Gigabyte GA-8I915GL-MF: Chapter 2 BIOS Setup

Chapter 2 BIOS Setup: Gigabyte GA-8I915GL-MF

English

Chapter 2 BIOS Setup

BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure

required settings or to activate certain system features.

The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard.

When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS

SRAM.

When the power is turned on, pushing the <Del> button during the BIOS POST (Power-On Self Test) will

take you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl + F1".

When setting up BIOS for the first time, it is recommended that you save the current BIOS to a disk in the

event that BIOS needs to be reset to its original settings. If you wish to upgrade to a new BIOS, either

Gigabyte's Q-Flash or @BIOS utility can be used.

Q-Flash allows the user to quickly and easily update or backup BIOS without entering the operating system.

@BIOS is a Windows-based utility that does not require users to boot to DOS before upgrading BIOS but

directly download and update BIOS from the Internet.

CONTROL KEYS

< >< >< >< > Move to select item

<Enter> Select Item

<Esc> Main Menu - Quit and not save changes into CMOS Status Page Setup Menu

and Option Page Setup Menu - Exit current page and return to Main Menu

<Page Up> Increase the numeric value or make changes

<Page Down> Decrease the numeric value or make changes

<F1> General help, only for Status Page Setup Menu and Option Page Setup Menu

<F2> Item Help

<F5> Restore the previous CMOS value from CMOS, only for Option Page Setup Menu

<F6> Load the file-safe default CMOS value from BIOS default table

<F7> Load the Optimized Defaults

<F8> Q-Flash utility

<F9> System Information

<F10> Save all the CMOS changes, only for Main Menu

Main Menu

The on-line description of the highlighted setup function is displayed at the bottom of the screen.

Status Page Setup Menu / Option Page Setup Menu

Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selec-

tions for the highlighted item. To exit the Help Window press <Esc>.

BIOS Setup- 29 -

The Main Menu (For example: BIOS Ver. : E3)

Once you enter Award BIOS CMOS Setup Utility, the Main Menu (as figure below) will appear on the

screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.

English

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

` Standard CMOS Features

Load Fail-Safe Defaults

` Advanced BIOS Features

Load Optimized Defaults

` Integrated Peripherals

Set Supervisor Password

` Power Management Setup

Set User Password

` PnP/PCI Configurations

Save & Exit Setup

` PC Health Status

Exit Without Saving

` MB Intelligent Tweaker(M.I.T.)

ESC: Quit KLJI: Select Item

F8: Q-Flash F10: Save & Exit Setup

Time, Date, Hard Disk Type...

If you can't find the setting you want, please press "Ctrl+F1" to search the advanced option

hidden.

Please Load Optimized Defaults in the BIOS when somehow the system works not stable as

usual. This action makes the system reset to the default for stability.

Standard CMOS Features

This setup page includes all the items in standard compatible BIOS.

Advanced BIOS Features

This setup page includes all the items of Award special enhanced features.

Integrated Peripherals

This setup page includes all onboard peripherals.

Power Management Setup

This setup page includes all the items of Green function features.

PnP/PCI Configuration

This setup page includes all the configurations of PCI & PnP ISA resources.

PC Health Status

This setup page is the System auto detect Temperature, voltage, fan, speed.

MB Intelligent Tweaker(M.I.T.)

This setup page is control CPU clock and frequency ratio.

Load Fail-Safe Defaults

Fail-Safe Defaults indicates the value of the system parameters which the system would be in safe

configuration.

Load Optimized Defaults

Optimized Defaults indicates the value of the system parameters which the system would be in best

performance configuration.

Set Supervisor Password

Change, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup.

GA-8I915GL-MF Motherboard - 30 -

Set User Password

English

Change, set, or disable password. It allows you to limit access to the system.

Save & Exit Setup

Save CMOS value settings to CMOS and exit setup.

Exit Without Saving

Abandon all CMOS value changes and exit setup.

