error”
Disc playback
appears).
• Disc sound is sometimes
You are driving on rough
Stop playback while driving
interrupted.
roads.
on rough roads.
Disc is scratched. Change the disc.
Connections are incorrect. Check the cords and
connections.
60
EN60-65_KD-SHX851[EY]f.indd 60EN60-65_KD-SHX851[EY]f.indd 60 05.4.11 2:01:12 PM05.4.11 2:01:12 PM