BIOS Setup- 31 -

2-1 Standard CMOS Features

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

Standard CMOS Features

Date (mm:dd:yy) Thu, Apr 29 2004

Item Help

English

Time (hh:mm:ss) 22:31:24

Menu Level`

` IDE Channel 0 Master [None]

Change the day, month,

` IDE Channel 0 Slave [None]

year

` IDE Channel 2 Master [None]

` IDE Channel 2 Slave [None]

<Week>

` IDE Channel 3 Master [None]

Sun. to Sat.

` IDE Channel 3 Slave [None]

<Month>

Drive A [1.44M, 3.5"]

Jan. to Dec.

Drive B [None]

Floppy 3 Mode Suport [Disabled]

<Day>

1 to 31 (or maximum

Halt On [All, But Keyboard]

allowed in the month)

Base Memory 640K

<Year>

Extended Memory 127M

1999 to 2098

Total Memory 128M

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Safe Default F7: Optimized Defaults

Date

The date format is <week>, <month>, <day>, <year>.

Week The week, from Sun to Sat, determined by the BIOS and is display only

Month The month, Jan. Through Dec.

Day The day, from 1 to 31 (or the maximum allowed in the month)

Year The year, from 1999 through 2098

Time

The times format in <hour> <minute> <second>. The time is calculated base on the 24-hour

military-time clock. For example, 1 p.m. is 13:00:00.

IDE Channel 0/2/3 Master, Slave

IDE HDD Auto-Detection Press "Enter" to select this option for automatic device detection.

IDE Channel 0/2/3 Master(Slave) IDE Device Setup. You can use one of three methods:

Auto Allows BIOS to automatically detect IDE devices during POST(default)

None Select this if no IDE devices are used and the system will skip the automatic

detection step and allow for faster system start up.

Manual User can manually input the correct settings

Access Mode Use this to set the access mode for the hard drive. The four options are:

CHS/LBA/Large/Auto(default:Auto)

Hard drive information should be labeled on the outside drive casing. Enter the appropriate option

based on this information.

Cylinder Number of cylinders

Head Number of heads

Precomp Write precomp

Landing Zone Landing zone

Sector Number of sectors

If a hard disk has not been installed, select NONE and press <Enter>.

GA-8I915GL-MF Motherboard - 32 -

Drive A / Drive B

English

The category identifies the types of floppy disk drive A or drive B that has been installed in the

computer.

None No floppy drive installed

360K, 5.25" 5.25 inch PC-type standard drive; 360K byte capacity.

1.2M, 5.25" 5.25 inch AT-type high-density drive; 1.2M byte capacity

(3.5 inch when 3 Mode is Enabled).

720K, 3.5" 3.5 inch double-sided drive; 720K byte capacity

1.44M, 3.5" 3.5 inch double-sided drive; 1.44M byte capacity.

2.88M, 3.5" 3.5 inch double-sided drive; 2.88M byte capacity.

Floppy 3 Mode Support (for Japan Area)

Disabled Normal Floppy Drive. (Default value)

Drive A Drive A is 3 mode Floppy Drive.

Drive B Drive B is 3 mode Floppy Drive.

Both Drive A & B are 3 mode Floppy Drives.

Halt on

The category determines whether the computer will stop if an error is detected during power up.

No Errors The system boot will not stop for any error that may be detected and you

will be prompted.

All Errors Whenever the BIOS detects a non-fatal error the system will be stopped.

All, But Keyboard The system boot will not stop for a keyboard error; it will stop for all other

errors. (Default value)

All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors.

All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all

other errors.

Memory

The category is display-only which is determined by POST (Power On Self Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory installed

in the system.

The value of the base memory is typically 512K for systems with 512K memory installed on

the motherboard, or 640K for systems with 640K or more memory installed on the motherboard.

Extended Memory

The BIOS determines how much extended memory is present during the POST.

This is the amount of memory located above 1 MB in the CPU's memory address map.

BIOS Setup- 33 -

2-2 Advanced BIOS Features

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

Advanced BIOS Features

English

` Hard Disk Boot Priority [Press Enter]

Item Help

First Boot Device [Floppy]

Menu Level`

Second Boot Device [Hard Disk]

Third Boot Device [CDROM]

Select Hard Disk Boot

Password Check [Setup]

Device Priority

# CPU Hyper-Threading [Enabled]

Limit CPUID Max. to 3 [Enabled]

No-Execute Memory Protect

(Note)

[Disabled]

CPU Enhanced Halt (C1E)

(Note)

[Disabled]

CPU Thermal Monitor 2(TM2)

(Note)

[Disabled]

On-Chip Frame Buffer Size [8MB]

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Safe Default F7: Optimized Defaults

" # " System will detect automatically and show up when you install the Intel

®

Pentium

®

4

processor with HT Technology.

Hard Disk Boot Priority

Select boot sequence for onboard(or add-on cards) SCSI, RAID, etc.

Use < > or < > to select a device, then press<+> to move it up, or <-> to move it down the list. Press

<ESC> to exit this menu.

First / Second / Third Boot Device

Floppy Select your boot device priority by Floppy.

LS120 Select your boot device priority by LS120.

Hard Disk Select your boot device priority by Hard Disk.

CDROM Select your boot device priority by CDROM.

ZIP Select your boot device priority by ZIP.

USB-FDD Select your boot device priority by USB-FDD.

USB-ZIP Select your boot device priority by USB-ZIP.

USB-CDROM Select your boot device priority by USB-CDROM.

USB-HDD Select your boot device priority by USB-HDD.

LAN Select your boot device priority by LAN.

Disabled Disabled this function.

(Note) This item will show up when you install a processor which supports this function.

GA-8I915GL-MF Motherboard - 34 -

Password Check

English

Setup The system will boot but will not access to Setup page if the correct

password is not entered at the prompt. (Default value)

System The system will not boot and will not access to Setup page if the correct

password is not entered at the prompt.

CPU Hyper-Threading

Enabled Enables CPU Hyper Threading Feature. Please note that this feature is only

working for operating system with multi processors mode supported.

(Default value)

Disabled Disables CPU Hyper Threading.

Limit CPUID Max. to 3

Enabled Limit CPUID Maximum value to 3 when use older OS like NT4. (Default value)

Disabled Disables CPUID Limit for windows XP.

(Note)

No-Execute Memory Protect

Enabled Enables No-Execute Memory Protect function.

Disabled Disables No-Execute Memory Protect function. (Default value)

(Note)

CPU Enhanced Halt (C1E)

Enabled Enables CPU Enhanced Halt (C1E) function.

Disabled Disables CPU Enhanced Halt (C1E) function. (Default value)

(Note)

CPU Thermal Monitor 2 (TM2)

Enabled Enable CPU Thermal Monitor 2 (TM2) function.

Disabled Disable CPU Thermal Monitor 2 (TM2) function. (Default value)

On-Chip Frame Buffer Size

1MB Set On-chip frame buffer size to 1MB.

4MB Set On-chip frame buffer size to 4MB.

8MB Set On-chip frame buffer size to 8MB. (Default value)

16MB Set On-chip frame buffer size to 16MB.

32MB Set On-chip frame buffer size to 32MB.

(Note) This item will show up when you install a processor which supports this function.

BIOS Setup- 35 -

2-3 Integrated Peripherals

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

Integrated Peripherals

English

On-Chip Primary PCI IDE [Enabled]

Item Help

On-Chip SATA Mode [Auto]

Menu Level`

x PATA IDE Set to Ch.1 Master/Slave

SATA Port 0/2 Set to Ch.2 Master/Slave

SATA Port 1/3 Set to Ch.3 Master/Slave

USB Controller [Enabled]

USB 2.0 Controller [Enabled]

USB Keyboard Support [Disabled]

USB Mouse Support [Disabled]

Azalia Codec [Auto]

Front Panel Type [HD Audio]

Onboard H/W 1394 [Enabled]

Onboard H/W LAN [Enabled]

Onboard LAN Boot ROM [Disabled]

Onboard Serial Port 1 [3F8/IRQ4]

Onboard Serial Port 2 [2F8/IRQ3]

UART Mode Select [Normal]

x UR2 Duplex Mode [Half]

Onboard Parallel Port [378/IRQ7]

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Safe Default F7: Optimized Defaults

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

Integrated Peripherals

Parallel Port Mode [SPP]

Item Help

x ECP Mode Use DMA 3

Menu Level`

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Safe Default F7: Optimized Defaults

On-Chip Primary PCI IDE

Enabled Enable onboard 1st channel IDE port. (Default value)

Disabled Disable onboard 1st channel IDE port.

GA-8I915GL-MF Motherboard - 36 -

On-Chip SATA Mode

English

Disabled Disable this function.

Auto BIOS will auto detect. (Default value)

Combined Set On-Chip SATA mode to Combined, you can use up to 4 HDDs on

the motherboard; 2 for SATA and the other for PATA IDE.

Enhanced Set On-Chip SATA mode to Enhanced, the motherboard allows up to 6

HDDs to use.

Non-Combined Set On-Chip SATA mode to Non-Combined, SATA will be simulated to

PATA mode.

PATA IDE Set to

Ch.1 Master/Slave Set PATA IDE to Ch. 1 Master/Slave. (Default value)

Ch.0 Master/Slave Set PATA IDE to Ch. 0 Master/Slave.

SATA Port 0/2 Set to

This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".

If PATA IDE were set to Ch. 1 Master/Slave, this function will auto set to Ch. 0 Master/Slave.

SATA Port 1/3 Set to

This value will auto make by the setting "On-Chip SATA Mode" and "PATA IDE Set to".

If PATA IDE were set to Ch. 0 Master/Slave, this function will auto set to Ch. 1 Master/Slave.

USB Controller

Enabled Enable USB Controller. (Default value)

Disabled Disable USB Controller.

USB 2.0 Controller

Disable this function if you are not using onboard USB 2.0 feature.

Enabled Enable USB 2.0 Controller. (Default value)

Disabled Disable USB 2.0 Controller.

USB Keyboard Support

Enabled Enable USB Keyboard Support.

Disabled Disable USB Keyboard Support. (Default value)

USB Mouse Support

Enabled Enable USB Mouse Support.

Disabled Disable USB Mouse Support. (Default value)

Azalia Codec

Auto Auto detect Azalia audio function. (Default value)

Disabled Disable Azalia audio function.

Front Panel Type

If you connect HD Audio Panel to the AZALIA_FP connector, set this item to HD Audio. If you

connect AC97 Audio Panel to the AZALIA_FP connector, set this item to AC97.

AC97 Set front audio panel type to AC97.

HD Audio Set front audio panel type to HD Audio. (Default value)

BIOS Setup- 37 -

Onboard H/W 1394

Enabled Enable onboard IEEE 1394 function.(Default value)

Disabled Disable this function.

English

Onboard H/W LAN

Enabled Enable Onboard H/W LAN function. (Default value)

Disabled Disable this function.

Onboard LAN Boot ROM

This function decide whether to invoke the boot ROM of the onboard LAN chip.

Enabled Enable this function.

Disabled Disable this function. (Default value)

Onboard Serial Port 1

Auto BIOS will automatically setup the port 1 address.

3F8/IRQ4 Enable onboard Serial port 1 and address is 3F8. (Default value)

2F8/IRQ3 Enable onboard Serial port 1 and address is 2F8.

3E8/IRQ4 Enable onboard Serial port 1 and address is 3E8.

2E8/IRQ3 Enable onboard Serial port 1 and address is 2E8.

Disabled Disable onboard Serial port 1.

Onboard Serial Port 2

Auto BIOS will automatically setup the port 2 address.

3F8/IRQ4 Enable onboard Serial port 2 and address is 3F8.

2F8/IRQ3 Enable onboard Serial port 2 and address is 2F8. (Default value)

3E8/IRQ4 Enable onboard Serial port 2 and address is 3E8.

2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8.

Disabled Disable onboard Serial port 2.

UART Mode Select

This item allows you to determine which Infra Red(IR) function of Onboard I/O chip.

Normal Set onboard I/O chip UART to Normal Mode. (Default Value)

ASKIR Set onboard I/O chip UART to ASKIR Mode.

IrDA Set onboard I/O chip UART to IrDA Mode.

UR2 Duplex Mode

This feature allows you to seclect IR mode.

This function will available when "UART Mode Select" doesn't set at Normal.

Half IR Function Duplex Half. (Default value)

Full IR Function Duplex Full.

Onboard Parallel port

Disabled Disable onboard LPT port.

378/IRQ7 Enable onboard LPT port and address is 378/IRQ7. (Default value)

278/IRQ5 Enable onboard LPT port and address is 278/IRQ5.

3BC/IRQ7 Enable onboard LPT port and address is 3BC/IRQ7.

GA-8I915GL-MF Motherboard - 38 -

Parallel Port Mode

English

SPP Using Parallel port as Standard Parallel Port. (Default value)

EPP Using Parallel port as Enhanced Parallel Port.

ECP Using Parallel port as Extended Capabilities Port.

ECP+EPP Using Parallel port as ECP & EPP mode.

ECP Mode Use DMA

3 Set ECP Mode Use DMA to 3. (Default value)

1 Set ECP Mode Use DMA to 1.

2-4 Power Management Setup

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

Power Management Setup

ACPI Suspend Type [S1(POS)]

Item Help

Soft-Off by PWR-BTTN [Instant-off]

Menu Level`

PME Event Wake Up [Enabled]

Power On by Ring [Enabled]

Resume by Alarm [Disabled]

x Date (of Month) Alarm Everyday

x Time (hh:mm:ss) Alarm 0 : 0 : 0

Power On By Mouse [Disabled]

Power On By Keyboard [Disabled]

x KB Power ON Password Enter

AC Back Function [Soft-Off]

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Safe Default F7: Optimized Defaults

ACPI Suspend Type

S1(POS) Set ACPI suspend type to S1/POS(Power On Suspend). (Default value)

S3(STR) Set ACPI suspend type to S3/STR(Suspend To RAM).

Soft-off by PWR-BTTN

Instant-off Press power button then Power off instantly. (Default value)

Delay 4 Sec. Press power button 4 sec. to Power off. Enter suspend if button is pressed

less than 4 sec.

PME Event Wake Up

Disabled Disable this function.

Enabled Enable PME Event Wake up. (Default value)

Power On by Ring

Disabled Disable Power on by Ring function.

Enabled Enable Power on by Ring function. (Default value)

BIOS Setup- 39 -

Resume by Alarm

You can set "Resume by Alarm" item to enabled and key in Date/time to power on system.

Disabled Disable this function. (Default value)

Enabled Enable alarm function to POWER ON system.

English

If RTC Alarm Lead To Power On is Enabled.

Date (of Month) Alarm : Everyday, 1~31

Time (hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59)

Power On By Mouse

Disabled Disable this function. (Default value)

Double Click Double click on PS/2 mouse left button to power on the system.

Power On By Keyboard

Password Enter from 1 to 5 characters to set the Keyboard Power On Password.

Disabled Disabled this function. (Default value)

Keyboard 98 If your keyboard have "POWER Key" button, you can press the key to

power on the system.

KB Power ON Password

When "Power On by Keyboard" set at Password, you can set the password here.

Enter Input password (from 1 to 5 characters) and press Enter to set the Keyboard

Power On password.

AC Back Function

Soft-Off When AC-power back to the system, the system will be in "Off" state.

(Default value)

Full-On When AC-power back to the system, the system always in "On" state.

Memory When AC-power back to the system, the system will return to the Last state

before AC-power off.

GA-8I915GL-MF Motherboard - 40 -

English

2-5 PnP/PCI Configurations

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

PnP/PCI Configurations

PCI 1 IRQ Assignment [Auto]

Item Help

PCI 2 IRQ Assignment [Auto]

Menu Level`

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Safe Default F7: Optimized Defaults

PCI 1 IRQ Assignment

Auto Auto assign IRQ to PCI 1. (Default value)

3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1.

PCI 2 IRQ Assignment

Auto Auto assign IRQ to PCI 2. (Default value)

3,4,5,7,9,10,11,12,14,15 Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.

2-6 PC Health Status

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

PC Health Status

Reset Case Open Status [Disabled]

Item Help

Case Opened Yes

Menu Level`

Vcore OK

DDR25V OK

+3.3V OK

+12V OK

Current CPU Temperature 33

o

C

Current CPU FAN Speed 4687 RPM

Current SYSTEM FAN Speed 0 RPM

CPU Warning Temperature [Disabled]

CPU FAN Fail Warning [Disabled]

SYSTEM FAN Fail Warning [Disabled]

CPU Smart FAN Control [Enabled]

CPU Smart FAN Mode [Auto]

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Safe Default F7: Optimized Defaults

BIOS Setup- 41 -

Reset Case Open Status

Case Opened

English

If the case is closed, "Case Opened" will show "No".

If the case have been opened, "Case Opened" will show "Yes".

If you want to reset "Case Opened" value, set "Reset Case Open Status" to

"Enabled" and save CMOS, your computer will restart.

Current Voltage(V) Vcore / DDR25V / +3.3V / +12V

Detect system's voltage status automatically.

Current CPU Temperature

Detect CPU temperature automatically.

Current CPU/SYSTEM FAN Speed (RPM)

Detect CPU/SYSTEM Fan speed status automatically.

CPU Warning Temperature

o

o

o

o

60

C / 140

F Monitor CPU temperature at 60

C / 140

F.

o

o

o

o

70

C / 158

F Monitor CPU temperature at 70

C / 158

F.

o

o

o

o

80

C / 176

F Monitor CPU temperature at 80

C / 176

F.

o

o

o

o

90

C / 194

F Monitor CPU temperature at 90

C / 194

F.

Disabled Disable this function. (Default value)

CPU/SYSTEM FAN Fail Warning

Disabled Fan warning function disable. (Default value)

Enabled Fan warning function enable.

CPU Smart FAN Control

Disabled Disable this function.

Enabled Enable CPU Smart Fan control function. (Default value)

a. When the CPU temperature is higher than 65 degrees Celsius, CPU fan

will run at full speed.

b. The speed of CPU fan will increase linearly depand on the temperature

if the temperature is more than 41 degree and less than 65 degree.

c. When the CPU temperature is lower than 40 degrees Celsius, CPU fan

willbe disable.

CPU Smart FAN Mode

This option is available only when CPU Smart FAN Control is enabled.

Auto BIOS autodetects the type of CPU fan you installed and sets the optimal CPU

Smart FAN control mode for it. (Default Value)

Voltage Set to Voltage when you use a CPU fan with a 3-pin fan power cable.

PWM Set to PWM when you use a CPU fan with a 4-pin fan power cable.

Note: In fact, the Voltage option can be used for CPU fans with 3-pin or 4-pin power cables.

However, some 4-pin CPU fan power cables are not designed following Intel 4-Wire fans PWM

control specifications. With such CPU fans, selecting PWM will not effectively reduce the fan

speed.

GA-8I915GL-MF Motherboard - 42 -

English

2-7 MB Intelligent Tweaker(M.I.T.)

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

MB Intelligent Tweaker(M.I.T.)

CPU Clock Ratio [15X]

Item Help

Memory Frequency For [Auto]

Menu Level`

Memory Frequency (Mhz) 400

KLJI: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help

F5: Previous Values F6: Fail-Safe Default F7: Optimized Defaults

Incorrect using these features may cause your system broken. For power end-user use only.

CPU Clock Ratio

This setup option will automatically assign by CPU detection.

The option will display "Locked" and read only if the CPU ratio is not changeable.

Memory Frequency For

Wrong frequency may make system can't boot, clear CMOS to overcome wrong frequency issue.

for FSB(Front Side Bus) frequency=533MHz,

3.0 Memory Frequency = Host clock X 3.0.

4.0 Memory Frequency = Host clock X 4.0.

Auto Set Memory frequency by DRAM SPD data. (Default value)

for FSB(Front Side Bus) frequency=800MHz,

2.0 Memory Frequency = Host clock X 2.0.

2.66 Memory Frequency = Host clock X 2.66.

Auto Set Memory frequency by DRAM SPD data. (Default value)

Memory Frequency (Mhz)

The values depend on "Memory Frequency For" item.

BIOS Setup- 43 -

2-8 Load Fail-Safe Defaults

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

` Standard CMOS Features

Load Fail-Safe Defaults

English

` Advanced BIOS Features

Load Optimized Defaults

` Integrated Peripherals

Set Supervisor Password

` Power Management Setup

Set User Password

` PnP/PCI Configurations

Load Fail-Safe Defaults (Y/N)? N

Save & Exit Setup

` PC Health Status

Exit Without Saving

` MB Intelligent Tweaker(M.I.T.)

ESC: Quit KLJI: Select Item

F8: Q-Flash F10: Save & Exit Setup

Load Fail-Safe Defaults

Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system

performance.

2-9 Load Optimized Defaults

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

` Standard CMOS Features

Load Fail-Safe Defaults

` Advanced BIOS Features

Load Optimized Defaults

` Integrated Peripherals

Set Supervisor Password

` Power Management Setup

Set User Password

` PnP/PCI Configurations

Load Optimized Defaults (Y/N)? N

Save & Exit Setup

` PC Health Status

Exit Without Saving

` MB Intelligent Tweaker(M.I.T.)

ESC: Quit KLJI: Select Item

F8: Q-Flash F10: Save & Exit Setup

Load Optimized Defaults

Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically

detects.

GA-8I915GL-MF Motherboard - 44 -

English

2-10 Set Supervisor/User Password

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

` Standard CMOS Features

Load Fail-Safe Defaults

` Advanced BIOS Features

Load Optimized Defaults

` Integrated Peripherals

Set Supervisor Password

` Power Management Setup

Set User Password

` PnP/PCI Configurations

Enter Password:

Save & Exit Setup

` PC Health Status

Exit Without Saving

` MB Intelligent Tweaker(M.I.T.)

ESC: Quit KLJI: Select Item

F8: Q-Flash F10: Save & Exit Setup

Change/Set/Disable Password

Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically

detects.

When you select this function, the following message will appear at the center of the screen to assist you in

creating a password.

Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password.

Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter

a password.

To disable password, just press <Enter> when you are prompted to enter password. A message

"PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is disabled,

the system will boot and you can enter Setup freely.

The BIOS Setup program allows you to specify two separate passwords:

SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS Setup

program function. When enabled, the Supervisor password is required for entering the BIOS Setup program

and having full configuration fields, the User password is required to access only basic items.

If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be prompted for the

password every time the system is rebooted or any time you try to enter Setup Menu.

If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only when

you try to enter Setup.

BIOS Setup- 45 -

2-11 Save & Exit Setup

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

English

` Standard CMOS Features

Load Fail-Safe Defaults

` Advanced BIOS Features

Load Optimized Defaults

` Integrated Peripherals

Set Supervisor Password

` Power Management Setup

Set User Password

` PnP/PCI Configurations

Save & Exit Setup

` PC Health Status

Save to CMOS and EXIT (Y/N)? Y

Exit Without Saving

` MB Intelligent Tweaker(M.I.T.)

ESC: Quit KLJI: Select Item

F8: Q-Flash F10: Save & Exit Setup

Save & Exit Setup

Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS.

Type "N" will return to Setup Utility.

2-12 Exit Without Saving

CMOS Setup Utility-Copyright (C) 1984-2005 Award Software

` Standard CMOS Features

Load Fail-Safe Defaults

` Advanced BIOS Features

Load Optimized Defaults

` Integrated Peripherals

Set Supervisor Password

` Power Management Setup

Set User Password

` PnP/PCI Configurations

Quit Without Saving (Y/N)? N

Save & Exit Setup

` PC Health Status

Exit Without Saving

` MB Intelligent Tweaker(M.I.T.)

ESC: Quit KLJI: Select Item

F8: Q-Flash F10: Save & Exit Setup

Abandon all Data

Type "Y" will quit the Setup Utility without saving to RTC CMOS.

Type "N" will return to Setup Utility.

GA-8I915GL-MF Motherboard - 46 -